A-Neuvideo ANI-527TX User manual
Transmitter
Receiver
AUDIO / VIDEO MANUFACTURER
ANI-527TX / RX
4K60Hz UHD+ HDR HDMI HDBaseT Transmitter/Receiver
w/ Bi-directional 24V PoC
A-NeuVideo.com
Frisco, Texas 75036
INSTRUCTION MANUAL
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your
equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,
water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean
dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken
so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper
AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may
impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used
in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all
servicing to qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting
cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship
the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY
INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
ANEUVIDEO
1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power
supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow
for sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for
any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means — electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise — without the express written permission and consent.
© Copyright 2020. All Rights Reserved.
Version 1.0 MAR 2020
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
ANEUVIDEO
2
TABLE OF CONTENTS
INTRODUCTION & CONTENTS .......................................................................................................2
FEATURES............................................................................................................................3
SPECIFICATIONS......................................................................................................................4
SYSTEM REQUIREMENTS / APPLICATIONS...................................................................................5
OPERATION CONTROLS & FUNCTIONS.......................................................................................6
REMOTE CONTROL / RS-232 PINOUT...........................................................................................5
CABLE PINOUTS / RS-232 BYPASS PINOUT / HDBASET™ FEATURES...................................10
CONNECTION DIAGRAM...............................................................................................................11
VIDEO SPECIFICATIONS...............................................................................................................12
AUDIO / CABLE SPECIFICATIONS.................................................................................................15
INTRODUCTION
The ANI-527RX & ANI527TX HDMI over HDBaseT™ Receiver & Transmitter are a great solution
for extending UHD video and audio as well as Ethernet and control via a single run of CAT5e/6/7
cable over distances up to 230 feet / 70 meters. This extender complies with the advanced HDCP
2.2 and HDMI 2.0 standards, as well as supporting the legacy HDCP 1.x and HDMI 1.x standards.
In addition, despite HDBaseT™’s 10.2Gbps bandwidth limitation, 4K UHD HDMI video sources,
up to and including 4K@60Hz (4:4:4, 8-bit) as well as 10/12-bit sources with HDR, are able to
be processed and extended by the use of AVLC (Adaptive Visually Lossless Compression) when
needed. Multiple data and control interfaces are also able to be extended, including IR, RS-232, and
LAN connections.
This unit supports bi-directional 24V PoC (Power over Cable) allowing the system to be completely
powered by, or provides power to, the compatible connected Receiver or Transmitter, allowing for
greater exibility within different installation scenarios. This product has a 3 year warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items
are contained in the shipping carton:
• ANI-527RX HDMI to HDBaseT™ Receiver w/ Bi-directional 24V PoC
• 3.5mm to IR Extender Cable
• Users Guide
&
• ANI-527TX HDMI to HDBaseT™ Transmitter w/ Bi-directional 24V PoC
• 24V/1.25A DC Power Adapter
• 2-pin Terminal Block
• 3.5mm to IR Blaster Cable
• Users Guide
3
FEATURES
• HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
• HDCP 1.x and HDCP 2.2 compliant
• Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input and output
• Supports Deep Color input and output up to 12-bit
• Supports 10-bit and 12-bit HDR (High Dynamic Range) input/output
• Supports CEC bypass
• HDBaseT™ feature support: HD Video and Audio, 24V PoC and Control (bi-directional IR/RS-232
pass-through)
• Receiver: HDBaseT™ input receives video, audio and data over a single CAT5e/6/7 cable and
can reach distances up to 70M/230ft at 1080p and 40M/131ft at 4K when using CAT6a/7
• Transmitter: HDBaseT™ output transmits video, audio and data over a single CAT5e/6/7 cable
and can reach distances up to 70M/230ft at 1080p and 40M/131ft at 4K when using CAT6a/7
•Integrated AVLC (Adaptive Visually Lossless Compression) activates when the bandwidth
requirements of the source are beyond 10.2Gbps (340MHz) allowing for support of sources up to
18Gbps (600MHz) with no loss of visual quality
• Supports pass-through of many audio formats including LPCM 2.0/5.1/7.1, Bitstream, and HD
Bitstream
• Bi-directional 24V PoC allows the unit to be powered by, or provide power to, a compatible
connected Transmitter
Note: The 24V PoC function is designed to power, or receive power from, compatible Transmitter
units only. Non-PoC Transmitters will need their own power supply. Other brands of Transmitter
may not be compatible.
Note: The 24V PoC function is designed to power, or receive power from, compatible Receiver
units only. Non-PoC Receivers will need their own power supply. Other brands of Receiver may
not be compatible.
4
SPECIFICATIONS
SPECIFICATIONS
• HDMI Bandwidth: 600MHz/18Gbps
• HDBaseT™ Bandwidth: 340MHz/10.2Gbps
• RX Input Port: HDBaseT™ (RJ-45)
• RX Output Port: HDMI
• RX Pass-through Ports:
• IR Extender (3.5mm)
• IR Blaster (3.5mm)
• RS-232 (DE-9)
• TX Input Port: HDMI
• TX Output Port: HDBaseT™ (RJ-45)
• TX Pass-through Ports:
• IR Extender (3.5mm)
• IR Blaster (3.5mm)
• RS-232 (DE-9)
• IR Frequency: 30 – 50kHz (30 – 60kHz under ideal conditions)
• Baud Rate: Up to 115200
• Power Supply: 24V/1.25A DC (US/EU standards, CE/FCC/UL certied)
• ESD Protection Human Body Model:
• ±8kV (Air Discharge)
• ±4kV (Contact Discharge)
• Dimensions (WxHxD): 4 x 1 x 4.2 in (102x25x107.5mm) [Case Only] / 4 x 1 x 4.5 in
(102x25x115mm) [All Inclusive]
• Weight: RX: 9.17 oz / 260g / TX: 8.61 oz / 244g
• Chassis Material: Metal (Steel)
• Chassis Color: Black
• Operating Temperature: 0˚C–40˚C/32˚F–104˚F
• Storage Temperature: -20˚C–60˚C/-4˚F–140˚F
• Relative Humidity: 20–90% RH (Non-condensing)
• Power Consumption: 14.5W (Tx+Rx)
As product improvements are continuous, specications are subject to change without notice.
5
SYSTEM REQUIREMENTS / APPLICATIONS
SYSTEM REQUIREMENTS
• HDMI receiving equipment such as an HDTV, monitor or audio amplier.
• An HDBaseT™ Transmitter equipped with AVLC and 24V PoC support is strongly recommended.
• An HDBaseT™ Receiver equipped with AVLC and 24V PoC support is strongly recommended.
• The use of “Premium High Speed” HDMI cables, and industry standard CAT6, CAT6a or
CAT7, is highly recommended.
APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
6
OPERATION CONTROLS & FUNCTIONS
Front Panel - RECEIVER
qISP PINHOLE: This button is reserved for factory use only.
wSTD/UPDATE SWITCH: This switch is reserved for factory use only.
Note: This should be left on the default setting of “STD” for normal operation.
eRS-232 PORT: Connect to a PC, laptop, or serial controllable device for the extension of RS-232
signals between both ends of the HDBaseT™ connection.
rPOWER LED: This LED will illuminate to indicate the unit is on and, receiving power.
SYNC LED: This LED will illuminate when a live input source is detected.
7
OPERATION CONTROLS & FUNCTIONS
back Panel - RECEIVER
qDC 24V TERMINAL BLOCK: Plug the 24V DC power adapter into this terminal block and connect
it to an AC wall outlet for power. (Optional)
Note: This connection is not required if the unit is receiving power via 24V PoC from the
Transmitter.
wIR BLASTER PORT: Connect to an IR Blaster to transmit IR signals from the other end of the
HDBaseT™ connection to devices within direct line-of-sight of the IR Blaster.
eIR EXTENDER PORT: Connect to the provided IR Extender to receive IR control signals and
extend them to devices connected to the other end of the HDBaseT™ connection. Ensure that the
remote being used is within direct line-of-sight of the IR Extender.
rCAT5E/6/7 IN PORT: Connect to a compatible HDBaseT™ Transmitter with a single CAT5e/6/7
cable for transmission of all data signals. 24V PoC can also be supplied to, or received from, a
connected compatible Transmitter.
Note: The 24V PoC function is designed to power, or receive power from, compatible Transmitter
units only. Non-PoC Transmitters will need their own power supply. Other brands of Transmitter
may not be compatible.
tHDMI OUT PORT: Connect to an HDMI TV, monitor, or amplier for digital video and audio output.
8
OPERATION CONTROLS & FUNCTIONS
Front Panel - TRANSMITTER
qISP PINHOLE: This button is reserved for factory use only.
wSTD/UPDATE SWITCH: This switch is reserved for factory use only.
Note: This should be left on the default setting of “STD” for normal operation.
eRS-232 PORT: Connect to a PC, laptop, or serial controllable device for the extension of RS-232
signals between both ends of the HDBaseT™ connection.
rPOWER LED: This LED will illuminate to indicate the unit is on and, receiving power.
SYNC LED: This LED will illuminate when a live input source is detected.
OPERATION CONTROLS & FUNCTIONS
back Panel - TRANSMITTER
qDC 24V TERMINAL BLOCK: Plug the 24V DC power adapter into this terminal block and connect
it to an AC wall outlet for power. (Optional)
Note: This connection is not required if the unit is receiving power via 24V PoC from the Receiver.
wIR BLASTER PORT: Connect to an IR Blaster to transmit IR signals from the other end of the
HDBaseT™ connection to devices within direct line-of-sight of the IR Blaster.
eIR EXTENDER PORT: Connect to the provided IR Extender to receive IR control signals and
extend them to devices connected to the other end of the HDBaseT™ connection. Ensure that the
remote being used is within direct line-of-sight of the IR Extender.
rCAT5E/6/7 IN PORT: Connect to a compatible HDBaseT™ Receiver with a single CAT5e/6/7
cable for transmission of all data signals. 24V PoC can also be supplied to, or received from, a
connected compatible Receiver.
Note: The 24V PoC function is designed to power, or receive power from, compatible Receiver
units only. Non-PoC Receivers will need their own power supply. Other brands of Receiver may
not be compatible.
tHDMI IN PORT: Connect to HDMI source equipment such as a media player, game console, or
set-top box. DVI sources are supported with the use of an HDMI to DVI adapter.
9
10
Cable Pinouts / RS-232 Bypass Pinout / HDBaseT™
Features
Cable Pinouts
RS-232 Bypass Pinout
HDBaseT™ Features
HDBaseT™Feature Set
Video & Audio Supported
IR Pass-through Supported
RS-232 Pass-through Supported
Accept power from Transmitter Supported
Send power to Transmitter Supported
LAN Pass-through Unsupported
RECEIVER TRANSMITTER
CONNECTION DIAGRAM
11
12
Video Specifications
Receiver Supported Resolutions (Hz) Input Output
HDBT HDMI
720x400p@70/85 ü ü
640x480p@60/72/75/85 ü ü
720x480i@60 ü ü
720x480p@60 ü ü
720x576i@50 ü ü
720x576p@50 ü ü
800x600p@56/60/72/75/85 ü ü
848x480p@60 ü ü
1024x768p@60/70/75/85 ü ü
1152x864p@75 ü ü
1280x720p@50/60 ü ü
1280x768p@60RB/60/75/85 ü ü
1280x800p@60RB/60/75/85 ü ü
1280x960p@60/85 ü ü
1280x1024p@60/75/85 ü ü
1360x768p@60 ü ü
1366x768p@60RB/60 ü ü
1400x1050p@60RB/60 ü ü
1440x900p@60RB/60/75 ü ü
1600x900p@60RB ü ü
1600x1200p@60 ü ü
1680x1050p@60RB/60 ü ü
1920x1080i@50/60 ü ü
1920x1080p@24/25/30 ü ü
1920x1200p@60RB ü ü
2560x1440p@60RB û û
2560x1600p@60RB û û
2048x1080p@24/25/30 ü ü
2048x1080p@50/60 ü ü
3840x2160p@24/25/30 ü ü
3840x2160p@50/60 (4:2:0) ü ü
Video Specifications
Receiver Supported Resolutions (Hz) Input Output
HDBT HDMI
3840x2160p@24/25/30, HDR10 AVLC AVLC ü
3840x2160p@50/60 (4:2:0), HDR10 AVLC AVLC ü
3840x2160p@50/60 AVLC AVLC ü
4096x2160p@24/25/30 ü ü
4096x2160p@50/60 (4:2:0) ü ü
4096x2160p@24/25/30, HDR10 û û
4096x2160p@50/60 (4:2:0), HDR10 û û
4096x2160p@50/60 û û
Transmitter Supported Resolutions (Hz) Input Output
HDMI HDBT
720x400p@70/85 ü ü
640x480p@60/72/75/85 ü ü
720x480i@60 ü ü
720x480p@60 ü ü
720x576i@50 ü ü
720x576p@50 ü ü
800x600p@56/60/72/75/85 ü ü
848x480p@60 ü ü
1024x768p@60/70/75/85 ü ü
1152x864p@75 ü ü
1280x720p@50/60 ü ü
1280x768p@60RB/60/75/85 ü ü
1280x800p@60RB/60/75/85 ü ü
1280x960p@60/85 ü ü
1280x1024p@60/75/85 ü ü
1360x768p@60 ü ü
1366x768p@60RB/60 ü ü
1400x1050p@60RB/60 ü ü
1440x900p@60RB/60/75 ü ü
1600x900p@60RB ü ü
13
Video Specifications
Transmitter Supported Resolutions (Hz) Input Output
HDMI HDBT
1600x1200p@60 ü ü
1680x1050p@60RB/60 ü ü
1920x1080i@50/60 ü ü
1920x1080p@24/25/30 ü ü
1920x1200p@60RB ü ü
2560x1440p@60RB û û
2560x1600p@60RB û û
2048x1080p@24/25/30 ü ü
2048x1080p@50/60 ü ü
3840x2160p@24/25/30 ü ü
3840x2160p@50/60 (4:2:0) ü ü
3840x2160p@24/25/30, HDR10 AVLC üAVLC
3840x2160p@50/60 (4:2:0), HDR10 AVLC üAVLC
3840x2160p@50/60 AVLC üAVLC
4096x2160p@24/25/30 ü ü
4096x2160p@50/60 (4:2:0) ü ü
4096x2160p@24/25/30, HDR10 û û
4096x2160p@50/60 (4:2:0), HDR10 û û
4096x2160p@50/60 û û
14
Audio / Cable Specifications
Audio Specifications
Digital Audio
HDMI INPUT/OUTPUT
LPCM
Maximum Channels 8 Channels
Sampling Rate (kHz) 32, 44.1, 48, 88.2, 96, 176.4, 192
BITSTREAM
Supported Formats Standard & High-Denition
Cable Specifications
CABLE LENGTH 1080p 4K30 4K60
8-bit 12-bit (4:4:4) 8-bit (4:4:4) 8-bit
High Speed HDMI Cable
HDMI Output 32 ft / 10 M 26 ft / 5 M 26 ft / 5 M 10 ft / 3 M
Ethernet Cable
CAT5e/6 197 ft / 60 M 16 ft / 35 M
CAT6a/7 230 ft / 70 M 131 ft / 40 M
• 1080p (FHD Video)
• Up to 1080p@60Hz, 12-bit color
• Data rates lower than 5.3Gbps or below 225MHz TMDS clock
• 4K30 (UHD Video)
• 4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit color
• 4K@50/60Hz (4:4:4, 8-bit) with AVLC active
• Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps
• 4K60 (UHD+ Video)
• 4K@50/60Hz (4:4:4, 8-bit), AVLC required over HDBaseT™
• 4K@50/60Hz (4:2:0, 10-bit HDR), AVLC required over HDBaseT™
• Data rates higher than 10.2Gbps
15
THIS PAGE IS INTENTIONALLY LEFT BLANK.
THIS PAGE IS INTENTIONALLY LEFT BLANK.
TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY,
THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to
these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address
set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You
are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty
pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you
and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are
licensed to you by A-NeuVideo, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use
only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo
does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein.
All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior
written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its ofces within the State of Texas, United States of America. A-NeuVideo makes no
representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect
thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or
typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO
DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES
NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE
CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS
REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS
AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND
CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID
TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
This manual suits for next models
1
Table of contents
Other A-Neuvideo Receiver manuals
