3xLogic VX-2S-D4-RIA User manual

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
1
VISIX S-Series Indoor IP Dome Camera
VX-2S-D4-RIA Quick Start Guide
v01-2019

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
2
Table of Contents
1 CAMERA OVERVIEW...................................................................................................................................... 3
PACKAGE CONTENTS ...................................................................................................................................... 3
Available Mounts........................................................................................................................................... 3
INSTALLATION ............................................................................................................................................... 4
Removing Dome ............................................................................................................................................ 4
Installing the MicroSD Card ........................................................................................................................... 4
Installing The Camera - Cabling Routed Through Base ................................................................................. 5
Installing The Camera — Cabling Routed Through Side ............................................................................... 6
Installation – Cabling and Safety Wire .......................................................................................................... 7
Installation – Finalizing Installation............................................................................................................. 10
2 CAMERA SETUP ........................................................................................................................................... 11
DETECTING,ACTIVATING CHANGING THE CAMERA IP ADDRESS ............................................................................ 11
1.1 ADDING A VISIX S-SERIES CAMERA TO VIGIL SERVER............................................................................................ 12
1.2 ACCESS UI VIA WEB BROWSER .......................................................................................................................... 14

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
3
1Camera Overview
Package Contents
Please see the descriptions of the camera’s box contents.
Number Description
1Camera
2Mounting Base
32x Installation Hardware (screws and anchors)
4T20 Torx Key
NOTE: Press and hold RESET for 10s when the camera is powering on or rebooting to restore the default
settings, including the user name, password, IP address, port No., etc.
AVAILABLE MOUNTS
VX-WM-D2: Wall Mount Adaptor
VX-PM-D2: Pendant Mount Adaptor
VX-FM-D2: Indoor Ceiling Flush-Mount Adaptor
VX-POLE: Pole Mount Adaptor
VX-CM: Corner Mount Adaptor
VX-WMJ-D2: Wall Mount Adaptor with Junction Box
T20
1
2
3
4

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
4
Installation
REMOVING DOME
1. Use the supplied torx key to unscrew the three fastening points for the dome.
2. Lift the dome to remove it from the camera chassis.
INSTALLING THE MICROSD CARD
Steps:
1. Use the supplied hardware to unfasten the dome screws and remove the from the chassis.
2. Insert the microSD card into the available reader slot.

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
5
INSTALLING THE CAMERA - CABLING ROUTED THROUGH BASE
Steps:
1. Use a pencil and the mounting base to mark the drilling points and the cable hole on the installation
surface.
2. Drill the cable hole and anchoring points into the installation surface.
3. Insert the anchors.
4. Route the cablings harness through the center cable hole.
5. Use a Philipps-head screwdriver to fasten the mounting base to the installation surface.
6. Proceed to Installation – Cabling and Safety Wire for next steps. .
5.0

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
6
INSTALLING THE CAMERA — CABLING ROUTED THROUGH SIDE
Steps:
1. Use a pencil and the mounting base to mark the drilling points on the installation surface.
2. Drill the anchoring points into the installation surface.
3. Insert the anchors.
4. Use a screwdriver to fasten the mounting base to the installation surface.
5. Proceed to Installation – Cabling and Safety Wire for next steps.
5.0

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
7
INSTALLATION – CABLING AND SAFETY WIRE
1. If routing the cable through the base of the camera, route the cabling through the hole you drilled in
the installation surface (A). If you are routing the cable through the side of the camera, no action is
required (B).
2. Attach the safety cable to the clip located on the camera mounting base.

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
8
3. Attach the GND wire to the grounding point using a Philipps screwdriver.
4. Remove the alarm and power blocks from the camera.
5. Wire the alarm and power blocks as necessary. Available wiring and inputs / outputs may vary
depending on your camera model.

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
9
6. Connect all cabling (Audio In / Out, RJ-45, etc…) and reattach the wired alarm and power blocks to the
camera.
7. If you are routing cabling through the base of the camera, proceed to Installation – Finalizing
Installation. If routing through the side of the camera chassis, remove the cabling plug and route the
cabling harness through the side.

S-Series Camera Quick Start Guide | VX-2S-D4-RIA
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
10
INSTALLATION – FINALIZING INSTALLATION
1. Secure the camera body to the mounting base aligning the camera and base using the indicators then
pushing and turning the camera body counter-clockwise into the base until snug.
2. Use the provided torx key to secure the camera body to the base.