1 BY ONE 471NA-0010 User manual

Turntable Hi-Fi System with Speakers
Instruction Manual

1
Introduction
Thank you for purchasing 1byone Turntable Hi-Fi System with Speakers. This
instruction manual contains important information about safety, usage and disposal.
Use the product as described and keep this manual for future reference. If you sell this
turntable or pass it on, also give this manual to the new owner.
Safety Instructions
Read and understand this entire manual before using this product. Keep these
instructions for future reference.
1. Do not use the turntable near water.
2. Only connect the turntable to a power outlet type as indicated on the marking
label or in the "Specifications" section of this instruction manual.
3. The turntable has a polarized plug (one pin is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit into a polarized outlet in only one
orientation. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to modify the plug in
any way.
4. Protect the power cord from being walked on or pinched, particularly at the power
plug, at the point of connection between the plug and outlet and at the point of
connection between the power cable and speaker.
5. Do not overload wall outlets or extension cords as this will be a fire hazard and may
cause electric shock.
6. Never push objects of any kind into the turntable through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
7. Do not attempt to service the turntable yourself as opening or removing body
panels may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
8. Changes or modifications to the turntable not expressly approved by the party
responsible for compliance could void the user’s authority to operate the product.
9. Do not use attachments not recommended by the manufacturer as they may cause
hazards.
10. Only place on a flat, sturdy table or use with the cart, stand, tripod or
bracket as specified by the manufacturer or sold with the turntable.
When a cart is used, use caution when moving the cart/turntable
combination to avoid injury from tip-over.

2
11. Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating. Do not block
or cover these openings.
12. Unplug the product during lightning storms or when unused for long periods of
time.
COMPLIANCE WITH FCC REGULATIONS
This device complies with Part 15 of FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
WARNING: Cancer and Reproductive Harm - HYPERLINK "http://www.
P65Warnings.ca.gov."
For more information go to HYPERLINK "http://www.1byonebros.com/
Compliance/Prop65"

3
Product Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2425
23
19
22
2016
17 21
18
1. Motor Pulley
2. Drive Belt
3. Turntable Spindle
4. Turntable Sub-platter
5. Turntable Platter
6. Lid Hinges
7. Counterweight
8. Tonearm Lift Lever
9. Tonearm Rest & Clip
10. Volume Control
11. Tonearm
12. 33/45 RPM Selector
13. Function Knob
14. Play/Stop Button
15. Stylus Cartridge
16. Ground Connector
17. Phono & Line Out Jacks
18. Phono & Line Out Switch
19. USB Port for PC Link
20. Power Cord Jack
21. Pitch Adjustment Screws
22. External Speaker Jacks
23. Power Switch
24. Speaker Jack -
25. Speaker Jack +

4
Included Items
Before installing the turntable, check the package contents to ensure all parts below
are included and free of visible damage. Please retain the original packaging materials
for exchange or return purposes.
1 x Turntable Unit
2 x Speakers
1 x Turntable Lid
1 x Slip Mat
1 x Turntable Platter
1 x Tonearm Counterweight
1 x 45 RPM Adapter
1 x Drive Belt
1 x Sub-platter
1 x Power Adapter
1 x USB Cable for PC Link
2 x Audio Cables for Speakers
1 x Cartridge Alignment Protractor
1 x Instruction Manual
Installing the Turntable
• Place or mount the turntable on a level surface.
• To avoid the effects of vibrations and acoustic pressure if the turntable is being
securely mounted with screws, do not mount directly next to speakers.
• The turntable may pick up radio static if placed next to a radio. Therefore, try to keep
the turntable away from radios.
• If the turntable is near equipment (cell phone, etc.) that emits strong radio waves,
noise may occur.
Installing the Lid
Insert the hinge pockets of the lid onto the hinges of
the turntable.

5
Turntable Platter and Belt Setup
1. Remove the protective packaging and ensure the turntable is placed on a sturdy
and level surface.
2. Insert the sub-platter into the turntable spindle located in the middle of the
turntable.
3. Loop the drive belt around the sub-platter and motor pulley (brass-colored).
4. Rotate the Sub-Platter.
1) Using your hands, slowly rotate the sub-platter ten times in a clockwise direction.
2) This step is for resetting the auto mechanism, getting rid of any twists in the belt
and making sure the belt rides smoothly along the drive rim on the underside of
the platter.

5. Carefully place the main platter onto the sub-platter.

6
6. Place the slip mat on top of the platter. Make sure the 1byone logo on the mat is
facing up.
Cartridge Tracking Force Adjustment
1. Gently push the counterweight onto the rear of the tonearm.
2. Carefully push and pull the Counterweight and stop when it reaches the tick mark
of recommended tracking force.
TonearmCounterweight
Note: Each mark on the dial represents 0.5g. The recommended tracking force for
the factory-installed cartridge is 2.5g±0.5g.

7
3. If the counterweight loosens or moves during the usage, please gently turn the
screw to make it tight again.
Connecting to Speakers
1. Connection to the Included Speakers
This turntable includes a built-in preamp and comes supplied with Hi-Fi speakers.
Connect the speakers using the included audio cable (black cable to black cable
clamp and red cable to red cable clamp).
2. Connection to External Speaker with the RCA Audio Cable
If you wish to use your own amplifier or speakers, please follow the instructions
below:
RCA wired connection
Active Speakers
or
Amplifier

8
2.1 Setting pre-amplier selector switch
This product has a built-in phono equalizer function. You can use the product
even if you do not have a phono amplifier or connectable equipment with a
built-in phono amplifier.
Use the pre-amplifier selector switch to set the output, as shown below.
Connectable equipment
being used
Position of pre-amplifier
selector switch
Where to connect RCA
audio cable
Device with phono input PHONO Phono input jack and
ground (earth) terminal of
connectable equipment
Device without phono
input
LINE AUX or line input jack of
connectable equipment
When connecting via the included speakers, using the pre-amplifier selector
switch is not necessary.
NOTE: The RCA Jacks are not designed to be connected directly to the
passive/unpowered speakers on LINE mode. If connected to the passive
speakers, there will be no sound.

9
2.2 Connecting the device
Align the settings for the pre-amplifier selector switch and connect the
RCA audio cable to an input jack that is compatible with the connectable
equipment you are using (amplifier, active speakers, etc.).
• The RCA audio cable's red jack is for the right (R) channel, and the white jack is
for the left (L) channel.
AUX
L R
PHONO
L R
With PHONO Without PHONO
To outlet
Connectable equipment
(Amplifier, etc.)
With PHONO Without PHONO
To outlet

10
Main Power Connection
1. Insert the DC plug of the AC adapter cord into the DC INPUT Jack at the back of the
turntable.
2. Plug the AC adapter into a normal power outlet.
NOTE: Do not plug the AC power adapter into a power outlet before all turntable
assembly is completed. Before turning on turntable power, recheck all connections to
make sure they are correct and secure. Always turn off the turntable before connecting
or disconnecting from power.
Playing a Record
1. Before playing a record
1.1 Pull the protector straight forward to remove it.
NOTE: Applying a downward force may
cause the stylus to come off the body. Only
low volume will be output if the stylus has
come off, or is about to come off, so refer to
“Replacing the stylus”to reattach the stylus
correctly.
Protector

1.2 Place the record on the felt mat so that the center hole aligns with the spindle.
45 RPM Adapter
If playing a 45 RPM record with a large center hole, attach the 45 RPM adapter.

11
2. Turntable Operation
Sufficiently lower the volume of the amplifier, speakers, etc.
2.1 Connect the included power adapter to the turntable and slide the Power Switch to
the “ON” position.
2.2 Remove the stylus protector from the stylus.
2.3 Place the record on the slip mat. If using 45RPM records, put the 45RPM adapter on
the center spindle before placing the record on the platter.
2.4 Rotate the 33/45 RPM Selector according to the type of record.
2.5 Rotate the Function Knob to LP, press the Play/Stop Button. The
platter will start spinning.
2.6 Unlock the tonearm clip and set the tonearm lift lever to the up
position.
45RPM Adapter
2.7 Position the tonearm over the desired location (groove) on the record.
2.8 Carefully lower the tonearm on the record.
2.9 Turn up the volume of the turntable as needed.
2.10 When you are finished playing the record, set the tonearm lift lever to the up
position, raise the tonearm and return it to rest on the arm clip. Press the Play/Stop
button to stop.
NOTE:
1. If the silent pause time between each track is longer than 3 minutes, the platter
will stop spinning automatically to avoid damaging the record. This stoppage does
not mean the turntable is defective.
2. If the felt mat gets dirty, it can easily scratch the record, so remove the felt mat
periodically and wipe off any dust.
3. To prevent the record from scratches and warping, remove it after use.
4. Do not use a disk stabilizer.

12
Wireless Operation
T his appliance is equipped with Bluetooth (TX and RX mode). TX mode allows this
turntable to wirelessly transmit audio to your Bluetooth speaker or headphone. In RX
mode, you can connect your media device to this turntable and play music through it.
1. TX Mode
1.1 Power on your Bluetooth speaker or headphone and ensure it's in pairing mode.
1.2 Power on the turntable. Rotate the Function Knob to TX. The blue indicator light
under TX will turn on.
1.3 When pairing, the light will flash twice per second and will become solid when
paired successfully.
1.4 This turntable will connect to the nearest Bluetooth speaker. If you need to connect
again, rotate the Function Knob to LP, and then rotate it to TX to start over.
2. RX Mode
2.1 Rotate the Function Knob to RX. The blue indicator light under RX will turn on.
2.2 Turn on the Bluetooth feature of your media device and search for and select
"BT10-music" to pair the media device and turntable.
2.3 Once your media device is successfully paired with the turntable, the turntable
will play a short confirmation sound. Stream music from your media device to the
turntable.
NOTE:
1. The Play/Stop button can only control the operation of the platter. To control
music streaming through Bluetooth, please use the control panel of your media
device.
2. Bluetooth version: 5.0
Recording the Vinyl to Your Computer
Please follow the below steps to set up Audacity to record from the USB audio device.
For more details, please refer to the BRIEF INTRODUCTION OF AUDACITY at https://
manual.audacityteam.org/man/recording_with_usb_turntables.html
Please notice that the turntable's USB-PC recording function is only available
in LP mode and does not work in Bluetooth mode.
1. Download the Audacity software and complete installation
1.1 Ensure your Audacity software is up to date. You can download the current
version from http://www.audacityteam.org/download/
1.2 Follow the instructions to complete installation.

13
2. Set up Audacity to record from the USB audio device.
2.1 Connect the USB device
Use the supplied USB cable to connect your turntable and your computer. No
extra driver is required.
2.2 System settings needed for Windows and Mac
Windows:
1. By the system clock, right-click over the Speaker icon select Sounds then
the Recording tab, and then click on the USB device in the list and click
Properties. Click the Advanced tab set your required bit rate and sample rate
from the Default Format dropdown (normally "2 channel 16-bit 44100 Hz").
2. On the Advanced tab, in the "Default Format" section, make sure the
dropdown menu is set to "2 channel 16-bit 44100 Hz".
For a more detailed walk-through of the above steps for Windows (
or if that does
not work for your version of Windows ), see Windows: accessing the Windows
Sound controls.
Mac:
1.
From Apple Menu > System Preferences select "Sound" and click on the Input
tab
2. Select "USB Audio CODEC" or similar as the input device and verify the
Recording Meter shows input.
3. If the recording meter in the Sound preferences panel does not show input:
1. From the Finder, select Go > Utilities and open Audio MIDI Setup.
2. If the
Audio Devices window is not visible, select Window > Show Audio
Devices.
3. Select your USB input device in the list in the left pane of the Audio Devices
window.
4. Set the Format to "44100.0 Hz" and "2ch-16bit".
For a more detailed walk-through of the above steps for Mac
, see Mac and USB
input devices on the Audacity Wiki.
2.3 Launch Audacity.
If Audacity is already running when you connected the cable, choose Transport
>Rescan Audio Devices or restart Audacity.
2.4 Project Rate
Set the Audacity Project Rate in Selection Toolbar at the bottom left of the
Audacity screen to 44100 Hz :

14
2.5 Devices
Use Device Toolbar to set the recording and playback devices and to set the
recording channels to "2 (Stereo) Recording Channels", as in the below example on
Windows 10:
• The Recording Device is set to the USB device (in this case the device name, but
often called or including the phrase "USB Audio CODEC").
• Recording Channels is set to stereo.
• The Playback Device is set to the named speakers of the built-in computer sound
device.
• These settings can also be changed in Devices Preferences.
Windows calls most USB external devices "microphones". Some higher-end USB
recording interfaces may appear as their explicit manufacturer's name.
3. Software Playthrough
Use Transport > Transport Options > Software Playthrough (on/o) and click
"Software Playthrough" to turn it "on" (the checkmark is shown when it is "on").
This setting can also be enabled or disabled in Recording Preferences. Software
Playthrough lets you hear the turntable through the computer speakers when
recording. It also lets you hear the turntable
without recording if you turn on
monitoring (see the next section below).
4. Monitoring
Enable monitoring to set the recording level
• Turn monitoring on by clicking once on the microphone icon in the Recording
Meter.
• In Mixer Toolbar, turn up the left-hand playback volume slider (by the speaker icon).
• The right-hand recording volume slider (by the microphone icon) can often be used
to vary the loudness of the recording, but it may not function with all turntables.
If it does not, try adjusting the output level on the turntable (often, there is a gain
control under the chassis).
Alternatively, you may be able to adjust the input level on Windows and Linux only,
usually by looking for the speaker icon by the system clock. On Windows,right-
click over the speaker icon > "Recording Devices". Then right-click over USB
Audio Codec, choose "Properties" and click the Levels tab.

15
• Try to aim for a maximum peak of around –6 dB, which corresponds to
around 0.5 on the waveform. You can always boost the level later with Eect
>Amplify... or Eect >Normalize... after you have completed editing.
5. Recording
Then, ignoring any instructions in the manufacturer's guide to select "stereo mix",
simply press the Record button in Transport Toolbar to start recording from the
turntable.
6. Recording, editing and exporting
Once your USB turntable is set up and working properly, go to the Basic Recording,
Editing and Exporting section of Audacity’s Tutorial - Copying tapes, LPs or
MiniDiscs to CD for instructions on how to:
• make and edit your recording
• export it to an audio file
• import it to iTunes or Windows Media Player
• burn it to CD
Audacity’s reference links:
•Basic Recording, Editing and Exporting: https://manual.audacityteam.org/man/
basic_recording_editing_and_exporting.html
•Tutorial - Copying tapes, LPs or MiniDiscs to CD : https://manual.audacityteam.
org/man/tutorial_copying_tapes_lps_or_minidiscs_to_cd.html
Care
Turntable Body
• When the turntable body is dirty or dusty, first disconnect the AC adapter and then
wipe off the dirt and dust with a soft, dry cloth.
• Do not use benzenes, thinners, etc.
• When storing the product for a long time, disconnect the AC adapter from the
outlet and wrap the product in plastic; do not allow it to become damp; the drive
belt should be removed to prevent unequal stretching.
Tips for Stylus Cleaning
• If dirt and grime are stuck to the stylus tip, clean it
with a commercially sold brush.
• We recommend using a stylus cleaner (not
included) if the stylus tip is considerably dirty.
Clean the stylus tip by moving the brush from the
rear to the front of the stylus tip.

16
Replacing the Stylus
It's suggested to replace the stylus after 400 hours of use.
Removing the Stylus
• In addition to the deterioration of sound quality, records may also be damaged as
the cartridge’s stylus tip wears down.
• Be sure to disconnect the product’s AC adapter from the outlet.
• When replacing the stylus, hold the headshell and the cartridge body tightly.
Rotate the front of the stylus in a forward and down motion.
Installing a New Replacement Stylus
1. Mount the new replacement stylus to the cartridge.
Engage in body first
2. Lift the stylus up until you hear a click.
3. Make sure there is no gap between the headshell and the cartridge.

17
Replacing the Belt
• The belt is a consumable part. Replace the belt if the speed of playback slows down
or irregular rotation occurs. As a rule of thumb, we suggest replacing the belt once a
year.
• Before replacing the belt, be sure to disconnect the product’s AC adapter from the
outlet.
1. Remove the slip mat.
2. Remove the main platter and then remove the old belt.
3. Loop the new belt around the sub-platter and motor pulley.

18
4. Using your hands, slowly rotate the platter ten times in the direction of the
arrow.

5. Place the main platter back onto the sub-platter.
Cartridge Replacement
1. Before replacement, put the stylus protector back on the stylus to prevent damage
to the stylus during the replacement process.
2. Carefully remove the wire leads from the original cartridge.
3. Loosen the two screws on the headshell that are securing the cartridge and then
remove the original cartridge.
4. Mount the new cartridge to the headshell and tighten it lightly. Do not completely
tighten the screws at this moment.

19
5. Connect the wire leads to the new cartridge’s terminals .The wire lead color codes
are as below:
Wire Channel
White Left channel positive (L+)
Black Left channel negative (L–)
Red Right channel positive (R+)
Black Right channel negative (R-)
6. Adjust the cartridge’s position to make sure it is precisely aligned on the headshell
so that the stylus will be appropriately tracking within the grooves.
To achieve this, place the included paper cartridge alignment protractor over the
turntable spindle, carefully lift the tone arm, and place the tip of the stylus on the
points marked 130mm and 250mm respectively. Fine tune the cartridge’s position
on the headshell until the cartridge is perfectly in parallel with the reference lines at
both points.
7. Tighten the screws completely once perfect alignment is achieved.
NOTE: If you are unfamiliar or uncomfortable with completing this procedure, we
recommend consulting with a professional to perform the installation.
When the Turntable is Moved
Using the product's original packing materials, wrap the turntable in the reverse order
from when you unwrapped it. If you do not have the packaging materials, take the
following measures:
• After disconnecting the AC adapter from the outlet, remove the felt mat and platter,
and then wrap them so that they do not get damaged.
• Attach the protector to the cartridge.
• Use a string or something similar to tie the tonearm to the rest so that it does not
become dislodged.
• Wrap the turntable body with paper or a soft cloth so that it does not get damaged.