ZZap CS20 User manual

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
1$
!"#$%&#'
Thank$you$for$purchasing$the$ZZap$CS20$coin$counter$and$sorter.$The$CS20$makes$manual$
counting$and$sorting$a$thing$of$the$past.$As$you$relax,$the$CS20$will$count$and$sort$your$coins$
fast$and$accurately$while$displaying$the$total$value$counted$on$its$large$LED$display.$At$the$
end$of$the$cycle$the$CS20$will$automatically$stop$and$report$the$total$quantity$counted$per$
denomination.$
()*+#*+,$
-.'/%$#+0'1*,+"2&+1)*,.............................................................................................. 2$
3.'4*+")52&+1)* ....................................................................................................... 2$
2.1$ $ Features........................................................................................................................2$
2.2$ $ Package$contents..........................................................................................................2$
6.'78+#"1)"'$#%+2"#,.................................................................................................3$
9.':;#"%+1*<'1*,+"2&+1)*, ........................................................................................ 3$
4.1$ $Counting$and$sorting ....................................................................................................3$
4.2$ $ Batch$counting..............................................................................................................3$
=.'>%1*+#*%*&#'%*5'<#*#"%?'2,#............................................................................. 4$
5.1$ $Removing$foreign$coins/objects$from$inside$the$machine...........................................4$
5.2$ $ Removing$jammed$coins$from$a$coin$channel..............................................................5$
5.3$ $ Error$messages .............................................................................................................5$
@.'/;#&1$1&%+1)*, ..................................................................................................... 6$
$
$
$
$
$
$
$
$
$
$
$
$
$
$ $
$
$
$

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
2$
-.'/%$#+0'1*,+"2&+1)*,'
Read$the$safety$instructions$before$operating$the$ZZap$CS20$in$order$to$avoid$personal$injury$
and$damage$to$the$machine.$ $
$
$
$
$
$
•Do$not$put$foreign$coins/objects$in$the$hopper.$
•Before$carrying$out$maintenance,$make$sure$the$machine$is$
switched$off$and$the$plug$is$disconnected$from$the$power$
supply.$ $
•Do$not$put$fingers$inside$the$hopper$or$coin$channels$when$
the$machine$is$turned$on.$
•Do$not$drop$metal$objects$or$flammable$materials$inside$the$
machine.$
•Do$not$operate$the$machine$when$the$back$cover$is$open.$
•Switch$off$the$machine$after$use.$
•Disconnect$the$power$supply$if$the$machine$is$expected$to$be$
out$of$service$for$extended$periods$of$time.$ $
•Do$not$operate$the$machine$in$high$temperatures$or$
humid/damp$conditions.$
•Do$not$operate$the$machine$with$wet$hands.$
•Follow$all$the$warnings$and$instructions$marked$on$the$
machine$(if$applicable).$
•Ensure$that$the$mains$power$supply$is$compatible$with$the$
machine.$ $
•Disconnect$the$power$supply$before$moving$the$machine.$
•Replace$the$fuse$if$it$has$blown:$open$the$cover$of$the$fuse$
holder,$discard$the$blown$fuse$and$replace$it$with$a$new$fuse$
of$the$same$type$and$rating.$
$
$
$
$
3.'4*+")52&+1)*'
2.1$Features$
•Counts$up$to$220$coins$per$minute.!
•Batch$and$add$function.$
•Reports$total$value$and$quantity$per$denomination.$
•Automatic$stop$function.$
•Counts$all$denominations.$ $
2.2$Package$contents$
The$package$includes$the$following:$
•CS20$coin$counter$and$sorter.$
•8$coin$trays.$
•Power$lead.$
•User$manual.$
$
!$
$

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
3$
6.'78+#"1)"'$#%+2"#,'
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
9.':;#"%+1*<'1*,+"2&+1)*,'
4.1$Counting$and$sorting$
1) Place$the$machine$on$a$level$surface.$
2) Turn$on$the$machine$at$the$on/off$switch.$
3) Remove$any$foreign$coins/objects$then$put$the$coins$in$the$hopper.$ $
4) Press$the$“START/STOP”$button$to$start$counting.$Press$the$“START/STOP”$button$
again$to$stop$counting.$
5) The$total$value$counted$will$be$displayed$on$the$screen.$ $
6) To$display$the$counting$result$for$each$coin$denomination,$press$the$“REPORT”$
button$when$counting$is$complete.$Press$the$“C”$button$to$exit$report$mode.$
4.2$Batch$counting$
1) Place$the$machine$on$a$level$surface.$
2) Turn$on$the$machine$at$the$on/off$switch.$
3) Set$a$batch$quantity$for$each$coin$denomination:$
a.$Press$the$“SET”$button$to$select$a$coin$denomination$(shown$on$the$left$hand$
side$of$the$display).$
b.$Press$the$“BATCH”,$“+”$and$“[“$button$to$set$a$batch$quantity$between$0$and$
999$(shown$on$the$right$hand$side$of$the$display).$
4) To$start$counting,$put$the$coins$in$the$hopper$and$press$the$“START/STOP”$button.$
5) Press$the$“START/STOP”$button$at$any$time$to$stop$counting.$
6) When$a$batch$has$been$counted$the$CS20$will$automatically$stop$and$emit$a$“beep”$
sound.$The$applicable$denomination$and$its$batch$quantity$will$be$displayed.$
7) Remove$the$coins$from$the$applicable$coin$tray$and$press$the$“START/STOP”$button$
to$continue$batch$counting.$

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
4$
A)+#'4:$If$the$batch$quantity$is$set$to$0$the$CS20$will$continue$to$count$the$applicable$
denomination$unless$the$“START/STOP”$button$is$pressed$or$if$no$coins$are$counted$within$
20$seconds.$
A)+#'44:$To$set$all$the$batch$quantities$to$0:$press$and$hold$the$“[“$button$for$7$seconds$until$
“C”$appears$on$the$left$hand$side$of$the$display.$
A)+#'444:$The$current$batch$settings$will$be$remembered$when$the$CS20$is$next$switched$on.$
=.'>%1*+#*%*&#'%*5'<#*#"%?'2,#'
Before$cleaning/maintaining$the$machine,$make$sure$the$CS20$is$switched$off$and$the$plug$is$
disconnected$from$the$power$supply.$Periodically$clean$the$machine$with$a$cloth$to$remove$
dust$and$dirt.$In$the$event$of$a$coin$jam$see$section$5.1$and$5.2.$If$the$coin$jam$is$still$not$
resolved:$
1) Switch$off$the$machine$and$disconnect$the$power$supply.$
2) Unscrew$and$remove$the$3$screws$near$the$bottom$of$the$cover.$
3) Remove$the$cover$and$remove$any$jammed$coins.$
5.1$Removing$foreign$coins/objects$from$inside$the$machine$
Foreign$coins/objects$will$cause$the$machine$to$jam$and$may$damage$the$machine.$To$
remove$foreign$coins/objects$from$inside$the$machine,$make$sure$the$CS20$is$switched$off$
and$the$plug$is$disconnected$from$the$power$supply,$open$the$back$cover$and$remove$the$
foreign$coins/objects.$Also$remove$dust$and$dirt$where$possible.$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
5$
5.2$Removing$jammed$coins$from$a$coin$channel$
Coins$may$become$jammed$in$a$coin$channel.$To$remove$jammed$coins,$make$sure$the$CS20$
is$switched$off$and$the$plug$is$disconnected$from$the$power$supply.$Use$a$finger$to$push$up$
through$the$coin$channel$in$order$to$release$any$jammed$coins,$as$shown$below.$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
5.3$Error$messages$
When$the$CS20$is$turned$on$it$will$undergo$a$self[test.$If$the$CS20$detects$a$fault$it$will$
display$one$of$the$following$error$messages:$
$
7B:$This$means$the$coin$sensor$is$impeded.$To$unblock$the$coin$sensor:$turn$off$the$machine$
and$disconnect$the$power$supply,$then$open$up$the$back$cover.$Turn$the$sorting$disc$by$
hand$until$you$can$see$the$coin$sensor$in$the$top$left$corner,$as$shown$below.$Remove$any$
dust$or$dirt$on$the$sensor.$ $
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$

ZZap$CS20$Coin$Counter$and$Sorter$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$ $ $ $
6$
In$the$event$that$“EA”$is$often$displayed,$it$may$be$necessary$to$clean$the$inside$of$the$
machine:$
1) Switch$off$the$machine$and$disconnect$the$power$supply.$
2) Unscrew$and$remove$the$3$screws$near$the$bottom$of$the$cover.$
3) Remove$the$cover$and$clean$the$coin$sensor,$sorting$disc$and$back$plate$with$a$brush$
or$cloth.$Remove$foreign$coins/objects.$
$
7-C7DE'This$means$a$counting$sensor$is$impeded.$There$are$2$counting$sensors$located$at$the$
top$of$each$coin$channel.$E1$indicates$the$coin$channel$with$the$smallest$diameter$is$
impeded;$E8$has$the$largest$coin$channel$diameter.$
$
To$unblock$the$counting$sensors:$remove$any$coins$that$have$become$jammed$in$the$coin$
channel,$see$5.2$and$clean$both$counting$sensors$with$a$brush$or$cloth.$ $
$
7F:$This$means$the$speed$sensor$is$impeded.$To$unblock$the$speed$sensor$follow$the$steps$
below:$
1) Switch$off$the$machine$and$disconnect$the$power$supply.$
2) Unscrew$and$remove$the$3$screws$near$the$bottom$of$the$cover.$
3) Remove$the$cover$and$clean$the$speed$sensor$with$a$soft$cloth.$The$speed$sensor$is$
located$on$the$right$hand$side,$just$above$the$sorting$disc.$ $
@.'/;#&1$1&%+1)*,'
•Operating$temperature$range:$0$~$40°C.$
•Operating$humidity$range:$30$~$80%.$
•Hopper$capacity:$Max.$500$coins.$
•Coin$tray$capacity:$Max.$300$coins.$
•Denomination$display:$3$digit$LED$
•Counting$number$display:$4$digit$LED$
•Power$source:$AC220[240V/50Hz$or$AC110V/60Hz$
•Power$consumption:$<20W$
•Dimensions:$345$x$306$x$260$mm$
•Net$weight:$3.2$KG$
•Counting$speed:$Max.$220$coins/minute$
$
If$the$machine$has$a$fault$that$you$are$unable$to$resolve,$please$contact$your$local$ZZap$
dealer.$
$
Products$are$subject$to$change$without$further$notice.$
$
$
$