3TEMP Hipster 1grp User manual

Rev.100318-01-v1
Made in Sweden
Hipster 1grp
Hipster 1grp 300302
User manual

Rev.100318-01-v1
2
Hipster 1grp

Rev.100318-01-v1
3
Hipster 1grp
1. Preface
Arvika, Sweden; the home of where the Hipster brewer was created and innovated.
It is in this small industrial town in the middle of Sweden, where hard working men and
women reap their harvest of diligent work; a work of tradition and dedicated skilled
craftsmanship. Arvika is sincerely famous for it’s warmth during the summer, for it’s
environment of magnicent forests and foremost for the surroundings of 365 smaller
lakes, that enhance mysticism and stories from the past to the present.
The home of the Hipster brewer.
The Hipster is classied by baristas and coee people all over the world as one of
the best amongst lter coee machines. Hipster is a unique brewer. Unlike any other
brewer in the market it let’s you control blooming, temperatures in 3 phases and water
distribution for each recipe. It is designed and developed in Sweden by a team with vast
experience from the coee industry.
The Hipster is a game changer as it brings lter coee to a new level. Precision of ow
rate, temperature and extraction time are critical factors to reach the best possible
extraction. In order to preserve the coee’s origin in avour and fragrance, makes the
demands high on these 3 parameters precision in order to recreate the same taste
experience time and again.
The fresh water system and the recipe parameters makes a huge impact on the taste
and a tiny impact on the environment as it consumes barely 7 watts when not brewing.
We hope that you will enjoy your new Hipster brewer.
With best wishes
Copyright 2019 All rights reserved
3TEMP/PLAE2TECH
The Story

Rev.100318-01-v1
4
Hipster 1grp

Rev.100318-01-v1
5
Hipster 1grp
Table of contents
1. Preface ...........................................................................3
2. Safety information ................................................. 6
2.1 Introduction..........................................................................................6
2.2 This user manual...............................................................................6
2.3 Intended use .......................................................................................6
2.4 Capacity of the machine...............................................................7
2.5 General safety instructions .........................................................7
2.6 Disposal..................................................................................................9
3. Before rst use ..........................................................9
4. Product description Hipster Brewer........... 10
4,1 Description......................................................................................... 10
4.2 The cycle of The Hipster taste-proling ............................ 11
5. Technical data..........................................................12
5.1 HIPSTER1GRP....................................................................................12
5.2 Wiring diagram TB Tube .............................................................13
6. Unpacking................................................................. 14
7. Installation instructions ......................................15
7.1 Description..........................................................................................15
7.2 Adjust the feet .................................................................................16
7.3 Adjust the brewer hat in level. .................................................16
7.4 Connect the water lter system..............................................17
7.5. Connect the network-cable.....................................................17
(RJ45) white cable. To the LAN-port of the router. ......17
7.6 Machine status .................................................................................18
8. User instructions................................................... 19
8.1 Prepare a brew .................................................................................19
8.2 Select recipe ................................................................................... 20
8.3 Thermos detachable serving base...................................... 22
9. Recipe settings ...................................................... 23
9.1 Set a recipe for batch or single brew. ................................. 23
10. Recipe settings with button controller... 24
11. Care and maintenance after use. ............... 27
11.1 Cleaning instructions ................................................................. 27
11.2 Cleaning Thermos ....................................................................... 28
12. Cleaning water strainer ................................... 32
13. Single brew ............................................................ 33
14. Spare parts ............................................................. 34
15. Extra additions ..................................................... 35
16. Declaration of conformity..............................36
17. Warranty................................................................... 37
18. Notes .........................................................................38

Rev.100318-01-v1
6
Hipster 1grp
This appliance is intended to be used in applications such as:
- Kitchen areas, shops.
- Oces and other commercial working environments.
- Hotels, motels.
- Bed and breakfast environments.
Switch o the appliance when NOT in use.
Do not use this appliance for anything other than intended use. Any maintenance other
than cleaning should be performed by authorised person.
Do not install the machine in environments in which the temperature is 0 C or less.
Do not use outdoors.
2. Safety information
2.1 Introduction
2.2 This user manual
Information for the user:
Note!
safety instructions
This user manual is an integral part of the appliance and must be kept in an accessible
place under the working life of the appliance.
2.3 Intended use
Warning!
Electric shock hazard!
ALL ELECTRICAL
WORK MUST BE
PERFORMED
BY AN AUTHORIZED
ELECTRICIAN
Save these instructions for future reference.
Caution!
Burn hazard!
Protect your eyes.

Rev.100318-01-v1
7
Hipster 1grp
Read all the user instructions before using the machine.This guide contains important
instructions for proper and safe use of the Hipster brewer. Always keep this manual close
at hand for future reference. We reserve the right for any errors in text or images and any
necessary changes made to technical data. In the event of technical problems or any
questions. Please contact our [email protected]
The appliance is only to be installed in locations where it can be overseen by trained
personnel.
The English language is used for the original instructions .
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
The instructions shall state that access to the service area should only be permitted to
persons having knowledge and practical experience of the appliance, in particular as far as
safety and hygiene are concerned.
Indoor use.
Warning! In case of improper use the responsibility is on the user.
2.5 General safety instructions
For the optimal performance of the PULS these parameters shall not be exceeded:
Maximum permissible inlet water pressure : 800KPa (8Bar)
Minimum permissible inlet water pressure: 200KPa (2Bar)
Maximum working temperature: 40C
Minimum working temperature: 10 C
2.4 Capacity of the machine.

Rev.100318-01-v1
8
Hipster 1grp
Avoid getting the coee machine wet and do not spray liquids onto it. In the event of contact
with liquid immediately switch o the power at the socket or main breaker and dry the
appliance thoroughly.
Never immerse the machine, plug or mains cable in water because there is a danger of
electric shock.
Never try to put out a re or ames with water. Turn of the appliance and remove the plug
from the socket, and smother the ames with a re blanket or other appropriate cover.
Do not operate any electrical appliance with a damaged cord or after the appliance has been
damaged in any manner. If the mains cable is damaged it must be replaced by the customer
service to avoid a hazard.
Do not install the machine in environments in which the temperature is 0° C or less.
Do not move the Hipster brewer whilst in operation.
Do not use the Hipster brewer on a sink drain board.
Do not place the Hipster brewer on or near a hot gas or electric burner, or where it could
touch a heated oven.
Keep the appliance and accessories clean. Follow the cleaning instructions provided in this
manual.
Only use original spare parts. The use of spare parts not approved by the
manufacturer could lead to res, electric shocks or personal injury.
Do not place on top of any other appliance.
Appliance must not be cleaned by a water jet.
Electric shock hazard!
This appliance dispense hot water from the brewing hat and may cause injury if not
used correctly. The brew basket must be in place before a recipe is started.
Do not move the brew basket while the coee is being brewed.
Do not touch hot surfaces with your hands; use the handles and buttons.
Burn hazard!

Rev.100318-01-v1
9
Hipster 1grp
2.6 Disposal
Do not dispose of the device in household waste! Recycle devices, accessories and
packaging. Observe applicable national regulations.
EU only: In accordance with European Directive on waste electrical and electronic
equipment and implementation in national law, used electric power tools must be
collected separately and handed in for environmentally friendly recycling. By collecting and
recycling waste, you help save natural resources, and make sure the product is disposed in
an environmental friendly and healthy way.
Remove all packaging materials attached to your Hipster 1GRP. Ensure that you have removed
all parts and accessories before discarding the packaging.
Clean parts and accessories, lter, basket and thermos. Use warm water and a gentle dish
washing liquid and rinse well. Wipe the outer housing and drip tray with a soft damp cloth and
dry thoroughly.
3. Before rst use
Danger! Do not immerse power cord, power plug for appliance in water or any
other liquid. Do not clean any of the parts or accessories in the dishwasher.
Accept dish try. Important to clean the product propertly.
Important! Ensure that you have removed all parts and accessories before
discarding the packaging.
Note! We recommend that you save the packaging for a possible return
of goods.

Rev.100318-01-v1
10
Hipster 1grp
Touch controller
Brewer hat
Brew basket
Thermos 2,5 l
Internal water connection
4. Product description Hipster Brewer
Level tube
Coee tap
Drip tray insert
Drip tray
Adjustable feet
Brewer Tube
Water module
On/O
Foot panel
4,1 Description
Thermos 3,8 l

Rev.100318-01-v1
11
Hipster 1grp
4.2 The cycle of The Hipster taste-proling
”Regular”
brewer
Target
Pre-brew phase End phase
End phase
Time
Temperature
End phase
+ Blooming
Pre-brew phase

Rev.100318-01-v1
12
Hipster 1grp
330
665
570
Power Input
Water Inlet
5. Technical data
Including touch controller, router, cup stand and hario wire insert for single brew.
The machine is placed on the counter. Adjustable feet for levelling.
Capacity: 1x3,8 lit 200 cups/h.
Dimensions: W330mm/D570mm/H665mm.
Weight: 28 kg.
Max power hot: 230V 1x2400W.
Max power cold: 1x38W.
Max power idle: 7 W.
Water Inlet
Power Input
570mm
665mm
330mm
5.1 HIPSTER1GRP

Rev.100318-01-v1
13
Hipster 1grp
5.2 Wiring diagram TB Tube
TUBE 220 - 240 VAC 2400W

Rev.100318-01-v1
14
Hipster 1grp
Drip tray insert
Touch controller
6. Unpacking
1x 25 Coee lter 110/330
Extension cords router
Thermos 2,5 Litres
Adjustable feet x4
Drip tray
Foot panel x4
RJ hub Extension
adapter
Inlet hose
Router
Brew basket plastic
Non-return valve

Rev.100318-01-v1
15
Hipster 1grp
4.
5.
6.
3.
2.
1.
7. Installation instructions
Tools needed: Spirit-level
Adjustable spanner
ALL ELECTRICAL
WORK MUST BE
PERFORMED
BY AN AUTHORIZED
ELECTRICIAN
7.1 Description
Warning! Nr 5. CAN cable to button
The black CAN-cable is for the button controller only.
Do not connect to the router.
HIPSTER 1GRP
1. RJ45 to LAN
2. Modem
3. Power unit modem
4. Power unit Hipster
5. CAN cable to button
controller
6. Cold water in 3/4”
with JG 8mm and
Non-return valve
Hipster Brewer 1 GR
Important! Nr 6.
When fasten the non-return
valve; make sure that the
arrow is in the right direction.
(toward the machine).

Rev.100318-01-v1
16
Hipster 1grp
7.2 Adjust the feet
7.3 Adjust the brewer hat in level.
Caution! Make sure the brewer hat is in level, or it will not
extract evenly in the lter basket. Use a spirit-level .

Rev.100318-01-v1
17
Hipster 1grp
7.4 Connect the water lter system.
7.5. Connect the network-cable.
(RJ45) white cable. To the LAN-port of the router.
1. Start the router 1 minute before the coee machine, to get an IP-address.
2. Start the machine. Press ON button.
3. A short beep sound means the brewer is on.
4. After 3-8 sec long beep means that the brewer have received an IP-address.
5, Start a run cold. 300-400 ml will be dispensed,
Note! See manual with the lter set.

Rev.100318-01-v1
18
Hipster 1grp
6. Temperature calibration must always be done before brewing is started.
( CAL 1 and CAL2)
7. Place a container that takes more than 2 litres under the lter basket.
8. Alternative 1. Push the menu-button in the upper left corner, choose Tools then Special
Routines.
Alternative 2. Using the button controller with display, push the lower right button,
”Setup”.
9. Run Calibrate 2. 2,0lit of hot water is dispensed.
10. Run Calibrate 1. 1,8lit of hot water is dispensed.
11.Now the Hipster 1GRP is installed. You are now ready to brew! See page 19.
Warning! Nr 6. Very important! Otherwise the system might overheat.
Note! For 3TEMP to be able to support you in the best possible way,
please connect your Hipster to the internet via LAN, WLAN or GSM.
Use tethering on the router and connect to your existing Wi-Fi.
If you need support, please send us an email to [email protected] or call your
nearest support.
If you want to give us feedback on the product; please send us an email to
inf[email protected]
0. O
1. Startup Flashing light
2. Idle Green
4. Running Blue
16. Heater Error Red slow ash
19. Connector error Red fast ash
20. Water supply Error Red fast ash
State number State name Light
7.6 Machine status

Rev.100318-01-v1
19
Hipster 1grp
8.1 Prepare a brew
3. Add lter to the brew basket.
1. Place the thermos under the brew basket.
8. User instructions
2. Remove the brew basket from
the brew hat.
4. Add coee into the lter.
Note! Make sure the lter ts correct.
Use 3TEMP coee lter paper.
Note! Make sure the coee is spread
evenly and the surface is at.
Danger! Can cause serious burns. Do not remove the brew basket when lamp is
blue and brewing.

Rev.100318-01-v1
20
Hipster 1grp
5. Reinstall the brew basket. 6. Ready to brew.
8.2 Select recipe
2. Adjust grams or millilitre. If needed.1. Select a recipe.