A-Neuvideo ANI-88HDRH User manual

AUDIO / VIDEO MANUFACTURER
ANI-88HDRH
8X8 HDR 4K@60HZ HDMI 18G MATRIX SWITCHER
SCALER w/ USB POWER PORTS
INSTRUCTION MANUAL
A-NeuVideo.com
Frisco, Texas 75034
[phone]

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect Input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the Inputs with a signal level greater than that required to drive equipment to full Output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS
ANEUVIDEO
1
CONTENTS
INTRODUCTION & CONTENTS ..................................................1
FEATURES & SPECIFICATIONS .................................................2
OPERATION CONTROLS & FUNCTIONS .................................3
REMOTE CONTROL & IR CABLE PIN ASSIGNMENT ................5
LCD MENU TREE & RS-232 PROTOCOLS ...............................6
RS-232 & TELNET COMMANDS ..................................................8
TELNET CONTROL ....................................................................12
WEBGUI CONTROL ...................................................................13
CONNECTION DIAGRAM .........................................................18
SUPPORTED RESOLUTIONS ..................................................19
IR CABLE PIN ASSIGNMENT .....................................................20
INTRODUCTION
This 8x8 HDMI 6G (18G per channel) Matrix provides the ability to
connect up to (8) 6G HDMI sources and up to (8) 6G HDMI displays
and freely switch between them. This unit comes with full support for
6G resolutions up to and including 4K@60Hz (4:4:4, 8-bit) as well
as support for 48-bit Deep Color, HDR (High Dynamic Range), HD
audio and other features dened by the HDMI 2.0a specication.
With a comprehensive EDID management feature that includes
the ability to select between built in default EDID, EDID copied
from connected sink devices, as well as a congurable EDID, this
matrix can solve many inter-connectivity problems. This unit also
features (8) USB ports which supply up to 5V/1A power for use
with connected optical ber or AOC ber cable extenders. By using
these specialized cables your HDMI content can be extended much
further than would be possible with normal HDMI cables. The built
in OSD has the ability to display user editable general information
text. This unit provides an intuitive set of front panel controls with
an OSD as well as RS-232, Telnet, WebGUI and IR remote control
options. This product has a 3 year warranty.
PACKAGE CONTENTS
• ANI-88HDRH Matrix
• Remote control unit
• Rack ear set
• 24V / 6.25A Adaptor with power cord
• Users Guide
SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or
audio ampliers.
• The use of “Premium High Speed HDMI” cables is highly
recommended.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
w(8) to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2018. All Rights Reserved.
Version 1.2 JAN 2018
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATURES & SPECIFICATIONS
FEATURES
• HDMI 2.0a and DVI 1.0 compliant
• HDCP 1.4 and 2.2 compliant
• (8) 6G HDMI inputs can be matrixed to (8) 6G displays
• Supports HDTV resolutions up to 4K (3840x2160@24/25/30/50/60Hz & 4096x2160@24/25/30/50/60Hz) and VGA~WUXGA (RB)
• Supports a maximum data rate up to 18Gbps (6Gbps per channel) with deep color support up to 1080p, 48bit
• 4K/UHD capability @60Hz with 4:4:4 chroma subsampling
• Supports (6) internal EDIDs, (8) external EDIDs copied from connected devices and (4) user provided EDIDs
• (8) USB ports to supply 5V/1A power to optical ber and AOC ber extension cables
• OSD with user customizable information text
• Intuitive control interface including Telnet, WebGUI, OSD, IR remote and RS-232
• Easy rmware update via USB thumb drive in the eld
SPECIFICATIONS
• Video Bandwidth: 594MHz
• Input Ports: (8) HDMI
• Control Interfaces: IR In, RS-232, Service (USB), Control
• Output Ports: (8) HDMI, (8) USB port (5V/1A power supply)
• Supported Resolutions: 480i~4K@24/50/60Hz, 4K@50/60Hz VGA~WUXGA
• IR Frequency: 38kHz
• Baud Rate: 19200Bps
• Dimensions (WxHxD): 17.2 x 1.9 x 10.6 in (438x49x274mm) / 19 x 1.9 x 10.6 in (438x49x274mm) w/ Ear Mount Brackets
• Weight: 7.9 lb / 3600g
• Chassis Material: Metal
• Color: Black
• Power Supply: 24VDC/6.25A (US/EU standards, CE/FCC/UL certied)
As product improvements are continuous, specications are subject to change without notice.
ANEUVIDEO

3
OPERATION CONTROLS & FUNCTIONS
FRONT PANEL
qPOWER: Press this button to power the unit on (Green LED) or place it into stand-by mode (Red LED).
wIR RECEIVING WINDOW: Accepts IR signals from the included IR remote for control of this unit only.
eIN 1~8 & OUT A~H: Press the “OUT” keys (A~H) of the outputs you wish to route a source to (they will ash to indicate selection).
Next, press the “IN” key of the Input (1~8) you wish to route to the selected outputs. Finally, press “CONFIRM” to conrm your selection
and execute the routing change.
rCONFIRM: Press this button to conrm newly made input/output routing selections.
CANCEL: Press this button to cancel newly made input/output/preset routing selections before they have been conrmed.
t MENU: Press to enter the LCD menu or to back out from menu items.
yENTER: Press to conrm a selection within the LCD menu or to go deeper into a menu item.
u- / +: Press to move up and down or adjust selections within menus.
iALL: Press this button to select all outputs simultaneously for routing. Next, press the “IN” key of the input (1~4) you wish to route to
all outputs. Finally, press “CONFIRM” to conrm your selection and execute the routing change.
oPRESET: Press to enter the preset recall menu in the LCD window. Press the “+/-” buttons followed by the “ENTER” button to select
and activate the preferred preset.
aLOCK: Press to lock all button functions on the front panel. Press and hold for 3 seconds to release the lock function. The LCD will
display “LOCK” when the function is active.
sMUTE: The “MUTE” button functions as a blank audio/video source. To use it, follow the standard matrix routing instructions, but use
the “MUTE” button as the input to blank out the selected outputs. When a “MUTE” input is in use it will show up as “M” within the routing
display.
dLCD WINDOW: Displays the unit’s menu settings and information.
ANEUVIDEO

4
OPERATION CONTROLS & FUNCTIONS
Rear Panel
qHDMI IN 1~8: Connect to the HDMI source equipment such as media players, game consoles or set-top boxes.
wHDMI OUT A~H: Connect the HDMI outputs to devices such as HDMI TVs, monitors or ampliers for digital video and audio output.
Connect the optical outputs to powered speakers or ampliers for digital audio output using an appropriate optical cable. The audio from
each optical output will be the same as the HDMI output it is paired with.
eUSB POWER OUTPUT 1 ~ 8: Each USB port provides 5V/1A of power intended for use with HDMI over AOC (Active Optical Cables)
ber optic video extension cables.
rIR IN: Connect to the provided IR Extender to extend the IR control range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
tCONTROL: Connect directly or through a network switch, to your PC/laptop to control the unit via Telnet/WebGUI.
yRS-232: Connect directly to a PC, laptop or other serial control device to send RS-232 commands to control the unit.
uSERVICE: This slot is reserved for rmware update use only.
iDC 24V: Plug the 24V DC power adapter into the unit and connect it to an AC wall outlet for power.
ANEUVIDEO

5
Remote Control & IR Cable Pin Assignment
Remote Control
HEX CODES
CUSTOM CODE: 807F
POWER: 86 1 / A: 88
CANCEL: 84 2 / B: 8C
ENTER: 9E 3 / C: 90
MENU: D8 4 / D: 85
PLUS / IN: 9D 5 / E: 89
MINUS / OUT: 8F 6 / F: 8D
INFO: 8A 7 / G: 91
MUTE: 8E 8 / H: 95
PRESET: 92
ALL: C6
ANEUVIDEO
qPOWER: Press to power the unit on or place it into stand-by mode.
w1/A ~ 8/H: Press these keys to congure the video routing. Press the “OUT” key
followed by the key (A~H) of the outputs you wish to route a source to (they will ash
to indicate selection). Next, press the “IN” key followed by the input (1~8) you wish to
route to the selected outputs. Finally, press “ENTER” to conrm your selection and
execute the routing change.
eALL: Press this key to select all outputs simultaneously for routing. Next, press
the key of the input (1~4) you wish to route to all outputs. Finally, press “ENTER” to
conrm your selection and execute the routing change.
MUTE: Press this key to mute video output. Press the key of the input (1~4) you wish
to route then press mute key to mute video output.
INFO: Switches the information displayed on each output’s OSD between the user
customized text and the current video/Ethernet details.
PRESET: Press to enter the preset call menu in the LCD window. Press the “+/-”
buttons followed by the “ENTER” button to select and activate the preferred preset.
rA. MENU: Press to enter the LCD menu, or to back out from menu items.
B. ENTER: Press to conrm a selection within the LCD menu or to go deeper into
a menu item.
C. CANCEL: Press to cancel newly made input/output/preset routing selections
before they have been conrmed.
D. PLUS (+) / IN: Press “+/IN” to navigate up within menus or to begin the selection
of an input for routing.
E. MINUS (-) / OUT: Press “-/OUT” to navigate down within menus or to begin the
selection of outputs for routing.

6
LCD Menu Tree & RS-232 Protocols
LCD Menu Tree
1ST LEVEL 2ND LEVEL
EDID In1 / In2 / In3 / In 4 / In All
Preset Setup 1/2/3/4
Network Status Link (Valid) / Mode (Static/DHCP)/ IP/Mask / Gate/MAC
Network Setup Mode: (Static/DHCP)
Static: IP/Mask/Gate
Firmware Version
Firmware Update USB update
Factory Reset Factory reset
RS-232 Protocol
MATRIX REMOTE CONTROLLER
Pin Assignment Pin Assignment
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200bps
Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
ANEUVIDEO

7
RS-232 & Telnet Commands
RS-232 & Telnet Commands
COMMAND DESCRIPTION DESCRIPTION OF PARAMETER
?Print all available RS-232/Telnet
commands to the screen NONE
GET FW VER Print Firmware version to the screen NONE
COMMAND VER Print command version to the
screen NONE
GET MAC ADDR Print MAC address to the screen NONE
GET MODEL NAME Print Model Name to the screen NONE
GET MODEL TYPE N Print Model Name to the screen n: 1=matrix, 2=scaler, 3=splitter, 4=repeater
SET FACTORY DEFAULT Reset unit to factory default NONE
SET FACTORY IPCONFIG DEFAULT IP conguration was reset to factory
defaults (DHCP) NONE
SET FACTORY OUT ROUTE DEFAULT IP conguration was reset to factory
defaults (DHCP) NONE
SET POWER B Power unit ON/OFF b = ON, OFF
SET POWER N Power unit ON/OFF n = 0 - 1 (0-OFF, 1-ON)
SET POWER STANDBY Power unit Standby b = ON, OFF, STANDBY
GET POWER Print power unit ON/OFF/Standby to
the screen b = ON, OFF, STANDBY
SET UART N1 BAUDRATE N2 Set RS-232 baud rate n1 = 1,2,3…
n2 = 4800, 9600, 19200, 38400, 57600 or 115200
GET UART N BAUDRATE Print RS-232 baud rate to the
screen n = 4800, 9600, 19200, 38400, 57600 or 115200
SET IP MODE N n = 0-Static IP, 1-DHCP mode NONE
GET IP MODE Print IP mode status to the screen s = static, dhcp, force ip
GET IPCONFIG Print the current running IP cong to
the screen NONE
SET IPADDR N.N.N.N Print the IP address to the screen NONE
SET NETMASK N.N.N.N Set the NETMASK address n = 0~255
GET NETMASK Print the NETMASK to the screen NONE
SET GETEWAY N.N.N.N Set the GATEWAY address n = 0~255
GET GATEWAY Print the GATEWAY to the screen NONE
GET TELNET MAXIMUM USER N Print Telnet login status to the
screen n = 0,1,2,3,4…
SET WEBGUI USERNAME S Set WebGUI username {s} = name string
SET WEBGUI USERNAME Print WebGUI username to the
screen NONE
SET WEBGUI PASSWORD S Set WebGUI password {s} = password string
GET WEBGUI PASSWORD Print WebGUI password to the
screen NONE
SET WEBGUI LOGIN B Enable or disable WebGUI login b = ON, OFF (OFF-DISABLED, ON-ENABLED)
GET WEBGUI LOGIN Print WebGUI login status to the
screen NONE
ANEUVIDEO

8
RS-232 & Telnet Commands
COMMAND DESCRIPTION DESCRIPTION OF PARAMETER
SET TELNET USERNAME S Set Telnet username s = name string
GET TELNET USERNAME Print Telnet username to the screen NONE
GET TELNET USERNAME Print Telnet username to the screen NONE
SET TELNET PASSWORD S Set Telnet password s = password string
GET TELNET PASSWORD Print Telnet password to the screen NONE
SET TELNET PORT N Set Telnet port number n = 23,… (Telnet port number)
GET TELNET PORT N Set Telnet port number {s} = password string
GET HOSTENAME N Print Hostname to the screen {s} = name string
SET WEBGUI LOGIN TIMEOUT N Set WebGUI login timeout n = 1,2,3,4…Seconds
ROSDINFO Get OSD information status NONE
USBPWR USB Power ON/OFF USBPWR P1 P2
P1 = Output Port (1~4) / P2 = Action (ON/OFF)
SET IN N NAME S Name an input source n = 1,2,3…8
GET IN N NAME Print the input name to the screen n = 1,2,3…8
SET OUT X NAME S Name an output sync monitor x = a,b,c…h / s = name string name / size: 32 Byte
GET OUT X NAME Print the output name to the screen x = a,b,c …h
SET OUT X ROUTE N Set output routing x = a,b,c,d,e…h / n = 1,2,3,4,5…8
GET IN NAME LIST Print all input name to the screen NONE
GET OUT NAME LIST Print all output name to the screen NONE
SET OUT X 4K2K DOWNSCALE MODE N Cong output x 4K2K downscale
mode for sync monitor x = a,b,c…h / n = 0-passthrough, 1-auto, 2-1080p
GET OUT X HDCP 4K2K DOWNSCALE
MODE N
Print output x 4K2K downscale
mode to the screen x = a,b,c…h / n = 0-passthrough, 1-auto, 2-1080p
GET IN N1 HACTIVE N2 Print input H active to the screen n1 = 1,2,3…8 / n2 = 640, 800, 1024
GET IN N1 VACTIVE N2 Print input V active to the screen n1 = 1,2,3…8 / n2 = 480, 768, 600
GET IN N1 REFRESH RATE Print input refresh rate to the screen n1 = 1,2,3…8 / n2 = 5994, 6000, 7500, 8503
GET IN N1 INTERLACE Print input interlace to the screen n1 = 1,2,3…8 / n2 = 0-none interlace, 1-interlace
GET IN N1 SYNC STATUS Print input sync status to the screen n1 = 1,2,3…8 / n2 = 0-no sync, 1-sync active
GET IN N1 TIMING Print input n Timing n = 0,1,2,3,4,5…8
(0-native, 1-800x600, 2-1024x768,...)
SET IR IN CHANNEL N Set IR in channel information n = 0,1,2,3…15
GET IR IN CHANNEL N Get IR in channel information n = 0,1,2,3…15
SET IR IN CUSTOM CODE 0XH Set IR in custom code data: 0x0000~0x7fff
GET IR IN CUSTOM CODE Get IR in custom code data: 0x0000~0x7fff
SET FAN CONTROL MODEL N Print fan speed n: 0=always ON, 1=follow temperature
GET FAN CONTROL MODE Print fan speed n: 0=always ON, 1=follow temperature
GET FAN N1 SPEED Print fan speed n1 = 1,2 / n2 = 0,1,2,...
GET DEVICE TEMPERATURE N Print machine temperature n = 0,1,2,3…
ANEUVIDEO

9
RS-232 & Telnet Commands
COMMAND DESCRIPTION DESCRIPTION OF PARAMETER
GET USB X POWER SUPPLY B Set machine usb power supply
mode to ON/OFF x = a,b,c…h / b = ON, OFF
GET USB X POWER SUPPLY Print machine usb power supply
mode x = a,b,c…h / b = ON, OFF
SET OUT ROUTE XN-NN Routing command for all OUTPUT
Group xn-nn: a1 (a=1), b2 (b=2), c3 (c=3)…
SET ALL OUT ROUTE N Routing command for all OUTPUT n = 1,2,3,4,5…8
GET ALL OUT ROUTE Prints current routing status to the
screen NONE
SET KEYLOCK B Lock or unlock keypad b = ON, OFF (OFF-UNLOCKED, ON-LOCKED)
GET KEYLOCK Print Lock or Unlock keypad to the
screen NONE
SET CURRENT ROUTE TO PRESET N
Save the current routing state to a
preset (Video/Audio routing state
depends on different devices.
Please add other commands for key
features if required.)
n = 1,2,3,…8
SET ROUTE PRESET N Load a routing state from preset n = 1,2,3,…8
GET ROUTE PRESET N Print a routing state preset to the
screen n = 1,2,3,…8
SET ROUTE PRESET N NAME S Set a routing preset name n = 1,2,3,…8
GET ROUTE PRESET N NAME Get a routing preset name n = 1,2,3,…8
GET IN PORT NUMBER Print total input port number to the
screen NONE
GET IN PORT NUMBER Print total input port number to the
screen NONE
GET OUT PORT NUMBER Print total ouput port number to the
screen NONE
GET OUT X SYNC STATUS Print the output link status to the
screen x = a,b,c …h
SET OUT X MASK B MASK OUTPUT(S) x = a,b,c …h
b = ON, OFF (OFF=unmask, ON=mask)
GET OUT X MASK N MASK OUTPUT(S) x = a,b,c …h
SET OUT X OSD TRANSPARENCY
LEVEL N Set OUTPUT OSD transparency x = a,b,c,d,e…h / n = 1-8
GET OUT X OSD TRANSPARENCY
LEVEL N
Print output sync OSD transparency
to the screen x = a,b,c,d,e…h / n = 1-8
SET OUT X OSD B Set output [x] osd enable/disable x = a,b,c…h / b = ON, OFF
GET OUT X OSD Print output [x] osd enable/disable
to the screen x = a,b,c…h / b = ON, OFF
SET OUT X BANNER TEXT S Set output information banner (OSD
text) display text value x = a,b,c…h / s = string
GET OUT X BANNER TEXT Get output osd text (Information
banner) display text value x = a,b,c…h / s = string
SET OUT X BANNER FONT SIZE N Change OSD text size x = a,b,c…h / n = 1,2,3
GET OUT X BANNER FONT SIZE N Query OSD text size x = a,b,c…h / n = 1,2,3
SET OUT X BANNER FONT COLOR S Change OSD text color x = a,b,c…h / s = black, white, red, green, blue,
magenta, yellow, cyan, gray
ANEUVIDEO

10
RS-232 & Telnet Commands
COMMAND DESCRIPTION DESCRIPTION OF PARAMETER
GET OUT X BANNER FONT COLOR S Query OSD text color x = a,b,c…h / s = black, white, red, green, blue,
magenta, yellow, cyan, gray
GET OUT BANNER FONT COLOR LIST S Query OSD text color list value s = black, white, red, green, blue, magenta,
yellow, cyan, gray
SET OUT X OSD BACKGROUND COLOR S Change OSD text color x = a,b,c…h / s = black, blue, green, cyan, red,
magenta, yellow, white…
GET OUT X OSD BACKGROUND COLOR S Change OSD background color x = a,b,c…h / s = black, blue, green, cyan, red,
magenta, yellow, white…
GET OUT OSD BACKGROUND COLOR
LIST S
Query OSD background color list
value
s = black, blue, green, cyan, red, magenta,
yellow, white…
SET IN N1 EDID N2 EDID TABLE SELECT
n1 = 1,2,3,4… 8
n2 = 1,2,3… 22 (1-INT1, 2-INT2…,7-USER1,
8-USESR2…,15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
GET IN N1 EDID N2 Input EDID table query
n1 = 1,2,3,4… 8
n2 = 1,2,3… 22 (1-INT1, 2-INT2…,7-USER1,
8-USESR2…,15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
GET IN EDID LIST NN Input EDID table list query
nn = 1,2,3… 22 (1-INT1, 2-INT2…, 7-USER1,
8-USESR2…,15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
SET EDID N NAME S EDID TABLE SELECT n = 7,8,9,…14 (only USER EDID name can be
edited) / s = string / name size: 32 Byte
GET EDID N NAME S EDID TABLE SELECT n = 7,8,9,…14 (only USER EDID name can be
edited) / s = string / name size: 32 Byte
SET USER N EDID DATA H,H,H…… Upload EDID n = 1,2,3,4… 8 (1- USER1, 2-USER2…)
h = EDID data
GET USER N EDID DATA Download User n EDID n = 1,2,3,4…8 (1-INT1, 2-INT2…) / h = EDID data
GET SINK X EDID DATA Download SINK [x] EDID x = A,B,C…h / h = EDID data
GET IN N EDID DATA Download Input n EDID
n = 1,2,3… 8
h = EDID data (1-INT1, 2-INT2…,7-USER1,
8-USESR2…, 15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output
number of device.
GET ALL IN EDID LIST Print EDID list
n1 = 1,2,3,4… 8
n2 = 1,2,3… 22 (1-INT1, 2-INT2…,7-USER1,
8-USESR2…, 15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
GET INTERNAL N EDID DATA Download EDID n = 1,2,3,4…6 (1-INT1, 2- INT2…) / h = EDID data
SET ALL IN EDID MODE B Set EDID mode to “all” or “appoint” b = ON, OFF (all or appoint)
GET ALL IN EDID MODE B Print EDID mode to “all” or “appoint” b = ON, OFF (all or appoint)
ANEUVIDEO

11
RS-232 & Telnet Commands
COMMAND DESCRIPTION DESCRIPTION OF PARAMETER
SET ALL IN EDID N Set select EDID to all input
n = 1,2,3… 22 (1-INT1, 2-INT2…,7-USER1,
8-USESR2…,15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
GET ALL IN EDID N Print “all EDID mode” select EDID
n = 1,2,3… 22 (1-INT1, 2-INT2…,7-USER1,
8-USESR2…,15-Sink A, 16-Sink B)
Total User EDID number equal to Input source
number.
Total Sink EDID number equal to output number
of device.
SET IN N1 HDCP MODE N2 Set input [x] HDCP mode n1 = 1,2,3…8 / n2 = 0,1,2 (0-disable, 1-follow
source, 2-follow display)
GET IN N HDCP MODE N2 Print input [n] HDCP status to the
screen
n= 1,2,3…8 / n2 = 0,1,2 (0-disable, 1- follow
source, 2-follow display)
GET IN N HDCP STATUS Print input HDCP status to the
screen
n1 = 1,2,3…8 / n2 = 0,1,2,3 (0-OFF, 1-HDCP1.x,
2-HDCP2.2)
GET OUT X HDCP STATUS Print input HDCP status to the
screen
x = a,b,c…h / n2 = 0,1,2,3 (0-OFF, 1-HDCP1.x,
2-HDCP2.2, 3-HDCP1.x failed, 4-HDCP2.x failed)
GET OUT X HDCP STATUS Print input HDCP status to the
screen
x = a,b,c…h / n2 = 0,1,2,3 (0-OFF, 1-HDCP1.x,
2-HDCP2.2, 3-HDCP1.x failed, 4-HDCP2.x failed)
GET OUT X HDCP ABILITY N Print output [x] sink HDCP ability to
the screen
x = a,b,c…h / n2 = 0,1,2 (0-None HDCP,
1-HDCP1.x, 2-HDCP2.2)
GET IN X HDCP ABILITY N Print input n source HDCP ability to
the screen
n2 = 0,1,2,3 (0-None HDCP, 1-HDCP1.x,
2-HDCP2.2, 3-HDCP1.4+2.2)
SET PATTERN X MODE B Set pattern mode on, off x = a,b,c,d,e…h / b = on, off
GET PATTERN X MODE B Get pattern mode on, off x = a,b,c,d,e…h / b = on, off
SET PATTERN X TIMING N Set pattern output timing x = a,b,c…h (HDMI out, HDBT out, LR out… )
n = 1~41,401~435,501~506,..
GET PATTERN X TIMING N Get pattern output timing x = a,b,c…h (HDMI LR out… ) / n = out, HDBT
out, 1~41,401~435, 501~506,…
GET PATTERN TIMING LIST Get support pattern output timing list Please refer "timing code" table for detail timing
value denitions.
SET PATTERN X TYPE N Set pattern output type
x = a,b,c,d,e…h / n = 1: black, 2: white, 3: red, 4:
green, 5: blue, 6: magenta, 7: yellow, 8: cyan, 9:
gray
SET PATTERN X TYPE N Get pattern output type
x = a,b,c,d,e…h / n = 1: black, 2: white, 3: red, 4:
green, 5: blue, 6: magenta, 7: yellow, 8: cyan, 9:
gray
ANEUVIDEO

12
Telnet Control
Telnet Control
Before attempting to use the Telnet control, please ensure that both the Matrix (via the ‘LAN /CONTROL’ port) and the PC/Laptop are
connected to the same active networks. To access the Telnet control in Windows 7, click on the ‘Start’ menu and type “cmd” in the search
eld then press ENTER. Under Mac OS X, go to Go→Applications→Utilities→Terminal. See below for reference.
Once in the command line interface (CLI) type “Telnet”, then the IP address of the unit and “23”, then hit ENTER.
This will bring us into the unit which we wish to control. Type “help” to list the available commands.
NOTE: Commands will not be executed unless followed by a carriage return. Commands ARE case-sensitive. If the IP is changed then
the IP Address is required for Telnet access will also change accordingly.
ANEUVIDEO

13
WebGUI Control
WebGUI Control
Install the IP Discovery Tool:
1. Please obtain the Device Discovery software and save it in a directory where you can easily nd it.
NOTE: The unit’s default IP address is 192.168.1.50
2. Connect the unit and your PC/Laptop to the same active network and execute the Device Discovery software. Click on “Find Devices
on Network” and a list of devices connected to the local network will show up indicating their current IP address.
3. By clicking on one of the listed devices you will be presented with the network details of that particular device. If you choose, you can
alter the static IP network settings for the device or switch the unit into DHCP mode to automatically obtain proper network settings from a
local DHCP server. To switch to DHCP mode, please select DHCP from the IP mode drop-down, then click “Save” followed by “Reboot”.
4. Once you are satised with the network settings, you may use them to connect via Telnet or WebGUI. The network information window
provides a convenient link to launch the WebGUI directly.
• Login to the WebGUI:
1. By default, both the Username and Password are “admin” for the WebGUI. The
administrator password can be changed within the “System Settings” tab of the
WebGUI if desired.
2. The following function tabs will always display on left side of the WebGUI to aid
with navigation.
ANEUVIDEO

14
WebGUI Control
Video Switch
This page provides video routing settings, preset saving/
loading, and Pattern timing/color control settings.
• Video Routing: To begin assigning a new video route, please click
the button of the HDMI output you wish to send video to and then
click on the button of the preferred HDMI input port. If desired, you
may select more than one output prior to selecting the input. As you
select each button they will change their color to orange. The new
route will become active immediately after selecting the input port
and the routing information displayed on the buttons will change
accordingly.
• Output and Input Naming: All inputs and outputs can be renamed
as required. To rename the input and output ports please click the
“edit” icon ( ). Click the “Save” button to conrm the change.
NOTE: Blank spaces are not allowed in names.
• Output Video Mute: Each output can be individually muted (black
video, no audio). To mute an output, please turn on the icon.
• Pattern Timing: This Pattern timing tab provides multiple timing for
HDMI output, The supports timing are list below: 4K2K25~4K2K60
and 1080p60/1080p50 and 720p60/720p50.
• Pattern Color Control: The section allows for set the pattern color.
• DownScaling: The section allows for adjust from 4K2K to 1080
resolutions.
• OSD Text: The section allows the user to enable and disable the
OSD Text functions. If enabled, the OSD Text function allows text
entered in “OSD Text” to be displayed in the upper right corner of
the window. The text length is limited to 64 characters.
• OSD Text Settings: Each output can display (1) line of customized
OSD text. The text can be customized in content, background color,
size and position. Click the “edit” icon ( ) associated with each
output to modify these settings. Please click the “Save” button after
making changes to the positioning or content. All other changes
occur as soon as they are made.
ANEUVIDEO

15
WebGUI Control
• Preset Setting
This matrix can store up to (8) video routing presets. Presets can be
utilized to store multiple different routing states in advance for rapid,
hassle-free, recall.
• Store: Once you have the matrix set the way you like, youcan
click the “Preset Set” icon ( ) in the upper right corner of
the window and the Preset Set window will open. You may also
name the preset at this stage by selecting the “edit” icon ( ).
Click the main part of the Preset’s button to store the current
state into that preset.
• Recall: When you wish to load a previously stored preset, please
click the “Preset Recall” icon ( ) and you will be presented
with a choice of the available (8) presets. Hovering the mouse
over each button will display the preset routes stored within it.
The preset will load immediately upon selecting the preset.
ANEUVIDEO

16
WebGUI Control
EDID Settings
This matrix provides the option of (6) standard EDIDs,
(8) sink sourced EDIDs and (8) customer uploaded
EDIDs that can be assigned to each input port
individually. The names of the (8) customer uploaded
EDIDs can changed if desired.
• Customer EDID Settings: To upload a custom EDID,
please click the “Upload” button next to the Customer
EDID Settings item you would like to change. An
EDID Upload window will appear, allowing you to
locate and upload your preferred EDID le from the
le directory on your local PC. Once the correct le
has been selected, please click the “Upload” button
in the window, and the le will be transferred to the
matrix.
• Sink EDID Download: To save an existing custom
EDID to your local PC please press the “Download”
button next to the Customer EDID Settings item
you would like to save. Depending on your browser
settings you will either be asked where to save the
downloaded le or the le will be transferred to the
default download location on your PC.
• Set EDID Input Content: The Set EDID Input Content
section allows for the assignment of an EDID to each
individual input port, or to all inputs at once. Click
on an input to open the EDID Source management
window. Multiple inputs can be selected at once, if
desired. Select the new EDID source to use and the
change will occur immediately.
NOTE: This matrix comes with the following (6) default EDIDs:
1. FHD/2CH: 1080p@60Hz (148MHz), LPCM 2.0, 8-bit color.
2. FHD/MCH: 1080p@60Hz (148MHz), LPCM 7.1 & bitstream, 8-bit color.
3. 4K UHD/2CH: 3840x2160p@30Hz (297MHz), LPCM 2.0, Deep Color (8/10/12-bit)
4. 4K UHD / MCH: 3840x2160p@30Hz (297MHz), LPCM 7.1 & bitstream, Deep Color (8/10/12-bit).
5. 4K UHD+ / 2CH: 3840x2160p@60Hz (594MHz), LPCM 2.0, Deep Color (8/10/12-bit).
6. 4K UHD+ / MCH: 3840x2160p@60Hz (594MHz), LPCM 7.1 & bitstream, Deep Color (8/10/12-bit).
NOTE: In some rare cases it is possible for custom or external EDIDs to cause compatibility issues with certain sources. If this happens,
it is recommended to switch to one of the (6) default EDIDs for maximum compatibility.
ANEUVIDEO

17
WebGUI Control
Device Setting
• This page provides device settings options including
turning the USB power supply ON/OFF, changing the
IR Channel and IR discrete custom code, Displays
the unit’s temperature and current state of (2) external
fans including individual fan RPM. The fan control
default setting is always on.
User Config
• This tab provides User Conguration options including
changing the username and password for both of
Administrator and General user.
System Setting
• This page provides system conguration options
including turning the unit’s power ON/OFF, changing
the network settings, downloading/restoring saved
system congurations and updating the rmware.
Admin log out
Clicking the “Logout” tab will automatically log the user out of the WebGUI and return to login
page.
ANEUVIDEO

18
CONNECTION DIAGRAM
CONNECTION DIAGRAM
ANEUVIDEO