3M Accuglide V HSP Datasheet
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page i
44-0009-2157-5 / ECO#0086964
Instructions and Parts List
Important Safety Information
BEFORE INSTALLING OR OPERATING THIS EQUIPMENT
Read, understand and follow all safety and operating instructions.
Spare Parts
It is recommended you immediately order the spare parts listed in the “Spare
Parts/Service Information” section. These parts are expected to wear through
normal use, and should be kept on hand to minimize production delays.
3M-Matic™Accuglide™V HSP
Type 12000
Taping Heads
2 Inch
Serial #:
For reference, record machine serial number here.
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page ii
44-0009-2157-5 / ECO#0086964
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page iii
44-0009-2157-5 / ECO#0086964
Replacement Parts and Service Information
To Our Customers:
This is the 3M-Matic™/AccuGlide™/Scotch®equipment you ordered.
It has been set up and tested in the factory with Scotch®Tapes.
Included with each machine is an Instructions and Parts List manual.
Technical Assistance / Replacement Parts and Additional Manuals:
For technical assistance, contact our help line at 1-800-328-1390.
Provide the customer support coordinator with the model/machine name,
machine type, and serial number that are located on the identication plate
(For example: Model - Accuglide V HSP 2 Inch - Type 12000
To order replacement parts, contact us:
CSPD division of Combi Packaging Systems LLC. Phone: 1-800-344-9883
5365 East Center Dr. N.E. Fax: 1-877-847-5883
www.combi.com
3M-Matic
TM
3M Company
St Paul, MN 55144 USA
Model Part Number
Electrical Drawing
Type Serial Number
Indoor Industrial use only 4000563
I
N
T
E
R
T
E
K
SCCR Volt Hertz Air Supply IP
Ampere Phase Watt Air Consumption
Identication Plate
Year
Minimum billing on parts orders will be $50.00.
Replacement part prices available on request.
There will be a 15% restocking fee per invoice on returned parts.
Note: For replacement part information and ordering outside the U.S.
contact the local 3M representative or subsidiary.
CSPD division of Combi Packaging Systems LLC.
6299 Dressler Rd NW I North Canton, OH 44720
1-800-344-9883 Fax 877-847-5883
https://store.combi.com/CSPD/PublicStore/
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page iv
44-0009-2157-5 / ECO#0086964
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page v
44-0009-2157-5 / ECO#0086964
Replacement Parts and Service Information (continued)
To Our Customers:
This is the 3M-Matic™/AccuGlide™/Scotch®equipment you ordered.
It has been set up and tested in the factory with Scotch®tapes.
Included with each machine is an Instructions and Parts List Manual.
Order parts by part number, part description, and quantity required.
Also, when ordering parts or additional manuals, include model/machine name,
Service, replacement parts, and additional manuals available direct from:
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page vi
44-0009-2157-5 / ECO#0086964
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page vii
44-0009-2157-5 / ECO#0086964
Table of Contents - Accuglide™V HSP - 2 inch - Type 12000
Manual 2:
Accuglide™V HSP Taping Head Manual - 2 Inch - Type 12000 Page
Cover Page
Replacement Parts and Service Information .....................iii– v
Table of Contents .............................................. vii
Equipment Warranty and Limited Remedy........................ viii
Intended Use ................................................... 1
Taping Head Contents / How to Use Manual .......................3
Important Safeguards..........................................4-5
................................................ 6-7
Dimensional Drawing ....................................... 7
Installation .....................................................8
Receiving and Handling .....................................8
Installation Guidelines ......................................8
Tape Leg Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tape Width Adjustment .....................................8
Operation ................................................... 9-11
Tape Loading – Taping Head..............................10-11
Maintenance ............................................... 12-13
Blade Replacement ........................................ 12
Blade Guard .............................................. 12
Blade Oiler Pad ........................................... 12
Cleaning ................................................. 13
........................ 13
Adjustments................................................ 14-15
Tape Latch Alignment ...................................... 14
Tape Drum Friction Brake ................................... 14
Applying Mechanism Spring ................................ 15
One-Way Tension Roller .................................... 15
Troubleshooting Guide .......................................17-18
Spare Parts/Service Information ................................. 19
Recommended Spare Parts ................................. 19
Replacement Parts and Service............................. .-21
Replacement Parts Illustrations and Parts List ........ 23-End of Manual
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page viii
44-0009-2157-5 / ECO#0086964
Warranty
Warranty
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,
THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND
ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING,
A CUSTOM OR USAGE OF TRADE:
3M sells its 3M-Matic™Accuglide V HSP Taping Head, Type 12000
with the following warranties:
1. The Taping Head blade, springs and rollers will be free from defects in material and
manufacture for ninety (90) days after delivery.
2. All other Taping Head parts will be free from defects in material and manufacture for
three (3) years after delivery.
If any part is defective within this warranty period, your exclusive remedy and 3M’s and
seller’s sole obligation shall be, at 3M’s option, to repair or replace the part. 3M must
receive actual notice of any alleged defect within a reasonable time after it is discovered,
but in no event shall 3M have any obligation under this warranty unless it receives such
All notices required hereunder shall be given to 3M solely through the 3M-Matic™
Help line. To be entitled to repair or replacement as provided under this warranty,
the part must be returned as directed by 3M to its factory or other authorized service
station designated by 3M. If 3M is unable to repair or replace the part within a
reasonable time after receipt thereof, 3M, at its option, will replace the equipment or
refund the purchase price. 3M shall have no obligation to provide or pay for the labor
required to remove any part or equipment or to install the repaired or replacement part or
equipment. 3M shall have no obligation to repair or replace those parts failing due to
normal wear, inadequate or improper maintenance, inadequate cleaning, non-lubrication,
improper operating environment, improper utilities, operator error or misuse, alteration or
Limitation of Liability: Except where prohibited by law, 3M and seller will not be liable
for any loss or damage arising from this 3M equipment, whether direct, indirect, special,
incidental, or consequential, regardless of the legal theory asserted, including breach of
warranty, breach of contract, negligence, or strict liability.
Note: The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability
may be changed only by a written agreement signed by authorized representatives
of 3M and seller.
AccuGlide™, Scotch™, and 3M-Matic™are Trademarks of 3M, St. Paul, Minnesota 55144-1000
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 1
44-0009-2157-5 / ECO#0086964
AccuGlide™ V HSP Taping Head - 2 inch, Type 12000
Intended Use
The intended use of the V HSP 2 Inch - Type 12000 Upper and LowerTaping Heads is to apply a
“C” clip of Scotch®
of regular slotted containers. The compact size and simplicity of the taping head makes it
suitable for mounting in box conveying systems other than 3M-Matic™ case sealers.
This includes replacement of other types of taping, gluing or stapling heads in existing
case sealing machines.
The V HSP 2 Inch - Type 12000 Upper and Lower Taping Heads have been designed and tested for
use with Scotch®
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 2
44-0009-2157-5 / ECO#0086964
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 3
44-0009-2157-5 / ECO#0086964
AccuGlide™V
H
SP - 2 inch - Type 12000 Upper and Lower Taping Heads consist of:
Qty. Part Name
1 Taping Head Assembly
1 Tape Drum and Bracket Assembly
1 Hardware and Spare Parts Kit
General Information
This instruction manual covers safety aspects, handling and transport, storage, unpacking,
preparation, installation, operation, set-up and adjustments, technical and manufacturing
list of the 3M-Matic™Accugllide V HSP (2 Inch - Type 12000) 3M Industrial Adhesives and
Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) Edition
September 2020/Copyright 3M 2020. All rights reserved The manufacturer reserves the
right to change the product at any time without notice. Publication
© 3M 2020. 44-0009-2157-5
How to use this Manual
The manual is an important part of the machine; all information contained herein is
intended to enable the equipment to be maintained in perfect condition and operated
safely. Ensure that the manual is available to all operators of this equipment and the
manual is kept up to date with all subsequent amendments. Should the equipment be
sold or disposed of, please ensure that the manual is passed on with the machine.
Electrical and pneumatic diagrams are included in the manual. Equipment using PLC
controls and/or electronic components will include relevant schematics or programs in
the enclosure (or will be delivered separately as needed)
Keep the manual in a clean and dry place near the machine. Do not remove, tear or
rewrite parts of the manual for any reason. Use the manual without damaging it.
However, if the manual has been lost or damaged, ask your after sale service for a
new copy (if it is possible, please have the manual name, part number, and revision
information and/or model/machine name, machine type, and serial number) that
(For example: V HSP 2” - Type 12000).
Note: All the important Warning notes related to the operation of the machine are
Updating the Manual
The user may receive pages or parts of the manual which contain amendment
Taping Head Contents
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 4
44-0009-2157-5 / ECO#0086964
(Important Safeguards continued on next page)
Explanation of Signal Word and Possible Consequences
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury and/or
property damage.
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury and/or
property damage.
This safety alert symbol identies important messages in this
manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR
OPERATING THIS EQUIPMENT.
Caution
Warning
• To reduce the risk associated with
mechanical hazards
- Read, understand and follow all safety
and operating instructions before
operating or servicing the case sealer
and or service this equipment
Caution
• To reduce the risk associated with
muscle strain:
- Use proper body mechanics when
removing or installing taping heads
that are moderately heavy or may be
considered awkward to lift
• To reduce the risk associated with
impact hazards
- Place the taping head on a smooth
level surface when maintaining or
servicing this equipment
Warning
• To reduce the risk associated with
sharp blade hazards:
guards. The blades are extremely sharp.
Warning
• To reduce the risk associated with
shear, pinch, and entanglement hazards
- T
on associated equipment before
performing any adjustments, mainte-
nance, or servicing the taping heads
- Never attempt to work on the taping
head or load tape while the box drive
system is running
Warning
Important Safeguards
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 5
44-0009-2157-5 / ECO#0086964
Figure 1-1 Replacement Labels/3M Part Numbers
Important Safeguards (continued)
78-8070-1335-0
78-0025-1903-7
Important - In the event the following safety labels are damaged or destroyed, they must be replaced to ensure
operator safety. See "Replacement Parts Illustrations and Parts Lists" for label part numbers.
78-8137-0223-6
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 6
44-0009-2157-5 / ECO#0086964
continued on next page)
Specications
1. Tape:
For use with Scotch®
2. Tape Width:
36mm or 1-1/2 inches minimum to 48mm [2 inches] maximum.
3. Tape Roll Diameter:
Up to 405mm [16 inches] maximum on a 76.2mm [3 inch] diameter core.
(Accommodates all system roll lengths of Scotch®
4. Tape Application Leg Length - Standard:
50.8mm ± 6mm [2 inches ± 1/4 inch]
5. Box Size Capacities:
For use with center seam regular slotted containers.
Length *– 150mm [6 inches]
Height * – 101mm [4 inches]
Width *– 150mm [6 inches]
* Note: Box size capacities may also be determined by the case conveying system used.
6. Operating Conditions:
Use in dry, relatively clean environments at 5° to 40°C [40° to 105°F] with clean dry boxes.
Important – Taping heads should not be washed down or subjected to conditions causing
moisture condensation on components.
7. Taping Head Dimensions:
Length – 400mm [15.75 inches]
Height – 586.5mm [23.1 inches] (with tape)
Width – 79.5mm [3.13 inches] (without mounting spacers)
Weight – Packaged: 5.9kg [13 lbs.] Unpackaged: 4.8kg [10.5 lbs.]
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 7
44-0009-2157-5 / ECO#0086964
Specications (continued)
406.4 mm
[16.00 in.]
Maximum
Roll Diameter
350.0 mm [13.78 in]
400.0 mm [15.75 in]
79.5 mm [3.13 in]
203.7mm[8.02in]
152.0mm[5.98in]
18.0 mm [.71 in]
37.5 mm [1.48 in]
101.6mm[4.00in]
MinimumStandard
HeadSpacing
72.4 mm [2.85 in]
586.5mm[23.09in]
383.3mm[15.09in]
142.9 mm [5.63 in]
Box Direction
3.2 mm [.13 in]
Max
3.2 mm [.13 in]
Max
M6 Mounting Holes
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 8
44-0009-2157-5 / ECO#0086964
Receiving And Handling
After the taping head assembly has
been unpackaged, examine the unit
for damage that might have occurred
during transit. If damage is evident,
the transportation company and also
notify your 3M Representative.
Installation Guidelines
The taping head assembly can be
used in converting existing or in
custom made machinery.
It can be mounted for top taping
or bottom taping. Refer to “Box Size
Capacities,” as well as Figure 2-1
following points making installations:
Important – Always conduct a hazard
review to determine appropriate
guarding requirements when the
installation is in an application
other than 3M-Matic™equipment
1. The box conveying system must
positively propel the box in a
past the taping head assembly since
the box motion actuates the taping
mechanism.
2. If a pusher/cleated conveyor is used,
steps should be taken in conveyor to
prevent pusher from contacting apply-
damage to taping head).
3. Figure 2-1 illustrates the typical
mounting relationship for opposing
taping head assemblies to allow taping
The taping heads must be completely
staggered so only one tape seal is
being applied at one time.
4. Mounting studs are provided with the
taping head, but special installations
may require alternate mounting means.
5. Box hold-down/guide skis should be
provided and taping head mounted so
that side plates are 6mm [1/4 inch]
maximum away from the ski surface
on which the box rides.
Tape Leg Length
Taping heads are factory set to apply
58mm [2 1/4 inches] tape legs.
Tape Width Adjustment
Taping heads are factory set to apply
48mm [2 inch] wide tape. If it is
necessary to align the tape or to apply
narrower tapes, refer to “Adjustments –
Tape Web Alignment” set-up procedure.
Caution
• To reduce the risk associated with
muscle strain:
- Use proper body mechanics when
removing or installing taping heads
that are moderately heavy or may be
considered awkward to lift
• To reduce the risk associated with
sharp blade hazards:
guards. The blades are extremely sharp.
Warning
Installation
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 9
44-0009-2157-5 / ECO#0086964
Operation
Tape Supply Roll
Tape Drum
Tape Adhesive Side
Wrap Roller
Wrap Roller
Mounting Block
Mounting Block
Tape Support Assembly
Tape Cut O Blade
Blade Guard
Apply Mechanism Spring
Cut O Spring One-Way
Tension Roller
Bung Arm
Link Arm
Figure 3-1 Taping Head
Components/
Threading Diagram -
Upper Head
(Left Side View)
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 10
44-0009-2157-5 / ECO#0086964
Figure 3-3
Tape Loading /
Threading
Figure 3-3
Insert threading needle through rollers in
direction indicated by arrows.
Operation (continued)
It is recommended that the detailed
instructions and sketches in this manual
taping head is loaded/threaded until the
operator becomes thoroughly familiar
with the tape loading operation.
Note – Remove tape roll before removing
taping head from machine to
minimize weight.
Tape Loading – Taping Head
1. Place the Taping Head in a
convenient working position.
2. Use Figures 3-3/3-5 and tape thread-
ing label. Position tape roll so adhesive
side of tape faces front of taping head
as it’s pulled from supply roll.
3. Guide the tape around the tension wrap
roller (Position 1) then back around the
one-way tension roller (Position 2).
4. Continue pulling the tape down and
past the wrap roller (Position 3) and
through the Tape Support Assembly.
5. Pull the tape down past the applying
roller (Position 4). When properly
threaded the adhesive side of the
tape should be facing the tension
roller at position 2 and away from
the guide roller at position 3.
6. Cut away any excess tape.
Important – Do not cut against apply
roller - roller damage could occur.
Tape Loading – Lower Taping Head
1. Remove the lower taping head from
the conveyor bed or associated
equipment and place it a convenient
working position.
2. Lower taping head is loaded and
threaded in same manner as upper head.
• To reduce the risk associated with
sharp blade hazards:
guards. The blades are extremely sharp.
Warning
Caution
• To reduce the risk associated with
muscle strain:
- Use proper body mechanics when
removing or installing taping heads
that are moderately heavy or may be
considered awkward to lift
• To reduce the risk associated with
impact hazards
- Place the taping head on a smooth
level surface when maintaining or
servicing this equipment
• To reduce the risk associated with shear,
pinch, and entanglement hazards
- T
on associated equipment before
performing any adjustments, mainte-
nance, or servicing the taping heads
- Never attempt to work on the taping
head or load tape while the box drive
system is running
Warning
4.Tape Support Finger
One-Way
Tension Roller
1
2
3
4
Wrap Roller
Tension
Wrap
Roller
Tape
Support
Assembly
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 11
44-0009-2157-5 / ECO#0086964
Figure 3-4 Tape Loading/Threading
Figure 3-5 Tape Loading/Threading
Operation (continued)
Figure 3-4
Place tape roll on tape drum to
dispense tape with adhesive side
forward. Seat tape roll fully against
lead end to threading needle as
shown.
Manually turn tape roll to create
slack tape while pulling threading
needle through tape applying
mechanism until needle is through
and tape is in alignment with
applying roller.
Excess tape can be cut with a
scissors at applying roller.
• To reduce the risk associated with
sharp blade hazards:
guards. The blades are extremely sharp.
Warning
North American - ENG
Date Released:
10-20-20
3M-Matic™Accuglide V HSP - 2 Inch Taping Head - Type 12000
Page 12
44-0009-2157-5 / ECO#0086964
(Maintenance continued on next page.)
Maintenance
The AccuGlide™ V HSP 2 Inch
Taping Head has been designed for
long, trouble free service. The taping
head will perform best when it
receives routine maintenance and
cleaning. Taping head components
that fail or wear excessively should
be promptly repaired or replaced to
prevent damage to other portions of
the head or to the product.
Blade Replacement, Upper and Lower
Taping Heads – Figure 4-1
1. Loosen, but do not remove, the
blade screws (A). Remove and
discard old blade.
2. Mount the new blade (B) with the
beveled side away from the blade
holder.
3. Bottom the blade slots against
the screws (this will position the
blade at the correct angle.)
Tighten the blade screws to
secure the blade.
Note – Check the blade position
to insure proper clearance
between blade and guard by
slowly pivoting blade guard back.
Blade Guard
The blade guard covers the blade
whenever a box is not being taped.
Periodically check to be sure the
blade guard is functioning properly
and returning to cover the blade.
Replace any defective parts.
Blade Oiler Pad
To reduce adhesive build-up, the
taping heads are equipped with
a factory pre-lubricated felt oiler
the cutting edge of the blade.
Blade maintainance should include
keeping the felt oiler pad saturated
with Silicone.
Should tape adhesive build-up
occur on blade, carefully wipe
clean with an oily cloth.
• To reduce the risk associated with
sharp blade hazards:
guards. The blades are extremely sharp.
Warning
• To reduce the risk associated with
shear, pinch, and entanglement hazards
- T
on associated equipment before
performing any adjustments, mainte-
nance, or servicing the taping heads
- Never attempt to work on the taping
head or load tape while the box drive
system is running
Warning
Figure 4-1 Blade Replacement
Blade
(B)
Blade
Screws
(A)
Blade
Holder
This manual suits for next models
1
Table of contents
Other 3M Tape Deck manuals
