ABCwaters Fleck 5600SXT User manual

ABCwaters Fleck
5600SXT Water
Softener Install
Guide
Written by 602abcWATER

Step 1 – Conϐirm All Product Components
Open your packages and conirm that you
have received all the correct components. If
you are missing any of the listed items below,
please contact us at 602.222.9283.
Start Here
Package Contents
1 – Mineral tank preilled with resin
1 – Brine tank
1 – Fleck 5600sxt metered valve
1 – 1” Threaded Yoke
1 – Bypass
1 – Blue 602abcWATER bag (ABCwaters brand listings only)
1 – Small tube of silicone lubricant
1 – Sanitizer packet
1 – Water hardness test strip
* Not included but required – Salt, Telon Tape, ittings to connect softener
to your plumbing & ½” ID drain line. Please be sure to visit our website for
installation resources to assist you during your install.
Phone: [phone] – Monday thru Friday 7am to 4pm Arizona time.
Email: [e-mail]
Email: [e-mail]

Step 2 – Plan Your Water Softener Location
Plan where to position your water softener
system:
1. Position 5 ft. from power source to operate
2. Requires water drain for disposing of
water
3. Requires access to home’s main water line
Valve to Mineral Tank
Step 3 – Begin Assembly: Fleck Valve to Mineral
Tank
1. Apply silicone lube to small inner O-ring.
2. Attach top basket to the bottom of the Fleck
5600sxt valve. Insert large end of basket into groove
and turn clockwise into locking position.
3. Apply a thin layer of the provided silicon to large
‘O’-ring located outside of threads.
4. Connect the Fleck valve to the mineral tank. Be
sure to carefully line up the meter’s top basket to the
mineral tank’s distributor tube.
The mineral tank’s distributor tube should it inside
the top basket. Once aligned, screw on Fleck meter to
mineral tank’s threads. Hand tighten until tank starts
to spin. Do not hold tank and over tighten valve.

Step 4 – Connect Bypass to Fleck Meter
1. Apply silicone lube to the 2 ‘o’-rings on the
valve and make connection. We also recom-
mend applying silicone to the inside of the
female end on the bypass valve.
2. Position metal clips to clamp over the con-
nection point and fasten with screw. Because
the connection is O-ring sealed, it’s important
not to overtighten the screw. Overtightening
will cause damage to the plastic assembly.
Meter & Valve Assembly
Step 5 – Connect Yoke to Bypass
1. Apply silicone lube to the 2 ‘o’-rings on the
male connection on valve. Again, we also rec-
ommend applying silicone to the inside of the
female end of the yoke prior to connecting.
2. Position both metal clips to clamp over the
connection point and fasten screw. Remem-
ber not to over tighten screws.

Step 6 – Attach Drain Line to Fleck Meter
1. Wrap threaded connection point with 3-4
wraps of Telon tape. Install provided plastic
barbed itting.
2. Install drain line (not included) to barbed
itting (found on Fleck valve) with a stainless
hose clamp (not included). Drain line should
extend to a main drain to dispose of waste
water.
Attach Tank Lines
Step 7 – Connect Brine Line to Fleck Meter
1. Prep brine line prior to install using brass nut,
plastic Ferrule & brass tube insert.
2. Connect provided brass nut to the Fleck valve. Be
careful not to overtighten. Overtightening will cause
damage.
Step 8 – Connect Brine Well to Tank Side Wall
1. Locate predrilled hole in brine tank. Fas-
ten brine well to side wall of brine tank using
the white overlow elbow & plastic nut.
* This is preinstalled on Space Saver version.

Step 9 – Connect Brine Line to Safety Float
1. Insert 3/8” brine line through brine well
predrilled hole to connect to the safety loat.
Push brine line in push-connect itting on top
of safety loat.
Almost Finished
Step 10 – Connect Valve to Home Water Line
1. Connect your home’s input water line to
the Fleck meter through the port with ‘arrow’
pointing toward the meter.
2. Connect the remaining port with ‘arrow’
pointing away from meter to the home’s
incoming water line.
Step 11 – Connect Meter to Power Source
1. Plug in the Fleck 5600sxt digital meter to a power
receptacle. Your power source should be less than 5
feet in distance from the Fleck meter.
2. Turn bypass to ‘in service’ and let the tank ill
slowly. Turn on the closest cold water faucet to soft-
ener to bleed air from tank.

Step 1 – Conϐirm All Product Components
1. Add 3 bags of salt pellets or rock salt along
with 5 gallons of water to the brine tank.
* Add only 2 bags if using a SPACE SAVER
system.
Programming
Programming Your Hardness Water Softener
Step 1. Conduct hardness test with test strip provided.
Step 2. Press & Hold both ‘Up’ & ‘Down’ arrows together until screen
changes to DO (Day Override). This may take 5 seconds before change.
Step 3. Select # of days for DO. We suggest 14 days. Press ‘Cycle’ button
(icon of arrows in diamond pattern) after days are set.
Step 4. Set Regeneration Time (RT). We suggest setting to 2:00am. This is
the time that the system will regenerate. Press ‘Cycle’ button after setting
time.
Step 5. Set Hardness (H). Based on hardness test number. Press ‘Cycle’
button after set.
Step 6. Reserve Capacity (RC) should be set at 75 gallons per person in
household. Example: 2 people x 75 gal = 150 reserve capacity. Press ‘Cycle’
button to complete.

Contact 602abcWATER
Our company is managed by water professionals with over 25 years of com-
bined experience. Our goal is to provide you and your family with the best
equipment available in the industry, offer a support experience that is sec-
ond to none and have fair pricing that everyone can afford. If you have any
questions about which equipment is right for your home, or have installation
questions, give us a call.
We are located in Phoenix Arizona. We accept walk in orders from local res-
idents. We offer support via email, phone, text or video chat. Technical sup-
port is available Monday thru Friday between the hours of 7am to 4pm AZ
time.
23910 N. 19th Ave., Ste. 8
Phoenix, Arizona 85085
Web: www.602abcwater.com
Phone: [phone]
Email: [e-mail]
Text or Facetime: 602.321.0145
We want to thank you for choosing our business for your water treat-
ment needs. We would like to show our gratitude by offering a limited
time discount on your next purchase. Please call us within 30 days of
purchasing your water softener system and you will receive a 5% dis-
count on one of the following product lines listed below:
Drinking Water Filtration
Reverse Osmosis Systems
http://602abcwater.com/reverse-osmosis-systems/
Whole House Filtration
Carbon Uplow Systems
* 30 day time limit is based on our purchase invoice date.
Products That Compliment Water Softeners