3Dlabs Wildcat II 5110 User manual

=
==
=
Paä~ÄëI=fåÅK=
táäÇÅ~í=ff=RNNM=dê~éÜáÅë=^ÅÅÉäÉê~íçê=
`~êÇ=
rëÉêÛë=dìáÇÉ=
3Dlabs®, Inc.
480 Potrero Avenue
Sunnyvale, CA 94086
408 - 530 - 4 00
www.3dlabs.com

3Dlabs Graphics Accelerator Card User's Guide
ii
Copyright 2000 by 3Dlabs, Inc.
3Dlabs is a registered trademark, and Wildcat, SuperScene and DirectBurst are trademarks of 3Dlabs, Inc.
or 3Dlabs Inc. Ltd. Pentium is a registered trademark of Intel. OpenGL is a registered trademark of
Silicon Grap ics, Inc. Soft Engine is a trademark of Vibrant Grap ics, Inc. AutoCAD is a registered
trademark of AutoDesk Inc. Colorific is a registered trademark of E-Color, Inc. Microsoft, Windows NT,
Windows 2000 are registered trademarks of t e Microsoft Corporation. At lon and 3DNow! are
registered trademarks of AMD. All ot er trademarks and registered trademarks are t e property of t eir
respective olders.
Caution: C anges or modifications to your 3Dlabs Grap ics Accelerator Card not expressly approved by
3Dlabs, Inc. voids t e user’s warranty.
FCC Notice: T is equipment as been tested and found to comply wit t e limits for a Class B digital
device, pursuant to Part 15 of t e FCC Rules. T ese limits are designed to provide reasonable protection
against armful interference in a residential installation. T is equipment generates, uses, and can radiate
radio frequency energy. If product is not installed and used in accordance wit t e instruction Guide, it
may cause armful interference to radio communications; owever, t ere is no guarantee t at interference
will not occur in a particular installation. If t is equipment does cause armful interference to radio or
television reception, w ic can be determined by turning t e equipment off and on, t e user is encouraged
to try to correct t e interference by one or more of t e following measures:
1. Re-orient or relocate t e receiving antenna.
2. Increase t e separation between t e equipment and receiver.
3. Connect t e equipment to an outlet on a circuit different from t at to w ic t e receiver is
connected.
4. Consult 3Dlabs or an experienced radio/TV tec nician for assistance.
Compliance wit FCC Rules requires t at a s ielded cable be used to connect to ot er equipment. T is
device complies wit Part 15 of t e FCC Rules. Operation is subject to t e following two conditions: 1)
t is device may not cause armful interference, and 2) t is device must accept any interference received,
including interference t at may cause undesired operation.
T is Class B digital apparatus meets all t e requirements of t e Canadian Interference- Causing
Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le material brouilleur du Canada.
3Dlabs, Inc. makes no representation t at t e use of its products in t e manner described in t is
publication will not infringe on existing or future patent rig ts, nor do descriptions contained in t is
publication imply t e granting of licenses to make, use, or sell equipment or software in accordance wit
t e description.
Specifications Subject to Change Without Notice
P/N DH002000

3Dlabs Graphics Accelerator Card User's Guide iii
`
``
`lkqbkqp
lkqbkqplkqbkqp
lkqbkqp=
==
=
C apter 1– Introduction ......................................................................................................1
Welcome to 3Dlabs! ........................................................................................................2
System Requirements ......................................................................................................2
Features............................................................................................................................3
C apter 2 – Setup ................................................................................................................7
Preparing for Installation .................................................................................................8
Before you begin your installation ...........................................................................8
Installing your Wildcat II 5110 Grap ics Accelerator Card.....................................8
If you are upgrading t e grap ics card in your system...........................................10
Connecting t e Monitor.................................................................................................11
Connecting a VGA monitor....................................................................................11
Connecting two VGA monitors..............................................................................11
Connecting a Digital Flat-panel monitor................................................................12
Attac ing a Stereo Device .............................................................................................12
Installing t e Driver Software .......................................................................................12
Make sure your computer is ready .........................................................................12
Removing an existing driver under Windows NT..................................................13
Installing your Wildcat II 5110 Windows NT driver .............................................13
Removing an existing driver under Windows 2000 ...............................................13
Installing your Wildcat II 5110 Windows 2000 driver...........................................14
Heidi Drivers for AutoDesk Applications .....................................................................14
Verify t e Default Video Display Driver ......................................................................14
Verifying t e default video display driver in Windows NT...................................14
Verifying t e default video display driver in Windows 2000 ................................15
Verify t e System Startup Version ................................................................................15
Verifying t e system startup version in Windows NT ...........................................15
Verifying t e system startup version in Windows 2000.........................................15
C ecking t e Video Image ............................................................................................15
Registering Your 3Dlabs Grap ics Accelerator Card....................................................16

3Dlabs Graphics Accelerator Card User's Guide
iv
C apter 3 – Software Configuration .................................................................................17
T e 3Dlabs Wildcat II 5110 Grap ics Accelerator Card Driver ...................................18
Configuring t e Video Display......................................................................................18
Using t e Wildcat Configuration tab......................................................................18
Using t e Wildcat Monitor tab...............................................................................20
Enabling stereo display ..........................................................................................22
Enabling Multiview and Genlock..................................................................................22
Enabling Multiview features ..................................................................................22
Confirming multiview cables are detected .............................................................23
Enabling genlock features ......................................................................................23
Configuring Dual Monitors under Windows 2000........................................................23
Enabling t e Dual Monitor Feature under Windows 2000.....................................23
Adjusting colors or resolutions of eit er monitor...................................................25
Optimizing t e Wildcat II 5110 driver ..........................................................................25
Enabling application-specific optimizations ..........................................................25
Creating a custom optimization..............................................................................26
C apter 4 – Troubles ooting.............................................................................................28
Troubles ooting.............................................................................................................29
Monitors and Display Resolutions.................................................................................29
Diagnostics ....................................................................................................................29
Obtaining a Usable Video Resolution ...........................................................................30
Using t e Last Known Good option in Windows NT ............................................30
Booting into Safe Mode in Windows 2000 ............................................................30
Determining a defective unit ..................................................................................30
Reinstalling t e Video Driver........................................................................................31
Removing t e existing Wildcat II 5110 driver under Windows NT ......................31
Reinstalling t e video driver under Windows NT..................................................31
Removing an existing driver under Windows 2000 ...............................................32
Reinstalling t e video driver under Windows 2000...............................................32
Online Information ........................................................................................................32
Appendix A – Specifications.............................................................................................33
A Specifications.............................................................................................................34

3Dlabs Graphics Accelerator Card User's Guide v
Appendix B – Software License........................................................................................37
SOFTWARE LICENSE AGREEMENT.......................................................................38
Software License and Restrictions.............................................................................38
Limited Warranty...........................................................................................................39
Limited Liability ........................................................................................................39
Restricted Rig ts Notice ............................................................................................39
Termination................................................................................................................39
General.......................................................................................................................40
Appendix C – Regulatory Statements ...............................................................................41
Declaration of Conformity.............................................................................................42
Appendix D – Terms and Definitions ...............................................................................43
Terms and Definitions ...................................................................................................44
Index..................................................................................................................................49

3Dlabs Graphics Accelerator Card User's Guide
`
``
`e^mqbo=
e^mqbo=e^mqbo=
e^mqbo=N
NN
NÓ
ÓÓ
Ó=f
=f=f
=fkqolar`qflk
kqolar`qflkkqolar`qflk
kqolar`qflk=
==
=

Introduction
3Dlabs Graphics Accelerator Card User's Guide
2
tÉäÅçãÉ=íç=Paä~Äë>
tÉäÅçãÉ=íç=Paä~Äë>tÉäÅçãÉ=íç=Paä~Äë>
tÉäÅçãÉ=íç=Paä~Äë>=
==
=
T ank you for selecting a 3Dlabs® Wildcat® II 5110 Grap ics Accelerator Card!
T is User Guide is designed to provide information about t e Wildcat II 5110 Grap ics Accelerator Card.
In addition to t is guide you are strongly encouraged to use t e on line elp included in t e 3Dlabs driver
software Help screens.
póëíÉã=oÉèìáêÉãÉåíë=
póëíÉã=oÉèìáêÉãÉåíë=póëíÉã=oÉèìáêÉãÉåíë=
póëíÉã=oÉèìáêÉãÉåíë==
==
=
You must ave Microsoft Windows NT 4.0 wit Service Pack 5 (or later) or Windows 2000 installed. To
take advantage of t e dual-screen option, you must ave Windows 2000 installed.
 Pentium II®or greater processor
 Microsoft® Windows® NT 4.0 with Service Pac 5 (or later) or Windows 2000
 AGP Pro 50 expansion slot
 One open PCI slot adjacent to the AGP Pro 50 slot
 Minimum of 32 MB DRAM (64 MB recommended)
 Industry-standard, multiple-frequency monitor (VGA) or a Digital Video Interface (DVI)-compliant digital
display device
 3 MB of free space on the computer’s primary system dis for the video display driver software
Note: If you purchased the Wildcat II 5110 Graphics Accelerator Card as part of a system, it was
preconfigured to operate in your system prior to shipment. No other modifications are necessary. Also,
your system’s video drivers were installed prior to shipment and are operative when you receive the
system. No further installation or configuration is necessary unless you purchased a customer it or need
to reinstall your video card. Store the driver delivery media that came with your system in a safe place in
case you ever need to reinstall the drivers.
For more detailed information on t e operating system, refer to t e printed and online documentation
delivered wit t e system.

Introduction
3Dlabs Graphics Accelerator Card User's Guide 3
cÉ~íìêÉë
cÉ~íìêÉëcÉ~íìêÉë
cÉ~íìêÉë=
==
=
Card Interface AGP Pro 50 card designed for systems that have a 50-
watt AGP Pro slot.
Video Memory Frame Buffer: 64 MB
Texture Buffer: 64 MB
DirectBurst: 16 MB
Grap ics Controller High-speed Wildcat chipset technology with dual
display support.
RAMDAC 300 MHz
Plug-and-Play Monitor
Support
Yes
Accelerated 3D API OpenGL
Maximum Resolution; Aspect
Ratio; Refres Rate
2048 x 1152; 16:9; 75 Hz
Appendix A, Specifications
Power Management Support Display Power Management Signaling (DPMS)
Advanced Configuration and Power Interface (ACPI)
Geometry Acceleration  Model view matrix transformation of vertex and
normal coordinates
 Perspective and viewport transformations
 Texture matrix transformation of texture
coordinates
 Local display list storage and processing
 Full lighting calculations (up to 24 lights)
 View volume clipping
 Up to six user clip planes
 Image processing

Introduction
3Dlabs Graphics Accelerator Card User's Guide
4
cÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíKcÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíK=
==
=
Traditional 2D Operations  16- and 32-bit color depths (565, 8888)
 Solid and patterned area fills
 Vectors (diamond rule compliant)
 Bloc moves (screen-to-screen)
 Bloc gets (screen-to-system)
 Bloc puts (system-to-screen)
 Bilinear scaling
OpenGL (1.2 Compliant)
Operations
 Image support for multiple formats, zooming,
bilinear scaling, color matrix, and color tables
 Harware accumulation operations
 Fogging: linear, exponential, exponential2, and
user-defined
 Antialiased points, vectors, and polygons
 Points (2D, 3D wide)
 Vectors (2D and 3D lines, line strips; wide,
stippled)
 Polygons (triangles, triangle strips, quads, quad
strips, polygons, point/line polygon mode)
 Texture mapping: point, bilinear, trilinear, and
multiple internal formats
 24- and 32-bit depth buffering
 Alpha operations
 Scissoring
 Dithering
 Fast window clears
 Window clipping
 Fast window-mode double buffering
 Mas ing
 Frame-sequential and interlaced stereo support
 Matrix transformations
 Stencil operations
 Rich set of blending operations

Introduction
3Dlabs Graphics Accelerator Card User's Guide 5
cÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíKcÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíK=
==
=
OpenGL (1.2 Compliant)
Extension Support
 Imaging Extensions:
 Pixel buffer
 Color table
 Color matrix
 Convolution
 Blend Extensions:
 Color
 Minmax
 Function separate
 Subtract
 Fog Extensions:
 Fog function
 Fog offset
 Occulsion culling
 Texture Extensions:
 3D textures: edge, border, and LOD clamps
 Mipmap generation
 Video Extensions:
 Interlace
 Interlace read
 422 pixels
 Swap Control Extensions:
 Swap control
 Swap frame loc
 Swap usage
 Texture color table
 Pixel texture and 3D texturing
 Pbuffer
 Image buffer
 Gamma
 Stencil operation wrap
 Separate specular
 Post-texturing specular

Introduction
3Dlabs Graphics Accelerator Card User's Guide
6
cÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíKcÉ~íìêÉëI=ÅçåíK
cÉ~íìêÉëI=ÅçåíK=
==
=
Additional Features  SuperScene full-scene multisampled anti-
aliasing:
 Point sampled with sixteen samples
 Sample location jittering
 Dynamic sample allocation
 Dynamic sample bac off
 Two video loo -up tables
 Eight stencil planes
 Eight double-buffered overlay planes
 32-bit Z buffer
 High-performance DACs that directly drive
display devices
 DDC2B Display Data Channel standard
 Head-mounted displays and shutter glasses
(frame sequential and interlaced stereo required)
 Onboard texture memory with full mipmapped
trilinear interpolated texture processing
 Digital Video Interface (DVI)-I display support
 Big and Little Endian support
 Global and local texture modes
 Textures per screen
=
==
=

3Dlabs Graphics Accelerator Card User's Guide
`
``
`e^mqbo=
e^mqbo=e^mqbo=
e^mqbo=O=
O=O=
O=Ó
ÓÓ
Ó=p
=p=p
=pbqrm
bqrmbqrm
bqrm=
==
=

Setup
3Dlabs Graphics Accelerator Card User's Guide
8
mêÉé~êáåÖ=Ñçê=fåëí~ää~íáçå
mêÉé~êáåÖ=Ñçê=fåëí~ää~íáçåmêÉé~êáåÖ=Ñçê=fåëí~ää~íáçå
mêÉé~êáåÖ=Ñçê=fåëí~ää~íáçå=
==
=
Note: If you purchased your Wildcat II 5110 Graphics Accelerator Card as part of a system, it was
installed and configured prior to shipment. The following instructions for hardware installation are
necessary only if you purchased a customer it or need to reinstall your video card.
Before you begin your installation
1. Save any work in progress and exit any open applications. Always back up your system before
you install any new ardware or software.
2. Have a P illips- ead screwdriver ready.
3. Turn off power to t e computer.
Important: Physically remove the power cord from the system and wait 15 to 30 seconds for
standby power to dissipate. Damage can occur to add-in components if power is not physically
removed from the system during installation procedures.
4. Take every possible precaution against static electricity as you prepare to install t e card. Static
can damage components. If an anti-static wrist strap was included in your box, please use it
during ardware installation. You s ould also try to work in a static free area (suc as on a tile
floor rat er t an carpet).
 Touch the metal chassis of the computer to drain off any static electricity before touching the card.
 Do not wear wool or polyester clothing.
 Wor in an area with a relative humidity of at least 50 percent.
 Keep the card in the anti-static bag until you are ready to install it.
 Handle the card as little as possible and only by the edges.
Note: Be sure to register your new card using one of the options described on page 16.
Installing your Wildcat II 5110 Graphics Accelerator Card
1. Refer to your computer’s documentation for instructions on opening and closing t e computer,
identifying t e AGP Pro expansion slot and PCI expansion slots, and adding expansion cards.
2. C eck your system documentation to locate t e appropriate slots w ic to install your card. Your
Wildcat II 5110 Grap ics Accelerator Card includes an adjacent (attac ed) power supply card.
T e adjacent PCI slot must be empty for cooling purposes.
3. Turn off power to t e computer and to t e monitor and disconnect t e cables from t e computer
(follow t e instructions under Before you begin your installation).
Note: If you are replacing a graphics card, be sure to uninstall your old video driver software before
tuning off your system and removing your old graphics card. Refer to Installing the Driver Software later
in this chapter for details on uninstalling drivers.
4. Remove t e cover from your system so you can access t e slots into w ic you will be installing
your Wildcat II 5110 Grap ics Accelerator Card. If you ave not already removed any existing
grap ics card(s) from your system, t en do so now.

Setup
3Dlabs Graphics Accelerator Card User's Guide 9
5. If necessary, remove t e back panel covers from t e slots into w ic you are installing your
Wildcat II 5110 Grap ics Accelerator Card, using a P illips- ead screwdriver.
6. If an anti-static wrist strap was included in your box, attac it to your wrist and attac t e ot er
end to a bare metal (as opposed to painted or sticker covered) surface on your system’s c assis.
7. Remove your Wildcat II 5110 Grap ics Accelerator Card from its anti-static packaging. Write
down t e serial number for product registration and future use. T e serial number is located on a
board label and looks like t is:
136001B123456 Made in XXX Week XXXX

Setup
3Dlabs Graphics Accelerator Card User's Guide
10
8. Place t e card into t e correct slots and seat firmly. See your system documentation for
instructions on securing t e card to t e c assis. Loose cards and connections can cause grounding
and operating problems.
9. Remove t e anti-static wrist strap, if used, and replace t e cover on your system.
10. Reconnect t e power cord.
If you are upgrading the graphics card in your system
Note: These instructions may be different than how you normally upgrade your graphics card or other
devices, but have been found to be the best method of insuring a successful installation of your new
hardware and software.
1. Uninstall t e drivers for your old grap ics card. Refer to your old grap ics card’s documentation
or Help files for instructions on removing or uninstalling t e old grap ics card’s driver software.
2. Remove t e existing grap ics card from your system. To install your Wildcat II 5110 Grap ics
Accelerator Card, see t e ardware installation instructions.
3. Install t e Wildcat II 5110 Grap ics Accelerator Card driver software; see Installing the Driver
Software later in t is c apter.

Setup
3Dlabs Graphics Accelerator Card User's Guide 11
`çååÉÅíáåÖ=íÜÉ=jçåáíçê
`çååÉÅíáåÖ=íÜÉ=jçåáíçê`çååÉÅíáåÖ=íÜÉ=jçåáíçê
`çååÉÅíáåÖ=íÜÉ=jçåáíçê=
==
=
The Wildcat II 5110 supports connections for one VGA monitor, one flat panel monitor, or two VGA monitors (with
one using an adapter for the DVI-I connector). The Wildcat II 5110 has one DVI-I connector and one VGA
connector.
Connecting a VGA monitor
1. Make sure t e power to t e computer is turned off.
2. Connect t e workstation monitor’s video cable to t e 15-pin D-Sub connector on t e Wildcat II
5110 video card.
3. Turn on power to t e workstation. If t e monitor’s Power On LED does not illuminate or t e
monitor does not display t e startup sequence, consult C apter 4, Troubleshooting.
Connecting two VGA monitors
Note: If you are connecting more than one VGA monitor to the Wildcat II 5110, you must use a DVI-
Analog adapter to connect to the DVI-I connector.
The secondary monitor may be an analog flat panel monitor.
1. Make sure t e power to t e computer is turned off.
2. Follow t e instructions under Connecting a VGA monitor for connecting t e first VGA monitor.
3. Connect t e second monitor’s 15-pin VGA connector to t e VGA end (see below) of t e
DVI-Analog adapter.
4. Connect t e DVI-I end of t e adapter to t e DVI-I port on t e Wildcat II 5110 video card.
5. Turn on power to t e workstation. If t e monitor’s Power On LED does not illuminate or
t e monitor does not display t e startup sequence, consult C apter 4, Troubleshooting.
VGA connector
(analog)
DVI-I connector
(digital)

Setup
3Dlabs Graphics Accelerator Card User's Guide
12
Connecting a igital Flat-panel monitor
Note: The Wildcat II 5110 features support for one digital flat-panel monitor via a DVI-I connector (with
DVI-D functionality).
1. Make sure t e power to t e computer is turned off.
2. Connect t e workstation monitor’s video cable to t e DVI-I connector on t e Wildcat II 5110
video card.
3. Turn on power to t e workstation. If t e monitor’s Power On LED does not illuminate or t e
monitor does not display t e startup sequence, consult C apter 4, Troubleshooting.
íí~ÅÜáåÖ=~=píÉêÉç=aÉîáÅÉ
íí~ÅÜáåÖ=~=píÉêÉç=aÉîáÅÉíí~ÅÜáåÖ=~=píÉêÉç=aÉîáÅÉ
íí~ÅÜáåÖ=~=píÉêÉç=aÉîáÅÉ=
==
=
Power off your system and connect t e stereo ardware to t e round, stereo connector on t e card. See t e
documentation t at came wit your stereo ardware for information on ow to use stereoscopic display.
Plug in and start up your system, including perip erals, and log on to your operating system.
Note: To configure the display settings for stereo display, see Chapter 3, Using the Video Card for step-
by-step instructions.
fåëí~ääáåÖ=íÜÉ=aêáîÉê=pçÑíï~êÉ
fåëí~ääáåÖ=íÜÉ=aêáîÉê=pçÑíï~êÉfåëí~ääáåÖ=íÜÉ=aêáîÉê=pçÑíï~êÉ
fåëí~ääáåÖ=íÜÉ=aêáîÉê=pçÑíï~êÉ=
==
=
If you received your Wildcat II 5110 Grap ics Accelerator wit a system, t e grap ics drivers were
installed prior to s ipment. T is section only applies if you purc ased your Wildcat II 5110 as an
upgrade, are reinstalling t e driver, or are updating t e operating system to Microsoft Windows 2000.
T is section describes t e two software installation processes for supported Windows operating systems.
Make sure your computer is ready
Make sure your workstation as t e following before installing Wildcat II 5110 driver software:
 Microsoft Windows NT Wor station 4.0 operating system with Service Pac 5 (or later) or Microsoft
Windows 2000 operating system software installed
 3 MB of free space on the computer’s primary system dis
Important: You must have the correct driver for the Windows NT 4.0 or Windows 2000
operating system. If you are unsure, refer to the README.TXT file located on the driver delivery
media for this information. Refer to the Microsoft Windows NT 4.0 or Windows 2000
documentation and online Help for more information on installing drivers and software
application programs. If you are removing and reinstalling the Wildcat II 5110 driver, see
Chapter 4 Reinstalling the Video Driver.
3-Pin
Minidin
Stereo
Connector
Stereo connector

Setup
3Dlabs Graphics Accelerator Card User's Guide 13
Removing an existing driver under Windows NT
1. Start up Windows NT. Log on using an account wit administrative privileges.
2. From t e operating system Start menu, go to Settings/Control Panel and double-click
Add/Remove Programs.
3. On t e Add/Remove Programs Properties Install/Uninstall tab, ig lig t t e Display Driver
you are removing and click Add/Remove.
4. Click Yes w en prompted to confirm t e driver removal, and follow t e prompts. Reboot t e
system before installing t e new Wildcat II 5110 driver.
Installing your Wildcat II 5110 Windows NT driver
1. Start up Windows NT. Log onto an account wit administrative privileges.
2. Place t e 3Dlabs driver delivery media in t e appropriate drive.
3. From t e operating system Start menu, go to Settings/Control Panel/Display and click t e
Settings tab.
4. Click Display Type, t en click C ange.
5. In t e C ange Display dialog box, click Have Disk.
6. In t e Install From Disk dialog box, type t e pat to t e drive or directory t at contains t e
delivery media.
7. In t e C ange Display dialog box, verify t at t e Wildcat II 5110 driver is ig lig ted, t en click
OK.
8. Click Yes w en asked if you want to install a t ird-party driver. T e files are copied from t e
delivery media.
9. After t e driver files are copied, a message t at t e driver successfully installed displays. Click
OK.
10. Click Close to exit t e Display Type dialog box.
11. Click Close to exit t e Display Properties dialog box.
12. W en told t at t e workstation must be restarted for t e new settings to take effect, remove t e
driver media from t e disk drive. Click Yes to restart t e workstation.
13. After t e system restarts and you log on, a message displays stating t at a new display driver as
been installed, and t at you s ould use t e Display option in t e Control Panel to select t e
preferred display resolution. Click OK.
Removing an existing driver under Windows 2000
1. Start up Windows 2000. Log on using an account wit administrative privileges.
2. From t e operating system Start menu, go to Settings/Control Panel and double-click
Add/Remove Programs.
3. Under C ange or Remove Programs, ig lig t t e current Display Driver and click
C ange/Remove.
4. Click Yes w en prompted to confirm t e driver removal, and follow t e prompts to
complete t e driver removal.
5. Click OK w en notified t at t e driver removal is complete and reboot your system.

Setup
3Dlabs Graphics Accelerator Card User's Guide
14
Installing your Wildcat II 5110 Windows 2000 driver
1. After installing your Wildcat II 5110 Grap ics Accelerator Card, start up Windows 2000 and log
on using an account wit administrative privileges. T e Hardware Wizard appears.
2. Click Next on t e Found New Hardware Wizard.
3. Under Install Hardware Device Drivers, click “Searc for a suitable driver for my device
(recommended),” t en click Next.
4. Under Locate Driver Files, make sure t e appropriate searc location is selected, and t at Disk 1
of t e driver media is in t e appropriate drive; t en, click Next. T e Wizard locates t e driver
installation files.
5. Under Driver Files Searc Results, click Next to start t e installation.
6. Insert Disk 2 w en prompted, t en click OK to continue wit t e installation.
7. Once t e driver successfully installs, click Finis to dismiss t e Found New Hardware Wizard.
Important: Windows 2000 recognizes the dual pipelines as two devices. The Found New
Hardware Wizard will display a second time to finish the installation.
You must repeat Steps 3 – above to complete the installation.
8. W en told t at t e workstation must be restarted for t e new settings to take effect, remove
t e delivery media from t e disk drive (if applicable) and click Yes to restart t e
workstation.
eÉáÇá=aêáîÉêë=Ñçê= ìíçaÉëâ= ééäáÅ~íáçåë
eÉáÇá=aêáîÉêë=Ñçê= ìíçaÉëâ= ééäáÅ~íáçåëeÉáÇá=aêáîÉêë=Ñçê= ìíçaÉëâ= ééäáÅ~íáçåë
eÉáÇá=aêáîÉêë=Ñçê= ìíçaÉëâ= ééäáÅ~íáçåë=
==
=
T e Wildcat II 5110 Heidi® device driver allows full screen multisampling of and compatibility wit
AutoDesk applications as well as ardware acceleration of t e Wildcat II 5110 t roug t e use of
OpenGL. To install t e Heidi driver and to activate full screen multisampling, consult t e README.TXT
located on disk 3 of t e Wildcat II 5110 delivery media.
sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêáîÉê=
sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêáîÉê=sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêáîÉê=
sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêáîÉê==
==
=
T is section describes ow to verify t e correct display driver is loaded on your workstation.
Verifying the default video display driver in Windows NT
1. From t e operating system Start menu, go to Settings/Control Panel/Display, and click t e
Settings tab on t e Display Properties dialog box.
2. Click Display Type, t en verify t at Wildcat II 5110 is listed under Display. T is indicates
t at t e appropriate driver is installed.
3. Click Cancel to close t e Display Properties dialog box.