4KDVB CV-F01-TX User manual

CV-F01-TX UserManual
1
Fiber Optic Extender User Manual
Model: CV-F01-TX
1. I/O Connectors
Figure 1 CV-F01-TX Fiber Optic Transmitter I/O Connectors
2. Connection introduction
Figure 2 CV-F01-TX Fiber Optic Transmitter Connection
Note: Please connect one single-mode optical fiber to the TX port in the fiber optic connector.
3. DIP Switch
Dial up is “OFF”, the corresponding number is “1”; dial down is “ON”, the corresponding
number is “0”. The DIPswitch operating instructions as shown in Table 1. And the DIP switch

CV-F01-TX UserManual
2
setting and the corresponding output mode and resolutions as shown in Table 2.
Table 1 DIP switch operation instruction
Table 2 DIP switch setting and the corresponding output mode and resolutions
Output Resolution & Mode
Dial Switch 1
Dial Switch 2
Corresponding
Binary Code
Output: 800×600
Signal Source: Input 1
OFF
OFF
11
Output: 800×600
Signal Source: Input 2
ON
OFF
01
Output: 1600×900
Signal Source: The two signal
sources are divided into left and
right to display
OFF
ON
10
Output: 1600×600
Signal Source: The two signal
sources are divided into left and
right to display
ON
ON
00
Note: Default output mode and resolution canbe configured through the serial port.
4. Indicator Light
Table 3 Indicator light and signal state
Light State
L1 flash
L2 on/off
L3 on/off
Description
The CV-F01-TX
works normally
on: Input 2 has signal
off: No signal in Input 2
on: Input 1 has signal
off: No signal in Input 1
DIP
Item
Description
Dial both switch 1
and switch 2
Function
To set output mode and resolution.
Applying Condition
Before applying power to the CV-F01-TX or
during the service of the item.
Operation
Dialing combination of the DIP switch and
the corresponding resolutions as shown in
table 2.
Dial only switch 3
Function
To set input standard of CVBS.
Applying Condition
Before applying power to the CV-F01-TX or
during the service of the item.
Operation
Dial OFF: PAL standard
Dial ON: NTSC standard
Dial only switch 4
Function
To set the functions of RS232 serial port.
Applying Condition
Before applying power to the CV-F01-TX or
during the service of the item.
Operation
Only OFF is available.

CV-F01-TX UserManual
3
5. Audio Input
The CV-F01-TX supports two 3.5mm ear jack interface line audio transmission, need to
add embedded binding CVBS video signal transmission;
Please note that twoaudio canbe transmitted separately.
CVBS transmission without audio is available.
Audio input canbe configured through the serial port.
6. Applying Power
First, please make sure that all the connection is fine.
Second, make all the configuration completed according to your specific needs.
Third, applying stable 12V/2A power toboth the transmitter and the receiver.
7. OSD Setting
Step1: Connect the CV-F01-TX to the control computer Connect the CV-F01-RXto the
control computer by using the DB9 pin RS232 female cross serial line with the item.
Step2: Putthe CD into the control computer and decompress the configuration tool folder
that burned in the CD and install the tool. (Youcan also ask the technical specialist for the
configuration tool folder.)
Step 3: Double click the configuration tool will enter into the Communication
Setting interface. Select serialport and baud rate as shown in figure 3. After that, click the
OK button.
Figure 3 Communication setting interface

CV-F01-TX UserManual
4
Step4: OSD setting main interface will show up after click the OK button in step3. OSD
setting is available in text andimage mode.
Image size is required to be less than 16K.
Text should not exceed the software preview display.
Image format is available in bmp, jpg and jpeg.
Color setting is available in background and foreground.
Details as shown in figure 4.
Figure 4 OSD setting main interface
Image mode setting steps are as follows:
Step1: Select the input port.
Step2: Click the checkbox which is in front of the Enable OSD.
Step3: Select the background image according to your needs. Please note that this step is
optional.
Step4: Set the color of image.
Step5: Set the location andthe size of image.
Step6: Select the magnification.
Step7: Click the Download button and the setting will come into effect immediately.
The details as shown in figure 5.

CV-F01-TX UserManual
5
Figure 5 Image mode setting steps
Text mode setting steps are as follows:
Step1: Select the input port.
Step2: Click the checkbox which is in front of the Enable OSD.
Step3: Design the text content according to your needs.
Step4: Set the color of text.
Step5: Set the location andsize.
Step6: Select the magnification.
Step7: Click the Download button and the setting will come into effect immediately.
The details as shown in figure 6.

CV-F01-TX UserManual
6
Figure 6 Text mode setting steps
Note:
If OSD setting is not required, please uncheckthe option which is in front of the Enable
OSD.
The crossover serial cable with DB9 pin female connector is needed.
8. Parameter Setting
The CV-F01-TX is available in audio input selection, image display setting and port
parameter setting through the configuration tool.
Audio input is available in Input 1 or input 2.
Image display mode can be controlled by the configuration tool orDIP switch.
Brightness, chorma, saturability, contrast and mode setting are available.
The details as shown in figure 7.

CV-F01-TX UserManual
7
Figure 7 Parameter setting interface
Note:
If you would like to checkthe current state ofthe item, please click the Load button.
If the control mode is Dial Switch, the resolution of the item canbe configured by DIP
switch directly.
The important and commonly used OSD information canbe savedto the local computer
software tofacilitate later use through the configuration tool.