ABES 480 User manual

A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
User Manual
Installation and maintenance instructions
ABE Bicycle- tand 480
with one-sided bike support
3-rack-system – wheel position low/low
4-rack-system – wheel position low/high
Version: 2021.V.2
After technical testing according to DIN 79008
, ABE Bicycle
-
tand
480 with one-sided bike support is recommended by the ADFC (Allge-
meiner Deutscher Fahrrad-Club e.V.).
Quality Label Test Number Q2103, 04/2021.

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 1
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Table of contents
Chapter Page
Manufacturer data ....................................................................................................................................................
Planning sketch ..........................................................................................................................................................
Technical data .............................................................................................................................................................
Dimensions ..............................................................................................................................................................
Material certifications .........................................................................................................................................
Main rack ............................................................................................................................................................ 3
Wheel rack ......................................................................................................................................................... 3
Chain lock and U-lock eyelet ....................................................................................................................... 3
Flanges plates ................................................................................................................................................... 3
Floor rails ............................................................................................................................................................ 3
Screws and small parts .................................................................................................................................. 3
Assembly ....................................................................................................................................................................... 4
Handling ....................................................................................................................................................................... 4
Parking the bike ..................................................................................................................................................... 4
Fastening an anti-theft device ......................................................................................................................... 4
Retrieving the bike ............................................................................................................................................... 4
Notes .............................................................................................................................................................................. 5
Weather protection .............................................................................................................................................. 5
Concerning the perceptibility of a vacant bicycle rack system ............................................................. 5
Stability and equilibrium .................................................................................................................................... 5
Cleaning ................................................................................................................................................................... 5
Maintenance, repairs and disposal .................................................................................................................. 6
Transport and storage.......................................................................................................................................... 6
Identification .......................................................................................................................................................... 6
Technical support ....................................................................................................................................................... 6
Appendices ................................................................................................................................................................... 7
Appendix 1.1 – Planning sketch 3-rack-system (low/low) ................................................................. 7
Appendix 1. – Planning sketch 4-rack-system (low/high) ............................................................... 8
Appendix .1 – Technical drawing 3-rack-system (low/low) ............................................................ 9
Appendix . – Technical drawing 4-rack-system (low/high) ........................................................ 10
Appendix .3 – Technical drawing single racks high and low ........................................................ 11
Appendix 3.1 – Assembly instructions 3-rack-system (low/low) ................................................... 1
Appendix 3. – Assembly instructions 4-rack-system (low/high) ................................................. 13

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Manufacturer data
ABES S.à r.l.
48, rue Gabriel Lippmann
L-6947 Niederanven
Contact:
Tel. [phone]
Fax [phone]
[email protected]
www.abes-online.com
VAT ID
: LU 16222668
Aut. d’Etablissement: 75207
R. C. . Luxembourg: B 48944
CEO: Rotger Barich
__________________________
Design: Christoph Marzi
Planning sketch

The space requirements for the setup, with recommendations relative to the depth
setting and the lateral spacing between two parking slots, as well as information on
the maneuvering area for the easy parking and retrieving of bikes, are the topics of
appendices 1.1 and 1.2.
Technical data
Dimensions
See appendices 2.1 and 2.2: Technical drawing with detailled measurements.
The dimensions give evidence of the bicycle stand system’s perceptibility in a vacant
state.
Material certifications
The bicycle stands are manufactured in Germany; their materials originate in the
European Economic Area.

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 3
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Main rack
Round tube (Ø 4 ,4 x mm), stainless steel 1.4301, polished (grain 40), noncor-
rosive. Tolerance according to ISO 11 7 D /T3.
ID No 5016660871000 , Heat Number 01/459673.
Wheel rack
Round tube (Ø 1 mm), stainless steel 1.4301, polished (grain 40), noncorrosive.
Tolerance according to ISO 11 7 D /T3
Chain lock and U-lock eyelet
Round tube (Ø 1 mm) stainless steel 1.4301, polished (grain 40), noncorrosive.
Tolerance according to ISO 11 7 D /T3
Flanges plates
Plate (50 x 1 0 x 8 mm), stainless steel 1.4301, polished (grain 40), noncorro-
sive. Tolerance according to ISO 11 7 D /T3
Floor rails
Trapezoidal rail (3 mm), stainless steel 1.4301, polished (grain 40), noncorrosive.
Tolerance according to ISO 11 7 D /T3
Screws and small parts
A list of all screws and small parts included in the delivery as well as their mate-
rials and quality can be found in appendices 3.1 and 3.2.

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 4
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Assembly

The bicycle st
and is designed to be set up on a flat concrete surface (C 5/30), or
any other underground with an equivalent bearing capacity, with a level value of
+/- 0 mm. A list of the components and the assembly instructions are summarized
under appendices 3.1 and 3.2. The disassembly happens in reverse order.
Handling
Parking the bike
Place the bike with its front wheel in a vacant slot.
The construction holds the bike by itself and is gentle
on the frame.
Fastening an anti-theft device
Connect the bike with a chain or U-lock to the pro-
vided inward looking eyelet, thus protecting it
against theft.
Retrieving the bike
Take off the chain or U-lock and remove the bike
from the slot.

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 5
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Notes
Weather protection
The bicycle stand is designed for outdoor use. No particular protection measures are re-
quired.
Concerning the perceptibility of a vacant bicycle rack
system
Visually impaired or blind persons can identify the bicycle stand system by touching it
with a cane. The front wheel rack functions as ground level crossbar (tactile bar). There
is no (tripping) hazard even though its lower edge is not set exactly 150 mm above
ground. Also, passers-by and users do not risk to hit their head as there is no component
at a height between 1.350 and .000 mm to pose any danger.
Stability and equilibrium
The bicycle stand offers secure positioning if assembled and mounted as indicated by the
guidelines in chapters Planning sketch, Technical data and Assembly.
The construction’s components have been given sufficiently large dimensions to guaran-
tee adequate theft prevention. Their preservation is subject to the condition of correct
use (see chapter Handling) and appropriate care (see chapter Cleaning). For the replace-
ment of damaged parts refer to chapter Repairs.
Cleaning
In spring and in autumn, the construction must be cleaned from major dirt, deposits, and
other impurities with water or a damp cloth. The use of corrosive or abrasive cleaners
can damage the surface permanently. Only cleaners specifically suited for stainless steel
may be used. The impact of dissolved dirt and cleaning agents on the environment
should also be considered.

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 6
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Maintenance, repairs and disposal
In summer and in winter, every screw joint has to be checked and, if need be, tightened
to ensure the stable connection between all the components.
The bicycle parker has a modular structure. Depending on the damage extend, affected
components can be removed and replaced. Spare parts can be requested and ordered
from the manufacturer. To contact the manufacturer, refer to chapter Manufacturer Da-
ta or Technical upport.
The disassembly happens in reverse order (see chapter Assembly).
The construction is made entirely of metallic components that can be disposed of at the
scrap metal collection and then recycled. Ask your local waste disposal company for the
location of collection sites near you.
Transport and storage
The construction is delivered disassembled. It can be stored and transported in a loose or
in an assembled state. Bicycle stands packed ex factory are not stackable. For the
product’s dimensions refer to chapter Dimensions.
Identification
Every bicycle stand bears a
facto-
ry label with the following in-
formation:
Technical support
 [e-mail]
 [phone]
 www.abes-online.com

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 7
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Appendices
Appendix 1.1 – Planning sketch 3-rack-system (low/low)
700
Rack spacing for low/ low bike support
1900
Length of storage area
1900
Length of storage area
1800
Length of Traffic area

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 8
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Appendix 1. – Planning sketch 4-rack-system (low/high)
500
Rack spacing for low/ high bike support
1900
Length of storage area
1900
Length of storage area
1800
Length of Traffic area

User Manual - ABES Bicycle-Stand 480
Installation and maintenance instructions
_________________________________________________________________________________________________________________
Page 9
A BES S.À R.L. 48, RUE GABRIEL LIPPMANN | L-6947 NIEDERANVEN | FON [phone] | FAX [phone]
OFFICE@ABE -ONLINE.COM | WWW.ABE -ONLINE.COM
Appendix .1 – Technical drawing 3-rack-system (low/low)