A-Neuvideo ANI-42HPIPX User manual

AUDIO / VIDEO MANUFACTURER
ANI-42HPIPX
UHD+ 4x2 HDMI Matrix with PiP
INSTRUCTION MANUAL
A-NeuVideo.com
Frisco, Texas 75036

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power o󰀨 and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS
ANEUVIDEO
1
CONTENTS
INTRODUCTION & CONTENTS .................................................1
FEATURES /APPLICATIONS / SYSTEM REQUIREMENTS ....2
SPECIFICATIONS / CABLE SPECIFICATIONS ........................3
OPERATION CONTROLS & FUNCTIONS ................................4
FRONTPANEL.....................................................................4
REAR PANEL ......................................................................5
RS-232 CONTROL / TELNET CONTROL ....................................6
OSD MENU ................................................................................14
WEBGUI CONTROL .................................................................23
CONNECTION DIAGRAM ........................................................29
VIDEO SPECIFICATIONS ........................................................30
AUDIO SPECIFICATIONS ........................................................31
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
The ANI-42HPIPX This 4x2 HDMI Matrix with PiP is a high
performance HDMI switch with integrated scaling and multi-
windowing technology which can connect up to (4) 4K UHD+ HDMI
sources to up to (2) 4K UHD+ HDMI displays and freely switch
between them. It is an ideal solution for monitoring or displaying
multiple sources simultaneously for use in control rooms, conference
rooms or classrooms. Video resolutions up to 4K@60Hz and LPCM
audio up to 7.1 channels at 192KHz are supported and this unit is
fully compatible with the HDCP 1.x and 2.2 standards.
Any of (4) di󰀨erent HDMI sources may be displayed individually,
full screen, with seamless switching in Matrix mode, or they can be
displayed using a variety of multi-window modes including standard
views like PiP (Picture in Picture) and PoP (Picture outside of
Picture) as well as fully customizable quad-window modes. Control
of input/window routing, position and sizing is easy using the front
panel controls with OSD menu as well as by WebGUI, RS-232, and
Telnet. This product has a 3 year warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and
make sure the following items are contained in the shipping carton:
• ANI-42HPIPX UHD+ 4x2 HDMI Matrix with PiP
• 24V/2.7A DC Power Adapter
• Rackmount Ears (Set of 2)
• Shockproof Feet (Set of 4)
• Users Guide
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
su󰀩cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2020. All Rights Reserved.
Version 1.0 FEB 2020
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATURES
FEATURES
• HDMI 2.0 and DVI 1.0 compliant (with the use of an HDMI-DVI adapter)
• HDCP 1.x and 2.2 compliant
• (4) HDMI inputs and (2) HDMI outputs
• Supports up to 4K UHD+ (18Gbps, 4K@50/60Hz 4:4:4, 8bit) video input and output
• Seamless switching (no loss of sync to display) when switching sources in Matrix mode
• Supports up to (4) simultaneous, freely scalable, windows in multiwindowing modes
• Supports the ability to store a multi-window arrangement as a preset that can be recalled later
• Independent audio source selection and routing in all modes
• Inputs 1 & 2 support pass-through of many audio formats including 8 channel LPCM, Bitstream, and HD Bitstream (Inputs 3 & 4 are
limited to 2 channel LPCM only)
• Each window can have a border with a selectable color
• Uploadable and freely positionable graphic logo support
• Intuitive and easy adjustment of window size, position and settings in multi-window modes via the WebGUI
• Per-input EDID management with internal or external EDID options
• Controllable via front panel buttons, WebGUI, Telnet, and RS-232
APPLICATIONS
• Entertainment Room & Home Theater
• Show Room & Demo Room
• Lecture Room & Hall Presentation
• Public Commercial Display
SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio ampliers.
ANEUVIDEO

3
SPECIFICATIONS
Specifications
• HDMI Bandwidth: 18Gbps
• Input Ports: (4) HDMI (Type-A)
• Output Ports: (2) HDMI (Type-A)
• Control Ports:
• RS-232 (3.5mm)
• IP Control (RJ-45)
• Service Port: USB 2.0 (Type A)
• Baud Rate: 19200
• Power Supply: 24V/2.7A DC (US/EU standards, CE/FCC/UL certied)
• ESD Protection (HBM):
• ±8kV (Air Discharge)
• ±4kV (Contact Discharge)
• Dimensions (WxHxD): 9.1 x 1 x 6.2 in (231.5x25x158mm) [Case Only] / 9.1 x 1 x 6.3 in (231.5x25x161mm) [All Inclusive]
• Weight: 2.1 lb / 968g
• Chassis Material: Metal (Steel)
• Chassis Color: Black
• Operating Temperature: 0˚C – 40˚C/32˚F – 104˚F
• Storage Temperature: -20˚C – 60˚C/-4˚F – 140˚F
• Relative Humidity: 20 – 90% RH (Non-condensing)
• Power Consumption: 15.3W
As product improvements are continuous, specications are subject to change without notice.
Cable Specifications
Cable Length
1080p 4K30 4K60
8bit 12bit (4:4:4) 8bit (4:4:4) 8bit
High Speed HDMI Cable
HDMI Input 49 ft / 15M 33 ft / 10M 16 ft / 5M 10 ft / 3M
HDMI Output 49 ft / 15M 33 ft / 10M 16 ft / 5M 10 ft / 3M
Bandwidth Category Examples:
• 1080p (FHD Video)
• Up to 1080p@60Hz, 12bit color
• Data rates lower than 5.3Gbps or below 225MHz TMDS clock
• 4K30 (4K UHD Video)
• 4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8bit color
• Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps
• 4K60 (4K UHD+ Video)
• 4K@50/60Hz (4:4:4, 8bit)
• 4K@50/60Hz (4:2:0, 10bit HDR)
• Data rates higher than 10.2Gbps
ANEUVIDEO

4
Operation controls & Functions
Front Panel
qSERVICE PORT: This port is reserved for rmware update and user EDID/logo upload use only.
wPOWER LED & BUTTON: Press this button to power the unit on (green LED) or place it into stand-by mode (red LED).
Note: Ethernet and RS-232 remain active when the unit is in stand-by mode.
eVIDEO MODE BUTTON: Press this button to sequentially switch the unit’s operational mode between Matrix, PiP, PoP, and Quad.
rOUT A~B/IN 1~4 LED ARRAY: In Matrix mode, these LED’s indicate the currently selected sources (IN 1~4) routed to each of the
(2) outputs (OUT A~B). When the unit is in a multi-windowing mode (PiP/PoP/Quad/Preset) all LEDs will be illuminated simultaneously.
Note: When source selection is active the associated output’s LED(s) will blink.
tOUT A/B BUTTONS: In Matrix mode, either of these buttons to activate/ deactivate discrete source selection for the associated output.
In multiwindowing modes (PiP/PoP/Quad/Preset) either button will activate/ deactivate sequential source selection for the (4) windows.
Note: These buttons only activate/deactivate the ability to change sources. Actual source selection is accomplished using the IN 1~4
buttons.
yIN 1/MENU BUTTON: When not in source selection mode, press to enter the OSD menu, or to back out from menu items. When
source selection is active, pressing this button will either select input 1 (Matrix mode) or sequentially switch through all (4) inputs for
window 1 (PiP/PoP/Quad/Preset modes).
Note: Pressing “MENU” and “+” together will reset the output resolution to XGA (1024x768@60Hz). Pressing “MENU” and “-”
together will reset the output resolution to 1080p@60Hz.
uIN 2/- (MINUS) BUTTON: When not in source selection mode, press to move down or adjust selections within OSD menus. When
source selection is active, pressing this button will either select input 2 (Matrix mode) or sequentially switch through all (4) inputs for
window 2 (PiP/PoP/Quad/Preset modes).
iIN 3/+ (PLUS) BUTTON: When not in source selection mode, press to move up or adjust selections within OSD menus. When source
selection is active, pressing this button will either select input 3 (Matrix mode) or sequentially switch through all (4) inputs for window 3
(PiP/PoP/Quad/Preset modes).
oIN 4/ENTER BUTTON: When not in source selection mode, press to conrm a selection within the OSD or to go deeper into a menu
item. When source selection is active, pressing this button will either select input 4 (Matrix mode) or sequentially switch through all (4)
inputs for window 4 (PiP/PoP/Quad/Preset modes).
ANEUVIDEO

5
Operation controls & Functions
BACK Panel
qHDMI IN 1~4 PORTS: Connect to HDMI source equipment such as media players, game consoles, or set-top boxes.
Note: Audio support on inputs 3~4 is limited to 2 channel LPCM.
wHDMI OUT A~B PORTS: Connect to HDMI TVs, monitors, or ampliers for digital video and audio output.
eCONTROL PORT: Connect directly, or through a network switch, to your PC/laptop to control the unit via Telnet/WebGUI.
rRS-232 PORT: Connect directly to a PC, laptop, or other serial control device with a 3.5mm adapter cable to send RS-232 commands
to control the unit.
tDC 24V PORT: Plug the 24V DC power adapter into this port and connect it to an AC wall outlet for power.
ANEUVIDEO

6
ANEUVIDEO RS-232 PINOUT / Telnet Control
RS-232 Pinout & Defaults
SERIAL PORT DEFAULT SETTINGS
BAUD RATE 19200
Data Bits 8
Parity Bits None
Stop Bits 1
Flow Control None
Telnet Control
Before attempting to use Telnet control, please ensure that both the unit and the PC are connected to the same active networks.
TO ACCESS THE COMMAND LINE INTERFACE (CLI)
Windows 7 Click START, type “cmd” in the search eld and press ENTER.
Windows 10 1. Open “Control Panel”.
2. Open “Programs and Features“.
3. Select the “Turn Windows features on or o󰀨 ” option.
4. Check the “Telnet Client” box.
5. Click “OK“. A box will appear that says “Windows Features” and “Searching for required
les “. When complete, the Telnet client should be installed in Windows.
Mac OS X Click Go > Applications > Utilities > Terminal.
Once in the Command Line Interface (CLI) type “telnet” followed by the IP address of the unit (and the port number if it is non-standard)
and then hit “Enter”. This will connect us to the unit we wish to control.
Note 1: If the IP address is changed then the IP address required for Telnet access will also change accordingly.
Note 2: The default IP address is 192.168.1.50.
3.5mm to DE-9
Adapter Cable

7
Serial & Telnet Commands
Serial & Telnet Commands
COMMAND DESCRIPTION
HELP 8Show the full command list.
HELP N1 8Show details about the specied command.
N1 = {Command}
? 8Show the full command list.
? N1 8Show details about the specied command.
N1 = {Command}
GET FW VER 8Show the unit’s current rmware version.
GET COMMAND VER 8Show the unit’s current command version.
GET MAC ADDR 8Show the unit’s MAC address.
GET MODEL NAME 8Show the unit’s model name.
GET MODEL TYPE 8Show the unit’s product type.
SET FEEDBACK BROADCAST N1 8Enable or disable the broadcast of console command feedback.
Available values for N1:
ON [Enabled]
OFF [Disabled]
GET FEEDBACK BROADCAST 8Show the current console command feedback broadcast state.
SET IP MODE N1 8Set the IP address assignment mode.
Available values for N1:
STATIC [Static IP mode]
DHCP [DHCP mode]
GET IP MODE 8Show the current IP address assignment mode.
GET IPCONFIG 8Show the unit’s current IP conguration information.
GET IPADDR 8Show the unit’s current IP address.
GET NETMASK 8Show the unit’s current netmask.
GET GATEWAY 8Show the unit’s current gateway address.
SET STATIC IPADDR N1 8Set the unit’s static IP address.
N1 = X.X.X.X [X = 0~255, IP address]
GET STATIC IPADDR 8Show the unit’s static IP address.
SET STATIC NETMASK N1 8Set the unit’s static IP address.
N1 = X.X.X.X [X = 0~255, Netmask]
GET STATIC NETMASK 8Show the unit’s static netmask.
SET STATIC GATEWAY N1 8Set the unit’s static IP address.
N1 = X.X.X.X [X = 0~255, Gateway address]
GET STATIC GATEWAY 8Show the unit’s static gateway address.
SET WEBGUI USERNAME N1 8Set the WebGUI login username.
N1 = {Username} [16 characters max]
GET WEBGUI USERNAME 8Show the current WebGUI login username.
SET WEBGUI PASSWORD N1 8Set the WebGUI login password.
N1 = {Password} [16 characters max]
GET WEBGUI PASSWORD 8Show the current WebGUI login password.
SET WEBGUI LOGIN TIMEOUT N1 8Set the WebGUI inactivity timeout value.
N1 = 0~240 [Minutes]
ANEUVIDEO

8
Serial & Telnet Commands
COMMAND DESCRIPTION
GET WEBGUI LOGIN TIMEOUT 8Show the current WebGUI inactivity timeout value.
SET TELNET LOGIN N1 8Enable or disable allowing Telnet logins.
Available values for N1:
ON [Enabled]
OFF [Disabled]
GET TELNET LOGIN 8Show the current state of Telnet login allowance.
SET TELNET USERNAME N1 8Set the Telnet login username.
N1 = {Username} [16 characters max]
GET TELNET USERNAME 8Show the current Telnet login username.
SET TELNET PASSWORD N1 8Set the Telnet login password.
N1 = {Password} [16 characters max]
GET TELNET PASSWORD 8Show the unit’s Telnet access port.
SET WINDOW LAYOUT MODE N1 8Set the window layout mode.
Available values for N1:
0 [Matrix mode]
1 [PiP mode]
2 [PoP mode]
3 [Quad mode]
4 [Preset 1]
5 [Preset 2]
6 [Preset 3]
7 [Preset 4]
GET WINDOW LAYOUT MODE 8Show the window current layout mode.
SET WINDOW N1 ROUTE N2 8Set the input to route to the specied window.
N1 = 1~4 [Window number]
N2 = 1~4 [Input port]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 ROUTE 8Show the input currently routed to the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET OUT N1 ROUTE N2 8Route the specied input to the specied output.
N1 = A~B [Output port]
N2 = 1~4 [Input port]
Note: Valid in matrix mode only.
GET OUT N1 ROUTE 8Show the current input routed to the specied output.
N1 = A~B [Output port]
Note: Valid in matrix mode only.
SET WINDOW N1 DISPLAY N2 8Enable or disable the specied window.
N1 = 1~4 [Window number]
Available values for N2:
ON [Enabled]
OFF [Disabled]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 DISPLAY 8Show the visibility status of the specied window,
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET WINDOW N1 HPOSITION N2 8Set the horizontal position of the specied window.
N1 = 1~4 [Window number]
N2 = 0~{Max res} [Horizontal size]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 HPOSITION 8Show the current horizontal position of the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
ANEUVIDEO

9
Serial & Telnet Commands
COMMAND DESCRIPTION
SET WINDOW N1 VPOSITION N2 8Set the vertical position of the specied window.
N1 = 1~4 [Window number]
N1 = 0~{Max res} [Vertical size]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 VPOSITION 8Show the current vertical position of the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET WINDOW N1 HSIZE N2 8Set the horizontal size of the specied window.
N1 = 1~4 [Window number]
N1 = 1~{Max res} [Horizontal size]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 HSIZE 8Show the current horizontal size of the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET WINDOW N1 VSIZE N2 8Set the vertical size of the specied window.
N1 = 1~4 [Window number]
N1 = 1~{Max res} [Vertical size]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 VSIZE 8Show the current vertical size of the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET WINDOW N1 PRIORITY N2 8Set the priority of the specied window.
N1 = 1~4 [Window number]
N1 = 1~4 [Priority]
Note: Valid in multi-windowing modes only.
GET WINDOW N1 PRIORITY 8Show the current priority of the specied window.
N1 = 1~4 [Window number]
Note: Valid in multi-windowing modes only.
SET WINDOW N1 ASPECT N2 8Set the aspect of the specied window.
N1 = 1~4 [Window number]
Available values for N2:
1 [Full]
2 [16:9]
3 [16:10]
4 [4:3]
5 [Best Fit]
6 [User]
GET WINDOW N1 ASPECT 8Show the current aspect of the specied window.
N1 = 1~4 [Window number]
SET WINDOW N1 MIRROR N2 8Set the mirror mode of the specied window.
N1 = 1~4 [Window number]
Available values for N2:
ON [Enabled]
OFF [Disabled]
GET WINDOW N1 MIRROR 8Show the current mirror mode of the specied window.
N1 = 1~4 [Window number]
SET WINDOW N1 BORDER N2 8Set the border mode of the specied window.
N1 = 1~4 [Window number]
Available values for N2:
ON [Enabled]
OFF [Disabled]
GET WINDOW N1 BORDER 8Show the current border mode of the specied window.
ANEUVIDEO

10
Serial & Telnet Commands
COMMAND DESCRIPTION
SET WINDOW N1 BORDER COLOR N2 8Set the border color of the specied window.
N1 = 1~4 [Window number]
Available values for N2:
1 [Black]
2 [Red]
3 [Green]
4 [Blue]
5 [Yellow]
6 [Magenta]
7 [Cyan]
8 [White]
9 [Dark Red]
10 [Dark Green]
11 [Dark Blue]
12 [Dark Yellow]
13 [Dark Magenta]
14 [Dark Cyan]
15 [Gray]
GET WINDOW N1 BORDER COLOR 8Show the current border color of the specied window.
N1 = 1~4 [Window number]
SET WINDOW N1 RESET 8Reset the settings of the specied window
N1 = 1~4 [Window number]
SET IN N1 CONTRAST N2 8Set the contrast level of the specied input.
N1 = 1~4 [Input port]
N2 = 0~100 [Contrast level]
GET IN N1 CONTRAST 8Show the current contrast level of the specied input.
N1 = 1~4 [Input port]
SET IN N1 BRIGHTNESS N2 8Set the brightness level of the specied input.
N1 = 1~4 [Input port]
N2 = 0~100 [Brightness level]
GET IN N1 BRIGHTNESS 8Show the current brightness level of the specied input.
N1 = 1~4 [Input port]
SET IN N1 SATURATION N2 8Set the saturation level of the specied input.
N1 = 1~4 [Input port]
N2 = 0~100 [Saturation level]
GET IN N1 SATURATION 8Show the current saturation level of the specied input.
N1 = 1~4 [Input port]
SET IN N1 HUE N2 8Set the hue value of the specied input.
N1 = 1~4 [Input port]
N2 = 0~100 [Hue value]
GET IN N1 HUE 8Show the current hue value of the specied input.
N1 = 1~4 [Input port]
SET IN N1 SHARPNESS H N2 8Set the horizontal sharpness level of the specied input.
N1 = 1~4 [Input port]
N2 = 0~20 [Horizontal sharpness level]
GET IN N1 SHARPNESS H 8Show the current horizontal sharpness level of the specied input.
N1 = 1~4 [Input port]
SET IN N1 SHARPNESS V N2 8Set the vertical sharpness level of the specied input.
N1 = 1~4 [Input port]
N2 = 0~20 [Vertical sharpness level]
GET IN N1 SHARPNESS V 8Show the current vertical sharpness level of the specied input.
N1 = 1~4 [Input port]
SET IN N1 PICTURE RESET 8Set the picture settings reset.
N1 = 1~4 [Input port]
SET AUDIO OUT N1 MUTE N2 8Enable or disable muting the specied audio output.
N1 = A~B [Output port]
Available values for N2:
ON [Mute]
OFF [Unmute]
ANEUVIDEO

11
Serial & Telnet Commands
COMMAND DESCRIPTION
SET AUDIO OUT N1 ROUTE N2 8Route the specied
audio source to the
specied audio output.
N1 = A~B [Output port]
Available values for N2:
1 [Input 1]
2 [Input 2]
3 [Input 3]
4 [Input 4]
5 [Window 1]
6 [Window 2]
7 [Window 3]
8 [Window 4]
GET AUDIO OUT N1 ROUTE 8Show the current audio source routed to the specied audio output.
N1 = A~B [Output port]
SET ALL IN EDID MODE N1 8Select the EDID management mode to use (All or Independent) for all inputs.
Available values for N1:
1 [All mode]
2 [Independent mode]
GET ALL IN EDID MODE 8Show the current EDID management mode used by all inputs.
SET ALL IN EDID N1 8Set the EDID to use
when the “All” EDID
mode is active.
Available values for N1:
1 [1080p60 2-Channel]
2 [4Kp30 2-Channel]
3 [4Kp60 2-Channel]
7 [User 1]
8 [User 2]
9 [User 3]
10 [User 4]
15 [Sink A]
16 [Sink B]
GET ALL IN EDID 8Show the current EDID used by the “All” EDID mode.
SET IN N1 EDID N2 8Set the EDID to use on
the specied input.
Available values for N1:
1 [1080p60 2-Channel]
2 [4Kp30 2-Channel]
3 [4Kp60 2-Channel]
7 [User 1]
8 [User 2]
9 [User 3]
10 [User 4]
15 [Sink A]
16 [Sink B]
GET IN N1 EDID 8Show the EDID currently being used on the specied input.
N1 = 1~4 [Input port]
SET USER EDID N1 UPDATE 8Upload a new EDID for use as the specied User EDID.
N1 = 1~4 [User EDID number]
SET IN N1 HDCP MODE N2 8Set the HDCP behavior of the specied input.
N1 = 1~4 [Input port]
Available values for N2:
0 [HDCP o󰀨]
1 [Refer to Source]
2 [Refer to Display]
GET IN N1 HDCP MODE 8Show the current HDCP behavior used by the specied input.
N1 = 1~4 [Input port]
SET OUT A TIMING N1 8Set the output resolution
to use for both outputs.
Available values for N1:
0 [640x480p59]
1 [480p60]
2 [576p50]
3 [800x600p60]
4 [848x480p60]
5 [1024x768p60]
6 [1280x720p50]
7 [1280x720p60]
8 [1280x768p60]
9 [1280x800p60]
10 [1280x960p60]
11 [1280x1024p60]
12 [1360x768p60]
13 [1366x768p60]
14 [1400x1050p60]
15 [1440x900p60]
16 [1600x900p60rb]
17 [1600x1200p60]
18 [1680x1050p60]
19 [1920x1080p24]
20 [1920x1080p25]
21 [1920x1080p30]
22 [1920x1080p50]
24 [1920x1200rb]
25 [2048x1152rb]
26 [3840x2160p24]
27 [3840x2160p25]
28 [3840x2160p30]
29 [4K p24 DCI]
30 [4K p25 DCI]
31 [4K p30 DCI]
32 [4K p50 DCI]
33 [4K p59 DCI]
34 [4K p60 DCI]
35 [3840x2160p50]
36 [3840x2160p59]
37 [3840x2160p60]
38 [Native OUT A]
39 [Native OUT B]
GET OUT A TIMING 8Show the current resolution used by both outputs.
ANEUVIDEO

12
Serial & Telnet Commands
COMMAND DESCRIPTION
SET OUT A OSD POSITION N1 8Set the OSD menu location.
Available values for N1:
0 [Top Left]
1 [Top Right]
2 [Bottom Right]
3 [Bottom Left]
GET OUT A OSD POSITION 8Show the current OSD menu location.
SET OUT A OSD TIMEOUT N1 8Set the OSD menu’s timeout value (in seconds).
Available values for N1:
OFF [Disabled]
5~60 [Timeout in seconds]
GET OUT A OSD TIMEOUT 8Show the current OSD menu’s timeout value.
SET OUT A OSD INFO DISPLAY N1 8Enable or disable the info OSD.
Available values for N1:
ON [Enabled]
OFF [Disabled]
GET OUT A OSD INFO DISPLAY 8Show the current info OSD state.
SET OUT A OSD INFO TIMEOUT N1 8Set the OSD info’s timeout value (in seconds).
Available values for N1:
OFF [Disabled]
5~60 [Timeout in seconds]
GET OUT A OSD INFO TIMEOUT 8Show the current OSD info’s timeout value.
SET OUT A OSD TRANSPARENCY N1 8Set the transparency level of the OSD.
N1 = 0~10 [Transparency level]
SET OUT A OSD BACKGROUND COLOR
N1 8
Set the color of the background of the OSD banner.
Available values for N1:
0 [Black]
1 [Gray]
2 [Blue]
GET OUT A OSD BACKGROUND COLOR 8
Show the current color of the background of the OSD banner on the specied
output.
SET OUT A OSD LOGO DISPLAY N1 8Enable or disable the graphical logo overlay.
Available values for N1:
ON [Enabled]
OFF [Disabled]
GET OUT A OSD LOGO DISPLAY 8Show the current state of the graphical logo overlay.
SET OUT A OSD LOGO HPOSITION N1 8Set the horizontal position of the graphical logo overlay.
N1 = 0~100 [Horizontal position]
GET OUT A OSD LOGO HPOSITION 8Show the current horizontal position of the graphical logo overlay.
SET OUT A OSD LOGO VPOSITION N1 8Set the vertical position of the graphical logo overlay.
N1 = 0~100 [Vertical position]
GET OUT A OSD LOGO VPOSITION 8Show the current vertical position of the graphical logo overlay.
SET OSD LOGO DEFAULT 8Resets the logo and installs a default test image.
SET OSD LOGO UPDATE 8Initiates the logo update process via USB.
SET SAVE PRESET N1 8Saves the current unit’s settings to the specied preset.
N1 = 1~4 [Preset number]
ANEUVIDEO

13
Serial & Telnet Commands
COMMAND DESCRIPTION
SET AUTO SYNC OFF N1 8Enable or disable the Auto Sync O󰀨
function and set the timeout length.
Available values for N1:
0 [Always on]
1 [5 seconds]
2 [10 seconds]
3 [15 seconds]
4 [30 seconds]
5 [1 minutes]
6 [1.5 minutes]
7 [2 minutes]
8 [2.5 minutes]
9 [3 minutes]
10 [5 minutes]
11 [10 minutes]
GET AUTO SYNC OFF 8Show the current Auto Sync O󰀨 settings.
SET FIRMWARE UPDATE 8Initiates the rmware update process via USB.
SET FACTORY USER EDID DEFAULT 8Restore the unit’s User EDIDs to their factory default settings.
SET FACTORY IPCONFIG DEFAULT 8Reset the unit’s network settings to the factory defaults.
SET FACTORY DEFAULT 8Restore the unit’s settings, except for User EDIDs, to the their factory default
settings.
Note: Commands will not be executed unless followed by a carriage return. Commands are NOT case-sensitive.6.6 WebGUI Control
ANEUVIDEO

14
OSD Menu
OSD Menu
All functions of this unit can be controlled by using the OSD (On Screen Display) which is activated
by pressing the MENU button on the front of the unit. Use the +(PLUS), −(MINUS), and ENTER
buttons to navigate the OSD menu. Press the MENU button to back out from any menu item and
then press it again to close the menu.
The individual functions of the OSD will be introduced in the followingsection. Items marked in
BOLD are the factory default settings.
1. Video Mode: Select the preferred operation mode of the unit.
Note: Selecting some modes will limit available features.
2. WIN 1/2/3/4 Source: Select the source for the specied window in multiwindowing
modes (PiP, PoP, Quad).
3. OUT A/B Source: Select the source for the specied HDMI output when in
Matrix mode.
ANEUVIDEO
MAIN MENU
Video Mode
Window Layout
Picture
Audio
Input EDID
HDCP Mode
Output Resolution
OSD Settings
Logo Settings
Ethernet
Preset
Setup
Information
VIDEO MODE
2ND LEVEL 3RD LEVEL
Video Mode Matrix
PiP
PoP
QUAD
Preset 1
Preset 2
Preset 3
Preset 4
PiP/PoP/Quad/Preset Mode
WIN 1 Source In 1~4 [1]
WIN 2 Source In 1~4 [2]
WIN 3 Source In 1~4 [3]
WIN 4 Source In 1~4 [4]
Matrix Mode
OUT A Source In 1~4 [1]
OUT B Source In 1~4 [2]

15
OSD Menu
1. Input Select: Select the input to modify.
Note: All settings are individually saved, per-input.
2. Aspect Ratio: Select a xed aspect ratio for the currently selected window.
Selecting the “Full” aspect ratio will stretch the source to ll the output, regardless
of original aspect. Selecting “Best Fit” will automatically set the ratio based on the
window’s current source resolution.
3. Mirror: Selecting “On” will ip the currently selected input horizontally.
4. Border On/O󰀨: Enables or disable the color border around the currently selected
input.
5. Border Color: Select the color to use for the border of the currently selected
input.
6. Window Reset: Reset the current input to its default settings.
ANEUVIDEO
WINDOW LAYOUT (MATRIX MODE)
2ND LEVEL 3RD LEVEL
Input Select In 1~4 [1]
Aspect Ratio FULL
16:9
16:10
4:3
Best Fit
Mirror NO
Yes
Border On/O󰀨 On
OFF
Border Color Black
Red
GREEN
Blue
Yellow
Magenta
Cyan
White
Dark Red
Dark Green
Dark Blue
Dark Yellow
Dark Magenta
Dark Cyan
Gray
Window Reset NO
Yes

16
OSD Menu
1. Window Select: Select the window to modify.
Note: All settings are individually saved, per-window/per-mode.
2. Window On/O󰀨: Enable or disable the currently selected window.
3. Position X/Y: Set the X and Y coordinate position of the upper left
corner of the currently selected window.
4. Size Width/Height: Set the horizontal and vertical size of the
currently selected window.
5. Priority: Select the layer priority of the currently selected window.
Priority 1 is at the front and priority 4 is at the back.
6. Aspect Ratio: Select a xed aspect ratio for the currently selected
window. The aspect ratio will be based on the window’s current
height.
Selecting the “Full” aspect ratio will return the window to the current
mode’s default size and shape for that window. Selecting “Best Fit”
will automatically set the ratio based on the window’s current source
resolution.
7. Mirror: Selecting “On” will ip the currently selected window
horizontally.
8. Border On/O󰀨: Enables or disable the color border around the
currently selected window.
9. Border Color: Select the color to use for the border of the currently
selected window.
10. Window Reset: Reset the current window to its default settings
based on the currently selected mode.
ANEUVIDEO
WINDOW LAYOUT (PIP/POP/QUAD/PRESET MODES)
2ND LEVEL 3RD LEVEL
Window Select Win 1~4 [1]
Window On/O󰀨 ON
O󰀨
Position X 0~Max H resolution
Position Y 0~Max V resolution
Size Width 1~Max H resolution
Size Height 1~Max V resolution
Priority 1~4 [4]
Aspect Ratio FULL
16:9
16:10
4:3
Best Fit
User
Mirror NO
Yes
Border On/O󰀨 On
OFF
Border Color Black
Red
GREEN
Blue
Yellow
Magenta
Cyan
White
Dark Red
Dark Green
Dark Blue
Dark Yellow
Dark Magenta
Dark Cyan
Gray
Window Reset NO
Yes

17
OSD Menu
1. Input Select: Select the input to modify.
2. Contrast: Set the overall contrast of the currently selected input.
3. Brightness: Set the overall brightness of the currently selected input.
4. Saturation: Set the overall saturation of the currently selected input.
5. Hue: Set the hue shift of the currently selected input.
6. Sharpness H/V: Set the amount of sharpness processing to apply to the currently
selected input.
7. Reset: Reset the current input to its default settings.
1. OUT A Source: Select the audio source to pair with video output A.
2. OUT A Mute: Enable or disable muting audio output A.
3. OUT B Source: Select the audio source to pair with video output B.
4. OUT B Mute: Enable or disable muting audio output B.
ANEUVIDEO
PICTURE
2ND LEVEL 3RD LEVEL
Input Select IN 1
In 2
In 3
In 4
Best Fit
Contrast 0~100 [75]
Brightness 0~100 [50]
Saturation 0~100 [50]
Hue 0~100 [50]
Sharpness H 0~10 [10]
Sharpness V 0~10 [10]
Reset NO
Yes
AUDIO (MATRIX MODE)
2ND LEVEL 3RD LEVEL
OUT A Source WINDOW
In 1
In 2
In 3
In 4
OUT A Mute On
OFF
OUT B Source WINDOW
In 1
In 2
In 3
In 4
OUT B Mute On
OFF

18
OSD Menu
1. OUT A Source: Select the audio source to pair with video output A.
2. OUT A Mute: Enable or disable muting audio output A.
3. OUT B Source: Select the audio source to pair with video output B.
4. OUT B Mute: Select the audio source to pair with video output B.
ANEUVIDEO
AUDIO (PIP/POP/QUAD/PRESET MODES)
2ND LEVEL 3RD LEVEL
OUT A Source WIN 1
Win 2
Win 3
Win 4
In 1
In 2
In 3
In 4
OUT A Mute On
OFF
OUT B Source WIN 1
Win 2
Win 3
Win 4
In 1
In 2
In 3
In 4
OUT B Mute On
OFF