ZyXEL Communications VMG1312 User manual

1.
Router Set-up Guide - ZYXEL VMG1312 for FTTC
Connections
ZYXEL VMG1312-B10D
Router Setup for FTTC Connections
Contents
Router Logon ........................................................................................................................ 3
Configure Connection ........................................................................................................... 5
LAN/DHCP Setup……………………………………………………………………………………………………………….9
Wi-Fi .....................................................................................................................................11
Firmware Upgrade .............................................................................................................. 12
Remote Management ......................................................................................................... 14
SNMP ................................................................................................................................... 16
Support Contact Details ....................................................................................................... 18
Router Logon
Open a web browser on your PC or laptop and enter the following address: http://192.168.1.1
This will bring up the login screen for the router as seen below:
- it is recommended to connect DSL cable to DSL port behind the router first before starting the configuration of the router.Note

1.
1.
1.
Enter the login credentials as follows:
Username: admin
default (1234)Password:
-If the router has retained its original configuration as shipped by Cerberus Networks, the password would have been changed. The latest passwordNote
can be found in your Cerberus documentation.
If the router was in a factory default state, it will now prompt you to change the password. Please choose a new password and save it for your
records.
After navigating the password stage, the router will launch a Quick Start Wizard:

1.
1.
Please click on the ' option at the bottom of the screen. Closing the Wizard will bring up the main dashboard of the router as seen in the next sectionSkip'
– Configure Connection.
Configure Connection
On the main dashboard of the router, click on the menu button at the top-right corner of the screen in order to display more options:
Click on 3) SelectNetwork Settings Broadband

1.
1.
4) Click on the edit option for VDSL at the end of row 2 (marked in Red):
Make the following changes under General:
Set Mode to .Routing
Set Encapsulation to .PPPoE
Change IPv4/IPv6 Mode to .IPv4 only
Make the following changes under PPP Information:

1.
1.
1.
Enter the PPP Username. This can be found in your Cerberus documentation.
Enter the PPP password. This is also in your Cerberus documentation.
Make sure to change VLAN option to 101 & Change the MTU to 1492 as per below snapshot.
Ensure IP Address and DNS Server options are set to automatic:
Ensure the following Routing Features are enabled:
NAT
IGMP Proxy
Apply as Default Gateway

1.
1.
1.
Click on ' at the bottom of the screen to save your settings.Apply' Your internet connection should now be online.
LAN/DHCP Setup
On the main dashboard of the router, click on the menu button at the top-right corner of the screen in order to display more options:
Select 3) ClickNetwork Settings Home Networking

1.
4) DHCP Server state is ticked as Enabled by default as mentioned in below snapshot. Customer can disable it if they don't wish to use Router as a DHCP
Server.
5) Also please make sure option deactivate (Blue to Grey) in case customer doesn't want to use IPv6 option by default.IPv6 Active
Click on to save changes.Apply
Please proceed to the next page and beyond for guidance on Wi-Fi, firmware upgrades, remote management and SNMP.
Wi-Fi
The Zyxel VMG3925 router comes with two pre-configured Wi-Fi networks. The names (or SSIDs) of the two networks and their passwords can be found
on the manufacturer's label on the rear panel of the router.
Please note that the 2.4G option can offer better Wi-Fi coverage at greater distances, although it may see lower speeds in comparison to the 5G option.
If you wish to change the or passwords of the Wi-Fi networks, the basic settings are available through the following steps:names
Click on the Wi-Fi menu button on the main dashboard:

1.
1.
Change the Wi-Fi network name and password as per your preferences:
Click on ' apply your settings.Save' to
Firmware Upgrade
Visit the following URL for the latest firmware:
ftp://ftp.zyxel.com/VMG1312-B10D/firmware/
2) Download the latest zip file, for e.g. VMG1312-B10D_V513AAXA10C0.zip.
3) Open the zip file and extract the folder within it to a location on your PC or laptop.
4) On the main dashboard of the router, click on the menu button at the top-right corner of the screen in order to display more options:
`5) Click on :Maintenance

1.
6) Select Firmware Upgrade
7) Click on Choose File and then navigate to the location of your saved folder as seen in Step 3. Select the file ending .bin, for example, V513AAXA10C0.
bin:
8) Once you have selected the firmware file, click on to begin the upgrade. Please note this process will take 2-3 minutes to complete and theUpload
router will reboot during this process:
Remote Management
Remote management is an optional feature should you wish to access your router remotely across the internet or provide such access to Cerberus
Networks for troubleshooting purposes or NetStats bandwidth monitoring.
On the main dashboard of the router, click on the menu button at the top-right corner of the screen in order to display more options:

1. Click on 3) Select :Maintenance: Remote Management
4) In the remote management table, all options under WAN are unticked by default. Please tick the following options:
HTTPS
PING (this is required if you want Cerberus to allow ping of router WAN IP over the Internet)
SSH
SNMP (this is only required if you wish to enable SNMP for bandwidth monitoring, as shown in the next section)