7inova 7R152 User manual

Before you start to use this device, please check if there’s anything
missing in the package, and contact your dealer of purchase to
claim for missing items:
Package Contents:
1x 7R152 Wifi Repeater
1x 1m Ethernet cable with RJ45 connector
1x Quick Installation Guide
Wireless-11N WallMounted Wifi Router 300M
Quick Installation Guide
Model：7R152
LED indicators’ Status Description:
WPS Button
Ethernet
Reset Button
WLAN LED
WPS LED
Ethernet LED
Power LED
Euro plug
Cautions:
1. Disconnect the device in thunderstorms in case of lightning damage.
2. Keep far from heat source and ensure ventilation.
3. Keep waterproof in the storage, transportation and operating environment.
Indicator Name
Power Status Indicator
Wireless Status Indicator
WPS Status Indicator
Ethernet Status Indicator
Green On Get Powered
Green slow blink Wireless Function Launched
Green fast blink
Not bright
WPS Function Launched
Not use or have
completed the connection
Green fast blink
Green fast blink
Green On
Data Transmission via Ethernet
Ethernet Connected
Data Transmission via wireless
Status Description
Reset: If need to reset the router, press and hold RESET button for 3-5
seconds, release until all other LED are off except Power LED.
Note: Please check whether the WiFi-Router accord with factory default settings
once you can’t download http://192.168.2.1. If you are still not sure what reasons,
you can reset the WiFi-Router, just need to press the reset button for 3-5 seconds,
then try again.
Appearance Introduction
1 Computer Configuration
3 Configuration Mode
2 Connect To Wireless Network
1.1 Click “Start→Control Panel→Network and Internet→Network and Sharing
Center→Change adapter settings→Wi-Fi(right click)→Properties”
3.1.1 After logging in and click “Operating Mode”, you will see 3 modes:
Select “Bridge” then click on “Save”
3.2.5 Setup your info and click on “Next”
3.2.6 Click “Finish” wait for a few, then accord to “4 Reconnect to Router”
to reconnect the router.
3.1 Configure Bridge Mode
3.2.3 Wait a few seconds, then refresh the Browser. Select “Setup Wizard”,
then click on “Next” to continue.
3.2.4 You will see “WAN Connection Type”: Static IP / DHCP / PPPoE /
L2TP / PPTP.
Static IP: Select “Static IP” and input the network’s IP address information,
then click “Next”
3.2.1 Follow process 2.3 to 2.4.
3.2.2 Select “Router” then click on “Save”.
3.2 Configure Router Mode
2.1 Pulg the Wi-Fi Router to a wall socket.
2.2 Click on the network icon( ) on the right
bottom of your desktop. You will find the signal
from the Wi-Fi Router. Click on “Connect” and
wait for a few seconds.
2.4 The login screen below will appear.
Enter the “Username” and “Password”
then click “Login” to login. The default
Username is “admin” and Password is
“admin”.
2.3 Open web browser and type http://192.168.2.1 in the browser’s address
box. This number is the default IP address for this devices.
1.2 Double click “Internet Protocol Version 4(TCP/IPv4)”
1.3 To set up the computer IP 192.168.2.x (x arbitrary integer between
2~252), subnet mask of 255.255.255.0, Click “OK”. Back to the last
interface and click “OK”
01 Wireless-N Router 02 Wireless-N Router 03 Wireless-N Router
05 Wireless-N Router04 Wireless-N Router 06 Wireless-N Router 07 Wireless-N Router
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
3.2.7 Select “DHCP” and click “Next”, then follow process 3.2.5 to 3.2.6
3.2.8 Select “PPPoE” and fill your Username and Password provided by
network operator.
Follow process 3.2.5 to 3.2.6 after click “Next”.
300Mbps Wireless Router
FW RVE: 7R152_V1.0

300Mbps Wireless Router
FW RVE: 7R152_V1.0
1) Restore the 7R152’s configuration to its factory default settings. (With
7R152 powered on, use a pin to press and hold the Reset button for
about 3-5 seconds before releasing it).
2)To log in the Web Management page, use the default user name and
password: admin, admin. To connect to the Wireless Network, use the
default password on the label.
3)Try to configure 7R152 once again by following the instructions in the
previous steps of the QIG.
What can I do if I forgot my password?
Appendix: Troubleshooting
3.3.1 Follow process 2.3 to 2.4
3.3.2 Select “Repeater” then click “Save”
3.3.4 Select your Wireless SSID to continue.
3.3.5 When you see the site below, please do not change any setting but
only insert the key of your network.
Click on “Apply” wait for a few, then accord to “4 Reconnect to Router” to
reconnect the router
3.3.3 Select “Wireless Settings → Wireless Basic Settings”, click “Search”
then you will see the new page.
3.3 Configure Repeater Mode
5.2 Wireless Security Configuration
4 Reconnect to Router
4.1 Click “Start→Control Panel→Network and Internet→Network and Sharing
Center→Change adapter settings→Wi-Fi(right click)→Properties”
5 Configuring via Web Browser
5.1 Wireless Base Configuration
4.2 Double click “Internet Protocol Version 4(TCP/IPv4)”
4.3 Select “Obtain an IP address automatically” and “Obtain DSN
server address automatically”. Click “OK”. Back tothe last
interface and click “OK”
4.4 Select the wireless network name
configured in “3 Configuration Mode” ,
click “Connect” button.
4.5 If you encrypted wireless network in
“3 Configuration Mode”, the following
message will be displayed on web
browser, fill in password, click “OK”
Please click “Wireless Settings → Wireless Basic Settings” located at
the web management interface, the following message will be displayed
on your web browser:
You could configure the minimum number of Wireless settings for
communication, such as SSID and Channel. The Access Point can be set
simpty with only the minimum setting items.
Please click “Wireless Settings → Wireless Security Settings” located
at the web management interface, the following message will be displayed
on your web browser:
Setup the wireless security and encryption to prevent from unauthorized
access and monitoring. Supports 64/128-bit WEP, WPA-Personal, WPA2-
Personal encryption methods.
5.3 Change Management password
Default password of Wireless Router is “admin”, and it’s displayed on the
login prompt when accessed from web browser. There’s a security risk
you don’t change the default password, since everyone can see it. This is
very important when you have wireless function enabled.
To changepassword, please follow the following instruction:
Please click “System Tools →Password” menu on the web management
interface, the following message will be displayed on your web browser:
5.4 Firmware Upgrade
The system software used by this router is called as “firmware”, just like
any applications on your computer, when you replace the old application
with a new one, your computer will be equipped with new function. You
can also use this firmware upgrade function to add new functions to your
router, even fix the bugs of this router.
Please click “System Tools → Firmware Upgrade” located at the located
at the web management interface, then the following message will be
displayed on your web browser.
5.5 Settings Backup and Restore, Factory Default
You can backup all Setting of this router to a file, so you can make several
copied of router configuration for security reason.
To backup or restore router setting, please follow the following instruction:
Please click “System Tools → Backup and Restore” and “System
Tools → Factory Default” located at the web management interface,
then the following message will be displayed on your web browser:
If you want to keep original password unchanged, click “Cancel”.
Click “Save” button, the WiFi Router will become effective
Click “Browse” button first, you’ll be prompted to provide the filename of
firmware upgrade file. Please download the latest firmware file from our
website, and use it to upgrade your router.
After a firmware upgrade file is selected, click “Upgrade” button, and the
router will start firmware upgrade procedure automatically.
The procedure may take several minutes, please be patient.
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
Wireless Status
SSID
Wireless Mode
Channel
SSID Broadcast
Wireless On/Off
Main Service Set Identifier.
It’s the “name” of your wireless network.
Supports 11b/g/n mixed modes
Wireless Signal On/Off
6(default)
Back up
Browse
Restore All Settings
Press ”Back up” button, you can please save it as another
filename for different versions, and keep it in a safe place.
Press ”Browse” to pick a previously-saved configuration file
from your computer, and the click “Save”. After the replaced
by the file you just uploaded.
Click “Restore All Settings” button to remove all settings
300Mbps Wireless Router
FW RVE: 7R152_V1.0
Note: Never interrupt the upgrade procedure by closing the web browser or
physically disconnect your computer from router. If the firmware you upgrade is
corrupt, the firmware upgrade will fail, and you may have to return this router to
the dealer of purchase to ask for help. (Warranty voids if you interrupted the
upgrade procedure).
Click “Save” and “Restore All Settings” button. The router will restart.
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
09 Wireless-N Router08 Wireless-N Router 10 Wireless-N Router 11 Wireless-N Router
13 Wireless-N Router12 Wireless-N Router 14 Wireless-N Router 15 Wireless-N Router
300Mbps Wireless Router
FW RVE: 7R152_V1.0
300Mbps Wireless Router
FW RVE: 7R152_V1.0
Click “Apply” button, the WiFi Router will become effective.