3Com LSBM1SRP1M1 User manual

H3C S9500 Series Routing Switches
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08048T-20071015-C-1.24
Product Version: S9500-CMW310-R1632P03

Copyright © 2006-2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
[e-mail]
http://www. h3c.com

About This Manual
Related Documentation
The related manuals are listed in the following table.
Manual Description
H3C S9500 Series Routing
Switches Operation Manual
It provides an operation guide. It consists of access
volume, IP service volume, IP routing volume, IP
multicast volume, MPLS/VPN volume, QoS/ACL
volume, security volume, system volume, and
acronyms.
H3C S9500 Series Routing
Switches Command Manual
It explains all commands available in the S9500
series and provides a list of commands the S9500
series do not support. It consists of the same
modules as the operation manual.
Organization
H3C S9500 Series Routing Switches Installation Manual is organized as follows:
Chapter Contents
1 Product Overview Introduces the appearance, architecture
and system features of the S9500
series.
2 Installation Preparations Lists the preparations and precautions
for the installation.
3 Switch Installation Details the installation of the chassis, PSUs, boards and cable connection for
the S9500 series.
4 System Commissioning Concentrates on the initial power-on and
booting of the S9500 series.
5 Switch Monitoring and Maintenance Presents the hardware and software
upgrade.
6 Appendix A Cable Management Introduces how to bind cables.
7 Appendix B Engineering Labels for
Cables Introduces the use of engineering labels.

Chapter Contents
8 Appendix C Installation of Lightning
Arrester for AC Power
Introduces the installation of lightning
arrester for AC power of S9500 series
routing switches.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
&<1-n> The argument(s) before the ampersand (&) sign can be
entered 1 to n times.
# A line starting with the # sign is comments.
II. GUI conventions
Convention Description
< > Button names are inside angle brackets. For example, click
<OK>.
[ ] Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/ Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].

III. Symbols
Convention Description
Warning Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.
Environmental Protection
This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.

Installation Manual
H3C S9500 Series Routing Switches Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................................................................1-1
1.1 Introduction........................................................................................................................1-1
1.2 Physical Structure..............................................................................................................1-1
1.2.1 Chassis and Slots ...................................................................................................1-2
1.2.2 Backplane................................................................................................................1-6
1.2.3 Power System.........................................................................................................1-7
1.2.4 PoE Power Supply..................................................................................................1-9
1.2.5 Fan Tray................................................................................................................1-12
1.3 Switching and Routing Processing Unit...........................................................................1-13
1.4 Line Processing Unit........................................................................................................1-14
1.5 Service Board ..................................................................................................................1-16
1.6 System Specifications......................................................................................................1-16

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-1
Chapter 1 Product Overview
1.1 Introduction
The S9500 Series Routing Switches (hereinafter referred to as the S9500 series) are
developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to as H3C)
for use on business-oriented enterprise networks, the distribution layer of large MANs,
the core layer of small MANs, and the backbone of large enterprise networks and
campus networks. They can serve as switching cores and convergence centers.
Currently, the S9500 series consist of the following models:
zS9502: This model provides a switching capacity of up to 240 Gbps. It allows for
the concurrent wire-speed forwarding on 96 GE ports, or 8 × 10 GE ports, or 144
FE electrical ports, or 60 FE optical ports.
zS9505: This model provides a switching capacity of up to 600 Gbps. It allows for
the concurrent wire-speed forwarding on 240 GE ports, 20 × 10GE ports, 240 FE
electrical ports, or 100 FE optical ports.
zS9508: This model provides a switching capacity of up to 960 Gbps. It allows for
the concurrent wire-speed forwarding on 384 GE ports, 32 × 10GE ports, 384 FE
electrical ports, or 160 FE optical ports.
zS9508V: This model provides a switching capacity of up to 960 Gbps. It allow for
the concurrent wire-speed forwarding on 384 GE ports, 32 × 10GE ports, 384 FE
electrical ports, or 160 FE optical ports. This model adopts upright slots.
zS9512: This model provides a switching capacity of up to 1.44 Tbps. It allows for
the concurrent wire-speed forwarding on 576 GE ports, 48 × 10GE ports, 576 FE
electrical ports, or 240 FE optical ports.
Note:
Unless otherwise specified in this document, the S9508V and the S9508 have the
same configuration.
1.2 Physical Structure
The S9500 series use integrated chassis, which consists of a power area, board area,
backplane, and fan area.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-2
Note:
zTwo switching and routing processor units (SRPUs) can be installed on the S9500
series to support active-standby switchover.
zTwo power supply units (PSUs) can be installed on the S9500 series to provide
hot-standby 1+1 redundancy.
zThe S9500 series support PoE and an external PoE power supply is optional.
zBoards, fan tray, and AC/DC PSUs are hot-swappable.
1.2.1 Chassis and Slots
I. S9502
(1) SRPU slot (2) SRPU/LPU slot (3) LPU slots
(4) PSUs (5) Fan tray
Figure 1-1 Front view of the S9502
zThe S9502 chassis provides four slots in its board area: from up to down, the first
one accommodates an SRPU, the second one accommodates an SRPU or a line
processing unit (LPU), and the remaining two slots accommodate LPUs or service
boards.
zAt the bottom of the chassis is the power area that contains two power supply units
(PSUs). The switch supports both AC and DC power inputs. So you can select AC
or DC PSUs as needed. A PoE filter at the rear of the chassis is used to receive
power from an external PoE power supply.
zOn the right of the chassis is the fan area that contains a vertical fan tray. The fans
draw air in from the left and exhausts air from the right.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-3
II. S9505
(1) SRPU slots (2) LPU slots (3) Cable management bracket
(4) PSUs (5) PoE power entry module (6) Fan tray
Figure 1-2 Front view of the S9505
zThe S9505 chassis provides seven slots in its board area: The top two
accommodate SRPUs, which can operate in 1+1 redundancy mode; the remaining
five accommodate LPUs/service boards.
zAt the bottom of the chassis is the power area that contains one PoE entry module
and two PSUs. The two PSUs arehot-swappable; they can operate in 1+1
redundancy mode. The switchsupports both AC and DC power inputs. So you can
select AC or DC PSUs as needed.
zOn the right of the chassis is the fan area that contains one vertical fan tray. The
fans draw air in from the left and exhausts air from the right.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-4
III. S9508
(1) LPU slots (2) SRPU slots (3) PSUs
(4) PoE power entry module (5) Fan tray
Figure 1-3 Front view of the S9508
zThe S9508 chassis provides ten slots in its board area: The middle two
accommodate SRPU modules; the remaining eight accommodate LPUs/service
boards.
zAt the bottom of the chassis is the power area that contains one PoE power entry
module and two PSUs. The switch supports both ACand DC power inputs. So you
can select AC or DC PSUs as needed.
zOn the right of the chassis is the fan area that contains one vertical fan tray. The
fans draw air in from the left and exhausts air from the right.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-5
IV. S9508V
(1) Fan tray (2) LPU slots (3) SRPU slots
(4) Air filter (5) PSUs (6) PoE power entry module
Figure 1-4 Front view of the S9508V
zThe S9508V chassis provides ten vertical slots in its board area: The middle two
accommodate SRPU modules; the remaining eight accommodate LPU/service
boards.
zAt the bottom of the chassis is the power area that contains one PoE power entry
module and two PSUs. The switch supports both ACand DC power inputs. So you
can select AC or DC PSUs as needed.
zAbove the power area is the air filter, which can be removed from the chassis in
the case of replacement or regular cleaning.
zOn the top of the chassis is the fan area that contains one horizontal fan tray. The
fans draw air in from the bottom and exhaust air from the top.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-6
V. S9512
(1) LPU slots (2) SRPU slots (3) PSUs
(4) PoE power entry module (5) Fan trays
Figure 1-5 Front view of the S9512
zThe S9512 chassis provides fourteen slots in its board area: The middle two
accommodate SRPU modules and the remaining twelve accommodate
LPUs/service boards.
zAt the bottom of the chassis is the power area that contains one PoE entry module
and two PSUs. The switch supports both AC and DC power inputs. So you can
select AC or DC PSUs as needed.
zOn the right of the chassis is the fan area that contains two vertical fan trays. The
fans draw air in from the left and exhaust air from the right.
1.2.2 Backplane
The backplane of the S9500 series allows high-speed data exchange between SRPUs
and LPUs, as well as the exchange of various management and control signals in the
system.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-7
I. Functions
The following are the main functions of the backplane:
zProviding communication channels for signal exchange between boards
zSupporting board hot-swapping
zSupporting board auto-discovery in slots
zConnecting PSUs to distribute power SRPUs, LPUs/service boards, and fan tray(s)
and providing monitor channels for them.
II. Structure
The S9500 series use a passive backplane, which provides multiple boardslots, one or
two fan interfaces, and two –48V power interfaces (one for PSUs and the other for PoE
power entry module).
1.2.3 Power System
Note:
zThe S9500 series support both AC and DC power inputs. So you can choose AC or
DC PSUs as needed.
zThe S9500 series support 1+1 power supply redundancy.
zThe PSUs of the S9500 series are hot-swappable.
The power system is at the bottom of thechassis. In the PSU slots, you can inserteither
two AC PSUs or two DC PSUs. The PSUs are cooled by the built-in fans, which draw
air into the chassis from the front and exhaust air from the rear.
zAC PSU
Table 1-1 Specifications for AC PSUs
Specifications
Item NEPS600-A NEPS1200-A NEPS2000-A NEPS3500-A
Model S9502 S9505 S9508/S9512 S9508/S9512
Rated
voltage
range
100 to 240 VAC,
50 Hz or 60 Hz 100 to 240 VAC, 50 Hz or 60 Hz
100 to 120 VAC,
60 Hz
200 to 240 VAC,
50 Hz
100 to 240 VAC,
50 Hz or 60 Hz
Input
voltage
range
90 to 264 VAC,
50 Hz or 60 Hz 90 to 264 VAC, 50 Hz or 60 Hz 90 to 264 VAC, 50 Hz or 60 Hz 90 to 264 VAC, 50 Hz or 60 Hz

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-8
Specifications
Item NEPS600-A NEPS1200-A NEPS2000-A NEPS3500-A
Max
input
current 7.5 A 15 A 15 A
Single 1800 W
sub-PSU :15 A
Two 1800W
sub-PSUs: 30 A
Table 1-2 Configuration and output power of AC PSUs
PSU Configuration Maximum output
power
NEPS600-A 1 ×NEPS600-A, no redundancy
2 ×NEPS600-A, 1+1 redundancy 600 W (90 V to 264 V)
NEPS1200-A 1 × NEPS1200-A, no redundancy
2 × NEPS1200-A, 1+1 redundancy 1200 W (90 V to 264 V)
NEPS2000-A 1 × NEPS2000-A, no redundancy
2 × NEPS2000-A, 1+1 redundancy 1200 W (90 V to 160 V) 2000 W (160 V to 264 V)
1 × NEPS3500-A enclosure + 1 ×
sub-PSU, no redundancy
1 × NEPS3500-A enclosure + 2 ×
sub-PSU, 1+1 redundancy
1200 W (90 V to 180 V)
1800 W (180 V to 264 V)
1 × NEPS3500-A enclosure + 2 ×
sub-PSU, no redundancy
2 × NEPS3500-A enclosure + 3 ×
sub-PSU, 2+1 redundancy
2 × NEPS3500-A enclosure + 4 ×
sub-PSU, 2+2 redundancy backup
2400 W (90 V to 180 V)
3500 W (180 V to 264 V)
NEPS3500-A
2 × NEPS3500-A enclosure + 3 ×
sub-PSU, no redundancy
2 × NEPS3500-A enclosure + 4 ×
sub-PSU, 3+1 redundancy
3500 W (90 V to 180 V)
zDC PSU
Table 1-3 Specifications for DC PSUs
Specifications
Item NEPS600-D NEPS1200-D NEPS2000-D NEPS3500-D
Model S9502 S9505 S9508/S9512 S9508/S9512
Rated
voltage
range
–48 to –60
VDC –48 to –60 VDC –48 to –60 VDC –48 to –60 VDC

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-9
Specifications
Item NEPS600-D NEPS1200-D NEPS2000-D NEPS3500-D
Input
voltage
range
–36 to –72
VDC –36 to –72 VDC –36 to –72 VDC –36 to –72 VDC
Max
input
current 12.5 A 25 A 42 A 75 A
Max
output
power 600 W 1,200 W 2,000 W 3,500 W
1.2.4 PoE Power Supply
The S9500 series support power over Ethernet (PoE). With this feature, an S9500
switch equipped with an external PoE power supply and PoE-capable LPUs can deliver
–48 VDC to its remotely powered devices (PDs), such as IP phones, wireless LAN
(WLAN) access points (APs) and network cameras, through Ethernet cables.
Currently, among the LPUs of the S9500 series, only GV48 is PoE capable.
zThe S9500 series can supply power to remote PDs through Ethernet electrical
ports on the LPUs. Each LPU can simultaneously supply power to up to 48 PDs
with the maximum distance of 100 m (328.1 feet).
zEach Ethernet port can deliver up to 15.4 W to its PD.
zThe S9500 series determine whether to deliver power to a newly detected PD
according to the following condition: If the remaining PoE power of the switch is
greater than what is required by anewly detected PD, the switch supplies power to
it. Otherwise, the switch does not supply power to it.
I. PoE power entry module
The PoE-supported S9505/S9508/S9508V/S9512 switch chassis has a PoE power
entry module between the two PSUs. You can connect this PoE power entry module to
an external PoE power supply PSE4500-A.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-10
Figure 1-6 PoE power entry module
II. External PoE power supply
The following two types of external PoE power supplies are available for the S9500
series:
zPSE4500-A
It is applicable to the S9505/S9508/S9508V/S9512. Figure 1-8 shows the PSE4500-A
front panel.
Figure 1-7 PSE4500-A front panel
Table 1-4 describes typical equipment configurations and specifications of PSE4500-A.
Table 1-4 Typical equipment configurations and specifications of PSE4500-A
Item Specifications
Physical dimensions (H ×W ×D) 175 × 482.6 × 320.5 mm (6.89 ×19.00 ×12.62
in.)
System controller One
Rectifiers (NP2500UAC) Two NP2500UACs (required) + one redundant NP2500UAC (optional); NP2500UAC is
hot-swappable

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-11
Item Specifications
AC accessories Three AC inputs and switches Three AC voltage detection circuits
Input voltage range: 90 to 264 VAC
DC accessories A single DC output, with a max output power of
4500 W (220 V)/2400 W (110 V)
zPSE2500-A1
It is applicable to the S9502.
Figure 1-8 shows the PSE2500-A1 front panel.
Figure 1-8 PSE2500-A1 front panel
Table 1-5 describes typical equipment configurations and specifications of
PSE2500-A1.
Table 1-5 Typical equipment configurations and specifications of PSE2500-A1
Item Description
Physical dimensions (H ×W ×D) 175 × 486 × 380 mm (6.89 ×19.13 ×14.96 in.)
System controller One
Rectifiers (NP2500UAC) One NP2500UAC (required) + one redundant
NP2500UAC (optional); NP2500UAC is
hot-swappable
AC accessories Three AC inputs and switches Three AC voltage detection circuits
Input voltage range: 90 to 264 VAC
DC accessories A single DC output, with a max output power of
2500 W (220 V)/1200 W (110 V)
The external PoE power system has the monitoring function. It provides one RS232
and two RS485 monitoring interfaces. The external PoE power supply can display
alarm information through the ALM LED. The system can learn the running information

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-12
of the rectifiers by connecting a monitoring port to the SRPU. You can use cables to
connect the monitoring ports from the front or the rear of the external PoE power
supply.
Note:
The external PoE power system for the S9500 series only support RS485 monitoring
ports.
Table 1-6 LEDs of external PoE power system
LED Label Color Normal
state Abnormal state Abnormal reason
Input power
LED AC Green ON OFF Loss of AC input power, or blown fuse
Output
power LED DC Green ON OFF No DC output from PSU
Fault LED Fault Red OFF ON Irreversible fault
occurred in PSU
Running
status LED RUN Green ON OFF PSU shutdown or PSU running trouble
Alarm LED ALM Red OFF ON
Loss of AC input
power, under-voltage
or over-voltage input,
over-voltage output,
output short-circuit,
or PSU fault
1.2.5 Fan Tray
zThe S9502 uses one 36 W fan tray, which contains eight 70 × 70 × 25.4 mm (2.8 ×
2.8 × 1.0 in.) DC fan units.
zThe S9505 uses one 25 W fan tray, which contains four 120 × 120 × 25.4 mm (4.7
× 4.7 × 1.0 in.) DC fan units.
zThe S9508 uses one 35 W fan tray, which contains six 120 × 120 × 25.4 mm (4.7 ×
4.7 × 1.0 in.) DC fan units.
zThe S9508V uses one 70 W fan tray, which contains six 120× 120 × 38 mm (4.7 ×
4.7 × 1.5 in.) DC fan units.
zThe S9512 uses two 25 W fan trays, each of which contains four 120 × 120 × 25.4
mm (4.7 × 4.7 × 1.0 in.) DC fan units.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-13
The fans of S9502 switches operate at 12 VDC supplied from the fan monitor board,
while the fans of the S9505/S9508/S9508V/S9512 operate at –48 VDC supplied from
the backplane.
Figure 1-9 Fan tray panel of the S9502/S9505/S9508/S9512
Figure 1-10 Fan tray panel of the S9508V
Table 1-7 LEDs on fan tray panel
LED Color Status Meaning
OFF The fan tray is faulty.
RUN Green
ON The fan tray is operating normally.
OFF The fan tray is operating normally.
ALM Red ON The fan tray is faulty.
1.3 Switching and Routing Processing Unit
SRPUs serve as the core of the S9500 series. They mainly have the following
functions:
zRoute calculation and forwarding table maintenance.
zIntegrating crossbar switching fabric to accomplish service exchange between
different boards.

Installation Manual
H3C S9500 Series Routing Switches Chapter 1 Product Overview
1-14
zProviding system configuration and monitoring functions, which allows the system
to monitor other boards and upgrade/reset service board software.
The following table lists the SRPUs applicable to the S9500 series.
Table 1-8 SRPUs applicable to the S9500 series
SRPU S9502 S9505 S9508 S9508V S9512
LSB1SRP1M1 9
LSB1SRP1N4 9
LSB1SRP1N5 99
LSB1SRP1N6 9
LSB1SRP1N7 9999
LSB1SRP2N4 9
LSB1SRP2N5 99
LSB1SRP2N6 9
LSB1SRP2N7 9999
LSB2SRP1N4 9
LSB2SRP1N5 99
LSB2SRP1N6 9
LSB2SRP1N7 9999
Note:
The tick 9indicates that the SRPU is applicable to the switch. SRP2N’s forwarding
capacity is twice the SRP1N’s.
1.4 Line Processing Unit
The following LPUs are available:
Table 1-9 LPUs available
LPU Suffix User interface
LSB1XP2 B0, CA0,
CB0, DB0,
DC0
2 × 10GBase-R XFP/LC/10GEBase-W XFP/LC
optical ports
LSB1XP4 B0, CA0 4 × 10GBase-R XFP/LC/10GEBase-W XFP/LC
optical ports (1:2 convergence)