A-Neuvideo ANI-44HPSC User manual

AUDIO / VIDEO MANUFACTURER
ANI-44HPSC
4K UHD+ 4X4 MATRIX W/ AUDIO OUTPUT
INSTRUCTION MANUAL
A-NeuVideo.com
Frisco, Texas 75036

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power o󰀨 and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect Input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the Inputs with a signal level greater than that required to drive equipment to full Output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS
ANEUVIDEO
1
CONTENTS
INTRODUCTION & CONTENTS ................................................1
FEATURES & SPECIFICATIONS ...............................................2
OPERATION CONTROLS & FUNCTIONS .................................3
REMOTE CONTROL ....................................................................5
PINOUT DIAGRAMS / CABLE SPECIFICATIONS ....................6
FRONT PANEL LCD MENU ........................................................7
WEBGUI CONTROL .................................................................11
TELNET CONTROL ..................................................................15
CONNECTION DIAGRAM .......................................................18
VIDEO & AUDIO SPECIFICATIONS.........................................19
INTRODUCTION
This 4K UHD+ 4x4 HDMI Matrix provides the ability to connect up
to (4) 4K UHD+ HDMI sources to up to (4) 4K UHD+ HDMI displays
and freely switch between them. This unit comes with full support for
18Gbps resolutions up to, and including 4K@60Hz (4:4:4, 8-bit) as
well as support for 16-bit Deep Color, HDR (High Dynamic Range),
HD audio and other features dened by the HDMI 2.0 specication.
With a comprehensive EDID management feature that includes
the ability to select between built in EDIDs, EDIDs copied from
connected sink devices, as well as user provided EDIDs, this matrix
can solve many interconnectivity problems. The unit’s OSD has the
ability to display up to 2 lines of user customized text, on top of the
video displayed over each output, in the color of your choice. This
unit provides an intuitive set of front panel controls with an OSD as
well as RS-232, Telnet, WebGUI, and IR remote control options.
This product has a 3 year warranty.
PACKAGE CONTENTS
• ANI-44HPSC UHD+ 4x4 HDMI Matrix with Audio Output
• 24V/2.7A DC Power Adapter
• Remote Control
• Rackmount Ears (Set of 2)
• Shockproof Feet (Set of 4)
• Users Guide
SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or
audio ampliers.
• The use of Premium High Speed HDMI cables is highly
recommended.
APPLICATIONS
• Residential or commercial AV matrix installations
• Security systems
• Lecture halls and ballrooms
• Retail product showrooms
• Control centers
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
w(8) to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
su󰀩cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2020. All Rights Reserved.
Version 1.0 JAN 2020
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATURES & SPECIFICATIONS
FEATURES
• HDMI inputs and outputs support 18Gbps 4K UHD+ with HDR signals
• DVI 1.0 compliant with the use of an HDMI to DVI adapter
• HDCP 1.x and 2.2 compliant
• HDMI inputs and outputs support UHD+ resolutions up to 4096x2160@60Hz (4:4:4, 8-bit)
• Supports 16-bit Deep Color up to 1080p60
• Supports pass-through of LPCM (up to 8 channels), bitstream and HD bitstream audio formats
• High-quality DAC (Digital to Analog audio Conversion) with local analog stereo audio breakout for each HDMI output (LPCM 2.0
sources only)
• Supports (6) internal EDIDs, (4) external EDIDs copied from connected devices, and (4) user provided EDIDs
• OSD with user customizable information text
• Controllable via front-panel buttons with LCD, WebGUI, Telnet, RS-232, and IR remote
SPECIFICATIONS
• HDMI Bandwidth: 18Gbps
• Input Ports: (4) HDMI (Type-A)
• Output Ports
• (4) HDMI (Type-A)
• (4) Analog Stereo (3.5mm)
• Control Ports
• RS-232 (DE-9)
• Ethernet (RJ-45)
• IR Extender (3.5mm)
• Service Port: USB 2.0 (Type A)
• IR Frequency: 38kHz
• Baud Rate: 19200
• Power Supply: 24V/2.7A DC (US/EU standards, CE/FCC/UL certied)
• ESD Protection (HBM):
• ±8kV (Air Discharge)
• ±4kV (Contact Discharge)
• Dimensions (WxHxD): 17.2 x 1.9 x 10.6 in (438x49x269mm) [Case Only] / 19 x 1.9 x 10.8 in (482x49x274mm) [All Inclusive]
• Weight: 6.6lb / 2.99kg
• Chassis Material: Metal (Steel)
• Chassis Color: Black
• Operating Temperature: 0˚C – 40˚C/32˚F – 104˚F
• Storage Temperature: -20˚C – 60˚C/-4˚F – 140˚F
• Relative Humidity: 20 – 90% RH (Non-condensing)
• Power Consumption: 34W
As product improvements are continuous, specications are subject to change without notice.
ANEUVIDEO

3
OPERATION CONTROLS & FUNCTIONS
FRONT PANEL
qPOWER BUTTON: Press this button to power the unit on (green LED) or place it into stand-by mode (red LED).
wIR RECEIVING WINDOW: Accepts IR signals from the included IR remote for control of this unit only.
eIN 1~4 & OUT A~D BUTTONS: Press the “OUT” keys (A~D) of the outputs you wish to route a source to (they will ash to indicate
selection). Next, press the “IN” key of the input (1~4) you wish to route to the selected outputs. Finally, press “CONFIRM” to conrm your
selection and execute the routing change.
rCONFIRM BUTTON: Press this button to conrm newly made input/output routing selections.
CANCEL BUTTON: Press this button to cancel newly made input/output/preset routing selections before they have been conrmed.
t MENU BUTTON: Press to enter the LCD menu, or to back out from menu items.
ENTER BUTTON: Press to conrm a selection within the LCD menu or to go deeper into a menu item.
+ (PLUS) & - (MINUS) BUTTONS: Press to move up and down or adjust selections within the LCD menu.
yALL BUTTON: Press this button to select all outputs simultaneously for routing. Next, press the “IN” key of the input (1~4) you wish
to route to all outputs. Finally, press “CONFIRM” to conrm your selection and execute the routing change.
uPRESET BUTTON: Press to enter the preset recall menu in the LCD window. Press the “+/-” buttons followed by the “ENTER” button
to select and activate the preferred preset.
iLOCK BUTTON: Press to lock all button functions on the front panel. Press and hold for 3 seconds to release the lock function. The
LCD will display “Lock” when the function is active.
oMUTE BUTTON: The “MUTE” button functions as a blank audio/video source. To use it, follow the standard matrix routing instructions,
but use the “MUTE” button as the input to blank out the selected outputs. When a “MUTE” input is in use it will show up as “M” within
the routing display.
Note: The associated analog output will not be muted.
aLCD WINDOW: Displays the unit’s menu, settings and information.
ANEUVIDEO

4
OPERATION CONTROLS & FUNCTIONS
Rear Panel
qHDMI IN 1~4 PORTS: Connect to HDMI source equipment such as media players, game consoles or set-top boxes.
wAUDIO/HDMI OUT A~D PORTS: Connect the HDMI outputs to devices such as HDMI TVs, monitors or ampliers for digital video and
audio output. Connect the audio outputs to powered speakers or an amplier for analog stereo audio output. The audio from each stereo
analog output will be the same as the HDMI output it is paired with.
eSERVICE PORT: This slot is reserved for rmware update use only.
rCONTROL PORT: Connect directly, or through a network switch, to your PC/laptop to control the unit via Telnet/WebGUI.
tRS-232 PORT: Connect directly to a PC, laptop or other serial control device to send RS-232 commands to control the unit.
yIR IN PORT: Connect to the provided IR Extender to extend the IR control range of the unit. Ensure that the remote being used is within
direct line-of-sight of the IR Extender.
uDC 24V PORT: Plug the 24V DC power adapter into the unit and connect it to an AC wall outlet for power.
ANEUVIDEO

5
Remote Control
Remote Control
ANEUVIDEO
qPOWER BUTTON: Press to power the unit on or place it into stand-by mode.
w1/A ~ 4/D BUTTON: Press these keys to congure the video routing. Press the “-/
OUT” key followed by the key (A~D) of the outputs you wish to route a source to (they will
ash on the LCD to indicate selection). Next, press the “+/IN” key followed by the input
(1~4) you wish to route to the selected outputs. Finally, press “ENTER” to conrm your
selection and execute the routing change.
Note: Buttons 5/E~8/H have no function with this matrix.
eALL BUTTON: Press this key to select all outputs simultaneously for routing. Next,
press the key of the input (1~4) you wish to route to all outputs. Finally, press “ENTER”
to conrm your selection and execute the routing change.
MUTE BUTTON: Press this key to mute video output. Press the key of the input (1~4)
you wish to route then press mute key to mute video output.
INFO BUTTON: Switches the information displayed on each output’s OSD between the
user customized text and the current video/Ethernet details.
PRESET BUTTON: Press to enter the preset call menu in the LCD window. Press the
“+/IN” and “-/OUT” buttons followed by the “ENTER” button to select and activate the
preferred preset.
rMENU BUTTON: Press to enter the LCD menu, or to back out from menu items.
ENTER BUTTON: Press to conrm a selection within the LCD menu or to go deeper into
a menu item.
CANCEL BUTTON: Press to cancel newly made input/output/preset routing selections
before they have been conrmed.
+ (PLUS)/IN BUTTON: Press to navigate up within menus or to begin the selection of
an input for routing.
- (MINUS)/OUT BUTTON: Press to navigate down within menus or to begin the selection
of outputs for routing.

6
Pinout diagrams / Cable Specifications
RS-232 Pinout and Defaults
Serial Port Default Settings
Baud Rate 19200
Data Bits 8 bits
Parity Bits None
Stop Bits 1
Flow Control None
IR Cable Pinout
Cable Specifications
CABLE LENGTH
1080p 4K30 4K60
8-BIT 12-BIT (4:4:4) 8-BIT (4:4:4) 8-BIT
HIGH SPEED HDMI CABLE
HDMI Input 49 ft / 15M ~33 ft / 10M 16 ft / 5M ~10 ft / 3M
HDMI Output 49 ft / 15M ~33 ft / 10M 16 ft / 5M ~10 ft / 3M
Bandwidth Category Examples:
• 1080p (FHD Video)
- Up to 1080p@60Hz, 12-bit color
- Data rates lower than 5.3Gbps or below 225MHz TMDS clock
• 4K30 (UHD Video)
- 4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit color
- Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps
• 4K60 (UHD+ Video)
- 4K@50/60Hz (4:4:4, 8-bit)
- 4K@50/60Hz (4:2:0, 10-bit HDR)
- Data rates higher than 10.2Gbps
ANEUVIDEO

7
Front Panel LCD Menu
Front Panel LCD Menu
All primary functions of this unit can be controlled by using the front panel LCD menu which is activated
by pressing the MENU button on the front of the unit. Use the + (PLUS), − (MINUS), and ENTER buttons
to navigate the LCD menu. Press the MENU button to back out from any menu item and then press it
again to close the menu.
The individual functions of the LCD menu will be introduced in the following section. Items marked in
BOLD are the factory default settings.
1. IN 1~4: Select the EDID to assign to each input independently. (6) internal
EDIDs, (4) sink EDIDs and (4) user EDIDs are available. Press the “Enter”
button to conrm the selection. After making a selection the change will occur
immediately on that input.
Note: After changing the EDID on an input, the video will typically black out
briey while the source adjusts to the new information.
ANEUVIDEO
MAIN MENU
EDID
Preset Setup
Network Status
Network Setup
OSD Setup
CEC Send
Firmware
Firmware Update
Factory Reset
EDID
2ND LEVEL 3RD LEVEL
In 1~4 01 FHD 2Ch
02 FHD MCh
03 UHD 2Ch
04 UHD MCh
05 UHD+ 2Ch
06 UHD+ MCh
07 Sink A
08 Sink B
09 Sink C
10 Sink D
11 User 1
12 User 2
13 User 3
14 User 4

8
ANEUVIDEO Front Panel LCD Menu
2. IN ALL: Select the EDID to assign to all inputs. (6) internal EDIDs, (4) sink
EDIDs and (4) user EDIDs are available. Press the “Enter” button to conrm
the selection. After making a selection the change will occur immediately on
all inputs.
Note: This setting will override any independently set EDID selections.
1. PRESET SETUP: Select the number of the preset to store the current
routing conguration into. Press the “Enter” button to conrm the selection.
After saving the preset, the stored routing will be displayed on the LCD. Press
the “Menu” button to return to normal operation.
1. NETWORK STATUS: Displays the unit’s current networking
information or status for each item.
EDID
2ND LEVEL 3RD LEVEL
In All 01 FHD 2CH
02 FHD MCh
03 UHD 2Ch
04 UHD MCh
05 UHD+ 2Ch
06 UHD+ MCh
07 Sink A
08 Sink B
09 Sink C
10 Sink D
11 User 1
12 User 2
13 User 3
14 User 4
PRESET SETUP
2ND LEVEL 3RD LEVEL
1~4 [Store Preset]
NETWORK STATUS
2ND LEVEL 3RD LEVEL
Link: [Current link status]
Mode: [Current network mode]
IP: [Current IP address]
Mask: [Current netmask]
Gate: [Current gateway address]
MAC: [MAC address]

9
ANEUVIDEO Front Panel LCD Menu
1. MODE: Set the unit to Static or DHCP mode. When DHCP mode is
selected, all IP address information will be assigned automatically by the
local DHCP server. When Static is selected, the IP address, netmask
and gateway must be set manually and additional menu items become
available.
2. IP: When DHCP is o󰀨, the IP address can be set here. Press the
“Enter” button to begin editing the address and use the “+” and “-”
buttons to adjust each value. Press the “Enter” button to store the current
number segment and move to the next segment.
Note: The unit’s default static IP address is 192.168.1.50.
3. MASK: When DHCP is o󰀨, the netmask can be set here. Press the
“Enter” button to begin editing the address and use the “+” and “-”
buttons to adjust each value. Press the “Enter” button to store the current
number segment and move to the next segment.
4. GATE: When DHCP is o󰀨, the gateway address can be set here. Press
the “Enter” button to begin editing the address and use the “+” and “-”
buttons to adjust each value. Press the “Enter” button to store the current
number segment and move to the next segment.
1. OUT A~D: Enable or disable the OSD banner on each output. The
change will occur after “Enter” has been pressed on a changed selection.
1. OUT A~D: Pick the preferred output port using the “+” and “-” buttons
and then press the “Enter” button to select it. Using the “+” and “-”
buttons, pick the appropriate CEC command to send to the display
connected to the selected output port.
■ On/O󰀨: Turn the connected display on or o󰀨.
■Vol +/Vol -: Increase or decrease the volume of the connected
display.
■Mute: Mute the audio output of the connected display.
Note: Not all displays can support all CEC commands.
NETWORK SETUP
2ND LEVEL 3RD LEVEL
Mode: STATIC
DHCP
IP: [Current static IP address]
Mask: [Current netmask]
Gate: [Current gateway address]
OSD SETUP
2ND LEVEL 3RD LEVEL
Out A OFF
On
Out B OFF
On
Out C OFF
On
Out D OFF
On
CEC SEND
2ND LEVEL 3RD LEVEL
Out A~D On
O󰀨
Vol +
Vol -
Mute

10
ANEUVIDEO Front Panel LCD Menu
1. FIRMWARE: Displays the unit’s current rmware version.
1. DO USB UPDATE: Selecting “Yes” will prepare the unit to update
rmware via the USB port. After inserting a USB thumb drive containing
a valid rmware le (*.bin format) the update process will begin. After
completion the unit will automatically reboot.
1. DO FACTORY RESET: Selecting “Yes” will perform a factory reset
and return the unit to its factory default state. After the reset is complete,
the unit will reboot automatically.
FIRMWARE
2ND LEVEL 3RD LEVEL
Firmware [Current rmware version]
FIRMWARE UPDATE
2ND LEVEL 3RD LEVEL
Do USB Update? NO
Yes
FACTORY RESET
2ND LEVEL 3RD LEVEL
Do Factory Reset? NO
Yes

11
WebGUI Control
Device Discovery
Please obtain the “Device Discovery” software from your authorized dealer and save it in a directory where you can easily nd it.
Connect the unit and your PC/Laptop to the same active network and execute the “Device Discovery” software. Click on “Find Devices
on Network” and a list of devices connected to the local network will show up indicating their current IP address.
Note: The unit’s default IP address is 192.168.1.50.
By clicking on one of the listed devices you will be presented with the network details of that particular device.
1. IP MODE: If you choose, you can alter the static IP network settings for the device, or switch
the unit into DHCP mode to automatically obtain proper network settings from a local DHCP
server. To switch to DHCP mode, please select DHCP from the IP mode drop-down, then click
“Save” followed by “Reboot”.
2. WEBGUI HOTKEY: Once you are satised with the network settings, you may use them to
connect via Telnet or WebGUI. The network information window provides a convenient link to
launch the WebGUI directly.
WebGUI Overview
After connecting to the WebGUI’s address in a web browser, the login screen will appear.
Please enter the appropriate user name and password then click “Submit” to log in.
Note: The default user name and password is “admin”.
On the left side of the browser you will see the following menu tabs where all primary functions
of the unit are controllable via the built in WebGUI. The individual functions will be introduced
in the following sections.
Clicking the red “Logout” tab will automatically log the currently connected user out of the
WebGUI and return to login page.
ANEUVIDEO

12
WebGUI Control
Switch Tab
This page provides video routing settings, preset
saving/loading, and I/O renaming options. To begin
assigning a new video route, please click the button of
the HDMI output you wish to send video to and then
click on the button of the preferred HDMI input port. If
desired, you may select more than one output prior to
selecting the input. As you select each button they will
change their color to orange. The new route will become
active immediately after selecting the input port and the
routing information displayed on the buttons will change
accordingly.
1. OUTPUT: Buttons for selecting the output (A~D) to route A/V Inputs to. Details about the output names and currently selected Input
are also displayed here. Clicking on the “edit” icon ( ) opens up the Edit Output window which allows for changing a variety of settings
related to the video output.
■Video Mute: Each output can be individually muted (black video, no audio). To mute an output, please click the ( ) icon within the
appropriate output button. To unmute the output, please click the icon a second time.
Note: The associated analog output will not be muted.
2. INPUT: Buttons for selecting the input to route to the selected output(s). Detail about the input names and signal information is also
displayed here. Clicking on the “edit” icon ( ) opens up the Edit Input window which allows for changing the input’s name.
Note: Blank spaces (“ ”) are not allowed in names.
3. EDIT OUTPUT: This window allows for changing a variety of settings related to
the video output.
■Output Name: To rename the output port, type the new name in the space
provided in the Edit window. Click the “Save” button to conrm the change.
Note: Blank spaces (“ ”) are not allowed in names.
■ OSD: This switch enables or disables the OSD custom text display for this output.
■ OSD Coordinate: This section denes the location of the OSD custom text. The
X value can be from 1 to 1920 and the Y value can be from 1 to 1080. Click the
“Save” button to conrm changes.
■ OSD Text: Each output can display up to 2 lines of customized OSD text. Enter
each line of text here. Click the “Save” button to conrm changes.
Note: Each line of text can have up to 64 characters.
■ OSD Text Size: Use the dropdown to select the preferred size for the OSD
custom text. Available sizes are: 1x, 2x, and 4x.
■OSD Text Color: Use the dropdown to select the preferred color for the OSD
custom text. Available colors are: black, white, red, green, blue, magenta, yellow,
cyan, and gray.
■OSD Background Color: Use the dropdown to select the preferred background
color for the OSD custom text. Available colors are: black, white, red, green, blue,
magenta, yellow, cyan, and gray.
■ OSD Background Color Transparent Level: Use the dropdown to select the
preferred transparency level of the OSD custom text’s background. The available
range is from Level 1 (fully opaque) to Level 8 (fully transparent).
ANEUVIDEO

13
WebGUI Control
4) PRESET SETTINGS: This matrix can store up to four
video routing presets. Presets can be utilized to store multiple
routing states in advance for rapid, hassle-free, recall.
■Preset Set: Once you have the matrix set the way you like,
you can click the “Preset Store” icon ( ) in the upper right
corner of the window and the Preset Store window will open.
Hovering the mouse over each button will display the current
routing stored within it. You may also rename each preset
by selecting the “Edit” icon ( ). Click the center of the
preferred preset’s button to store the current routing state in
that preset.
■Preset Recall: To load a previously stored preset, please click the “Preset Recall” icon ( ) and you will be presented with a choice
of the 4 available presets. Hovering the mouse over each button will display the routing currently stored within it. The preset will activate
immediately upon clicking the button.
EDID Settings Tab
This matrix provides the option of six standard EDIDs,
four sink sourced EDIDs and four user uploaded EDIDs
that can be assigned to each input port individually. The
names of the four user uploaded EDIDs can changed if
desired.
1. CUSTOMER EDID SETTINGS:
■ Save Name: To change the name of a Customer EDID,
type the new name in the space provided, then click on
the “Save Name” button.
■ Download: To save an existing user EDID to your
local PC please press the “Download” button next to
the EDID you would like to save. Depending on your
browser settings you will either be asked where to save
the downloaded le, or the le will be transferred to the
default download location on your PC.
■ Upload: To upload a new user EDID, please click the “Upload” button next to the Customer EDID Settings item you would like to
change. An EDID Upload window will appear, allowing you to locate and upload the preferred EDID le (*.bin format) from a local PC.
Once the correct le has been selected, please click the “Upload” button in the window, and the le will be transferred to the matrix.
2. SINK EDID DOWNLOAD: To save the EDID from one of the connected displays to your local PC, select the appropriate sink from
the dropdown list then press the “Download” button. Depending on your browser settings you will either be asked where to save the
downloaded le, or the le will be transferred to the default download location on your PC.
3. SET EDID INPUT CONTENT: Click
on the preferred input(s) to open the EDID
Source management window. Multiple
inputs can be selected at once, if desired.
Select the new EDID source to use and the
change will occur immediately.
Note: In most cases, assigning a new
EDID to an input will cause the aected
input to briey blink out while the source
adapts to the new information.
Note: In some cases it is possible for custom
or external EDIDs to cause compatibility
issues with certain sources. If this happens, it is recommended to switch to one of the 6 default EDIDs for maximum compatibility.
ANEUVIDEO
THIS MATRIX PROVIDES THE FOLLOWING 6 DEFAULT EDIDS:
UNIT’S DEFAULT EDIDS
FHD/2CH 1920x1080p@60Hz (4.95Gbps) & 8-bit color, LPCM 2.0
FHD/MCH 1920x1080p@60Hz (4.95Gbps) & 8-bit color, LPCM 7.1 & Bitstream
UHD/2CH 3840x2160p@30Hz (10.2Gbps) & Deep Color (8/10/12-bit), LPCM 2.0
UHD/MCH 3840x2160p@30Hz (10.2Gbps) & Deep Color (8/10/12-bit), LPCM 7.1 & Bitstream
UHD+/2CH 3840x2160p@60Hz (18Gbps) & Deep Color (8/10/12-bit), LPCM 2.0
UHD+/MCH 3840x2160p@60Hz (18Gbps) & Deep Color (8/10/12-bit), LPCM 7.1 & Bitstream

14
WebGUI Control
System Settings Tab
This page provides system conguration options
including turning the unit’s power on/o󰀨, changing the
network settings, resetting the system to factory defaults
and updating the rmware.
1. POWER: Press this switch to toggle the unit’s power
between ON and OFF (standby mode).
Note: While in standby mode the unit’s WebGUI, Telnet
and RS-232 controls are still active.
2. WEB USER SETTING: This section provides a
way to change the user name and password for the
Administrator account. Click on “Save” to conrm and
activate any changes made to these settings.
Note: The default username and password is “admin”.
3. WEB LOGIN TIMEOUT (MINUTE): Select the length of time to wait before logging the user out of the WebGUI due to inactivity. The
available range is from 5 to 60 minutes.
4. NETWORK: The unit’s IP mode may be switched between Static IP or DHCP. In Static IP mode the IP, netmask and gateway addresses
may be manually set. When in DHCP mode, the unit will attempt to connect to a local DHCP server and obtain IP, netmask and gateway
addresses automatically. Press “Save” after making any changes to the IP conguration or mode.
Note: The unit’s default IP address is 192.168.1.50. If the IP address is changed then the IP address required for WebGUI/Telnet access
will also change accordingly.
5. RESET TO DEFAULT: To reset the unit’s routing selections to the default settings, click the “Routing Reset” button. To reset the unit
to its factory default state press the “Fadefault” button. After the reset is complete, the unit will reboot automatically.
6. FIRMWARE UPGRADE: To update the unit’s rmware, click the “Choose File” button to open the le selection window and then
select the rmware update le (*.bin format) located on your local PC. After selecting the le, click the “Upgrade” button to begin the
rmware update process. After the upgrade is complete, the unit will reboot automatically.
ANEUVIDEO

15
ANEUVIDEO TELNET CONTROL
Telnet Control
Before attempting to use Telnet control, please ensure that both the unit and the PC/Laptop are connected to the same active networks.
To access the Command Line Interface (CLI)
In Windows XP Click Start > Run, type “cmd” in the search eld and press Enter.
In Windows 7 Click Start, type “cmd” in the search eld and press Enter.
In Mac OS X Click Go > Applications > Utilities > Terminal.
Once in the Command Line Interface (CLI) type “telnet” followed bythe IP address of the unit (and the port number if it is non-standard)
and then hit “Enter”. This will connect us to the unit we wish to control.
Note 1: If the IP address is changed then the IP address required for Telnet access will also change accordingly.
Note 2: The default IP address is 192.168.1.50.
Serial and Telnet Commands
COMMAND DESCRIPTION AND PARAMETERS
HELP 8Show the full command list.
? 8Show the full command list.
P0 8Turn the unit o󰀨 (stand-by mode).
P1 8Turn the unit on.
ST 8Show the unit’s current rmware version and routing status.
FADEFAULT 8Reset the unit to the factory defaults.
REBOOT 8Reboot the unit.
UPDATE 8Prepare the unit to update rmware via the USB port. After inserting a USB thumb drive containing a valid
rmware le (*.bin format) the update process will begin. After completion the unit will automatically reboot.
QUIT 8Log out from the current Telnet session.
SIPMODE N1 8
Set the IP address assignment mode.
Available values for N1:
STATIC [Static IP mode]
DHCP [DHCP mode]
SETIP N1 N2 N3 8
Set the IP address, netmask and gateway address to use when in Static IP mode.
N1 = X.X.X.X [X = 0 ~ 255, IP address]
N2 = X.X.X.X [X = 0 ~ 255, Netmask]
N3 = X.X.X.X [X = 0 ~ 255, Gateway address]
IPCONFIG 8Show the unit’s current IP conguration information.
ETH_FADEFAULT 8Reset the unit’s network settings to the factory defaults.
NAME N1 N2 8
Set a name for the specied preset.
N1 = 1~4 [Preset number]
N2 = {Preset name} [8 characters maximum]

16
ANEUVIDEO TELNET CONTROL
COMMAND DESCRIPTION AND PARAMETERS
N1N2 8
Route the specied input to one or more outputs.
N1 = A~D [Output port letter(s)]
N2 = 1~4 [Input port number]
Note: Multiple output letters may be assigned to N1 to route the same source to more than one output at
once.
For example: “ABD2” routes input 2 to outputs A, B, and D.
IN1 8
Route the specied input to all outputs.
N1 = 1~4 [Input port number]
Note: For example, “I3” routes input 3 to all outputs.
RS 8Reset the unit’s routing to the factory default.
STORE N1 8Save all current routing assignments to the specied preset.
N1 = 1~4 [Preset number]
SHOW N1 8List the routing assignments stored in the specied preset.
N1 = 1~4 [Preset number]
PRESET N1 8Activate the routing assignments saved in the specied preset.
N1 = 1~4 [Preset number]
EM N1 N2 8
Set the EDID to use on the specied input.
N1 = 1~4 [Input port number]
Available values for N2:
1 [FHD 2CH] 8 [Output B]
2 [FHD MCH] 9 [Output C]
3 [UHD 2CH] 10 [Output D]
4 [UHD MCH] 11 [User EDID 1]
5 [UHD+ 2CH] 12 [User EDID 2]
6 [UHD+ MCH] 13 [User EDID 3]
7 [Output A] 14 [User EDID 4]
USEREDID N1 N2 8
Set a name for the specied User EDID.
N1 = 1~4 [User EDID number]
N2 = {EDID name} [8 characters maximum]
BROADCAST N1 8
Enable or disable broadcast of command responses to control connections other than the current one.
Available values for N1:
ON [Enabled]
OFF [Disabled]
BROADCAST 8Show the current status of the broadcast setting.
CECOUT N1 N2 8
Send the specied command to the display connected to the specied HDMI output using CEC.
N1 = 1~4 [Output port number]
Available values for N2:
ON [Power o󰀨]
OFF [Power on]
VOL+ [Increase volume]
VOL- [Decrease volume]
MUTE [Mute audio]
OSDON N1 8Enable the OSD banner text on the specied output.
N1 = 1~4 [Output port number]
OSDOFF N1 8Disable the OSD banner text on the specied output.
N1 = 1~4 [Output port number]
OSDXY N1 N2 N3 8
Set the horizontal and vertical position of the upper left corner of the OSD banner text on the specied output.
N1 = 1~4 [Output port number]
N2 = 1~1920 [Horizontal position]
N3 = 1~1080 [Vertical position]

17
ANEUVIDEO TELNET CONTROL
COMMAND DESCRIPTION AND PARAMETERS
OSDSTR N1 N2 N3 8
Set the contents of the OSD banner text used on the specied
output.
N1 = 1~4 [Output port number]
N2 = 1~2 [Text line number]
N3 = {Text} [64 characters maximum]
OSDFSIZE N1 N2 8
Set the font size for the OSD banner on the specied output.
N1 = 1~4 [Output port number]
N2 = 1~3 [Font size]
OSDFCOLOR N1 N2 8
Set the color of the font used by the OSD banner on the specied output.
N1 = 1~4 [Output port number]
Available values for N2:
1 [Black] 6 [Magenta]
2 [White] 7 [Yellow]
3 [Red] 8 [Cyan]
4 [Green] 9 [Gray]
5 [Blue]
OSDBGCOLOR N1
N2 8
Set the color of the background of the OSD banner on the specied output.
N1 = 1~4 [Output port number]
Available values for N2:
1 [Black] 6 [Magenta]
2 [White] 7 [Yellow]
3 [Red] 8 [Cyan]
4 [Green] 9 [Gray]
5 [Blue]
OSDTS N1 N2 8
Set the transparency level for the background of the OSD banner on the specied output.
N1 = 1~4 [Output port number]
N2 = 1~8 [Transparency level]
OSDINFO N1 8
Enable or disable replacing the custom OSD banner text with system information.
Available values for N1:
ON [System info display enabled]
OFF [System info display disabled]
ROSDINFO 8Show the current status of the OSDINFO setting.
SDI_CUSTOM N1 8Set the discrete IR customer code to use.
N1 = 0000~FFFF [Discrete IR code in ASCII hex]
RDI_CUSTOM 8Show the current discrete IR customer code.
Note: Commands will not be executed unless followed by a carriage return. Commands are not case-sensitive.

18
CONNECTION DIAGRAM
CONNECTION DIAGRAM
ANEUVIDEO