ABK i-Cooking User manual

INSTALLATION MANUAL
i-Cooking

EN 2 EN 3 Contents
Chapter 1
i-Cooking explanation 05
components 06
Chapter 2
installation instruction 08
2.1 adjusting the edge height
2.2 placing the housing
2.3 aligning the housing
2.4 fixing the gas volume indicator disk 09
2.5 placing the excenter disk
2.6 installing the burner clamps
2.7 fitting the burner installation disk
2.8 placing the pan supports 10
2.9 placing the burner components
2.10 positioning the indication on the gas volume indicator disk
2.11 connecting the appliance to gas and electricity

EN 2 EN 3 Contents
Chapter 1
i-Cooking explanation 05
components 06
Chapter 2
installation instruction 08
2.1 adjusting the edge height
2.2 placing the housing
2.3 aligning the housing
2.4 fixing the gas volume indicator disk 09
2.5 placing the excenter disk
2.6 installing the burner clamps
2.7 fitting the burner installation disk
2.8 placing the pan supports 10
2.9 placing the burner components
2.10 positioning the indication on the gas volume indicator disk
2.11 connecting the appliance to gas and electricity

EN 4 Introduction
i-Cooking explanation
1
435
6
i-Cooking is a personal cooking system. beautiful look, but is also very practical
You can determine the number, position for cleaning.
and type of burners, to your personal
preference. For example with more Within the current i-Cooking range, you
space between the burners, making it can choose from 15 predefined desigsn,
much more practical to use larger pans . but of course you also choose your own.
Use the guidelines at
i-Cooking offers four different burners, or consult our sales department.
for example the professional wok burner
with a very wide power range (0.18 to i-Cooking example
6.0 kW). i-Cooking can be integrated in 1 control knob with posistion indicator
almost any type of worktop, like 2 power burner | max 3.1kW
stainless steel, glass, concrete, stone 3 wok burner 2-rings | max 6.0kW
and composite. Please consult your 4 standard burner | max 1.6kW
supplier first. 5 simmer burner | max 1.0kW
6 black pan support power burner
Because of the patented construction, 7 black pan support wok burner
the burners stand directly and flush in 8 black pan support standard and
the worktop. This does not only create a simmer burner
www.i-cooking.eu
EN 5 Introduction
2
7 8

EN 4 Introduction
i-Cooking explanation
1
435
6
i-Cooking is a personal cooking system. beautiful look, but is also very practical
You can determine the number, position for cleaning.
and type of burners, to your personal
preference. For example with more Within the current i-Cooking range, you
space between the burners, making it can choose from 15 predefined desigsn,
much more practical to use larger pans . but of course you also choose your own.
Use the guidelines at
i-Cooking offers four different burners, or consult our sales department.
for example the professional wok burner
with a very wide power range (0.18 to i-Cooking example
6.0 kW). i-Cooking can be integrated in 1 control knob with posistion indicator
almost any type of worktop, like 2 power burner | max 3.1kW
stainless steel, glass, concrete, stone 3 wok burner 2-rings | max 6.0kW
and composite. Please consult your 4 standard burner | max 1.6kW
supplier first. 5 simmer burner | max 1.0kW
6 black pan support power burner
Because of the patented construction, 7 black pan support wok burner
the burners stand directly and flush in 8 black pan support standard and
the worktop. This does not only create a simmer burner
www.i-cooking.eu
EN 5 Introduction
2
7 8

Components
Wok burner
9 interior burner cover
10 pan support [black enamelled]
11 outer ring burner
12 gas distributor ring
13 cover ring air supply
14 burner mounting plate
15 worktop sealant
16 burner house
Power | standard | simmer burner
17 pan support [black enamelled]
18 burner cover
19 spiral burner
20 burner mounting plate
21 worktop sealant
22 burner house
Accessories [optional]
23 small pan adaptor-cross
24 XL wok pan support [for round wok]
EN 6 Components
23
24
9
10
11
12
13
14
17
18
19
20
15
16
21
22
fitting
fitting
EN 7 Components
Your i-Cooking purchase consists of: standard | power burner
Components kit
Per burner, a components kit is packed,
including the installation materials for
installing the burner and matching gas tap.
This kit also includes the separate burner
and gas tap components.
Wok burner
worktop-clips for housing [3x]
M4 bolts with fill ring for burner [3x]
burner-fastening disk
pan support
burner components [not on photo]
under-ring for knob, with bolts [2x]
gas tap eccenter disk, with screws [2x]
cover ring with gas knob position indication
gas knob
worktop-clips for housing [4x] Housing
M4 bolts for burner [3x]
burner-fastening disk
pan support
burner components [not on photo]
under-ring for knob, with bolts [2x]
gas tap eccenter disk, with screws [2x]
cover ring with gas knob position indication
gas knob
The housing has an aluminium top cooling
plate and an edge which is adjustable in
height [to be adjusted before fitting!]. In
the housing, all burner, gas tap and other
electrical and gas cooktop components
are pre-fitted.
1 Components

Components
Wok burner
9 interior burner cover
10 pan support [black enamelled]
11 outer ring burner
12 gas distributor ring
13 cover ring air supply
14 burner mounting plate
15 worktop sealant
16 burner house
Power | standard | simmer burner
17 pan support [black enamelled]
18 burner cover
19 spiral burner
20 burner mounting plate
21 worktop sealant
22 burner house
Accessories [optional]
23 small pan adaptor-cross
24 XL wok pan support [for round wok]
EN 6 Components
23
24
9
10
11
12
13
14
17
18
19
20
15
16
21
22
fitting
fitting
EN 7 Components
Your i-Cooking purchase consists of: standard | power burner
Components kit
Per burner, a components kit is packed,
including the installation materials for
installing the burner and matching gas tap.
This kit also includes the separate burner
and gas tap components.
Wok burner
worktop-clips for housing [3x]
M4 bolts with fill ring for burner [3x]
burner-fastening disk
pan support
burner components [not on photo]
under-ring for knob, with bolts [2x]
gas tap eccenter disk, with screws [2x]
cover ring with gas knob position indication
gas knob
worktop-clips for housing [4x] Housing
M4 bolts for burner [3x]
burner-fastening disk
pan support
burner components [not on photo]
under-ring for knob, with bolts [2x]
gas tap eccenter disk, with screws [2x]
cover ring with gas knob position indication
gas knob
The housing has an aluminium top cooling
plate and an edge which is adjustable in
height [to be adjusted before fitting!]. In
the housing, all burner, gas tap and other
electrical and gas cooktop components
are pre-fitted.
1 Components

EN 8 Installation instruction
Make sure that the underside of the 2.2 Place the housing of the cooktop under
worktop, where the cooktop will be fitted, the worktop and fit it with the 3 or 4 outer
is completely even and free from, dust, [temporarily] clamps/bolts, still loosened,
grease and glue remains. to the worktop.
Attention! The evenness is essential for
the cooling of the worktop by the
aluminum plate, which is fitted to the
worktop
2.1 First, the height of the adjustable edge
must be adjusted by yourself. Measure
the exact thickness of the worktop.
Use the mm indicators on the edge, to
make sure the thicknesses are exactly the
same on each position. Tighten the
screws firmly.
[The height of the edge and the worktop
will be 96mm].
2.3 Position the cooktop in such a position
that the burners and gas taps for the knobs
are in the centre of the cut outs.
2 Installation
!
EN 9 Installation instruction
2.4 Position and then fix the under-rings burners to the aluminum plate.
for the knobs, by screwing the M4 bolts Attention! Also remove the
into the aluminium plate. Depending on temporarily fixing clamps now.
the worktop thickness, the bolt can be tip: The clamps must be positioned over
shortened slightly, to prevent the bolt the worktop, as close to the edge of the
from getting in contact with the gas tap cut out as possible. If these are attached
components. Check and repeat this for to far/high over the edge, the burner-
each gas tap. fastening disk cannot be positioned
correctly and fixed 100% even anymore.
2.5 Place the steel eccenter disk over example Wok burner
the gas tap (extensions) to support the
gas tap and screw it firmly to the
worktop. Attention! Always use two
diagonally placed positions.
example Standard burner
2.7 Position the burner-fastening disk
above the burner house. If the plastic O-
ring [glued to the underside of the disk]
stands on the clamps, reposition the
2.6 Fix the remaining burner clamps. clamp. In case of the wok burner, the
Make sure all clamps are tightened bulb in the disk fits over the gas tube.
firmly to enable a maximum warmth Attention! For power, standard and
radiation from the worktop with the simmer burner, also use the fill rings>

EN 8 Installation instruction
Make sure that the underside of the 2.2 Place the housing of the cooktop under
worktop, where the cooktop will be fitted, the worktop and fit it with the 3 or 4 outer
is completely even and free from, dust, [temporarily] clamps/bolts, still loosened,
grease and glue remains. to the worktop.
Attention! The evenness is essential for
the cooling of the worktop by the
aluminum plate, which is fitted to the
worktop
2.1 First, the height of the adjustable edge
must be adjusted by yourself. Measure
the exact thickness of the worktop.
Use the mm indicators on the edge, to
make sure the thicknesses are exactly the
same on each position. Tighten the
screws firmly.
[The height of the edge and the worktop
will be 96mm].
2.3 Position the cooktop in such a position
that the burners and gas taps for the knobs
are in the centre of the cut outs.
2 Installation
!
EN 9 Installation instruction
2.4 Position and then fix the under-rings burners to the aluminum plate.
for the knobs, by screwing the M4 bolts Attention! Also remove the
into the aluminium plate. Depending on temporarily fixing clamps now.
the worktop thickness, the bolt can be tip: The clamps must be positioned over
shortened slightly, to prevent the bolt the worktop, as close to the edge of the
from getting in contact with the gas tap cut out as possible. If these are attached
components. Check and repeat this for to far/high over the edge, the burner-
each gas tap. fastening disk cannot be positioned
correctly and fixed 100% even anymore.
2.5 Place the steel eccenter disk over example Wok burner
the gas tap (extensions) to support the
gas tap and screw it firmly to the
worktop. Attention! Always use two
diagonally placed positions.
example Standard burner
2.7 Position the burner-fastening disk
above the burner house. If the plastic O-
ring [glued to the underside of the disk]
stands on the clamps, reposition the
2.6 Fix the remaining burner clamps. clamp. In case of the wok burner, the
Make sure all clamps are tightened bulb in the disk fits over the gas tube.
firmly to enable a maximum warmth Attention! For power, standard and
radiation from the worktop with the simmer burner, also use the fill rings>

EN 10 Installation instruction
between the bolts for a correct fitting
of the pan support.
tip: To achieve a proper sealing of the O-
ring to the worktop, the disk has a slight
tension in it self.
example Standard burner
2.10 Installation of the knobs and
indicator plate. Remove the paper from
the sticker under the indicator ring, press
it, in the correct position, on to the
under-ring and finally attach the knob.
Tip: First place and turn the knob in both
directions to verify the correct position of
the indicator ring.
2.8 Place the pan supports over the
disks. The heads of the bolts function as
cams for a correct fitting.
Tip: The fingers of the pan supports must
be alligned 100% vertically and
horizontally.
2.9 Place the remaining burner
components. Pay attention to the fitting 2.11 Connect the gas hose to the
pins and cut outs in the components. appliance and plug the power plug into
the power socket. Finally, check the
ignition of the burners and if the work in
highest and lowest capcity.
Notes
EN 11 Notes