Accel FX Power Source 10M User manual

INPUT:
Detachable 18V AC power adaptor
Country
Input AC Volt
North America
120V/60Hz
OUTPUTs:
All DC Outputs are regulated
Over current protection on each output
Output
DC Voltage
Current
1-7
9V
100mA
8
9V
500mA
9
12V
100mA
10
18V
100mA
Warranty
Limited 2 Year Warranty
This warranty covers any defects or malfunctions in your new Accel FX Power Source 10M
Power Supply. This a 2 year warranty for the original registered purchaser. Accel will fix or
replace any defective units with the first 2 years from the purchase date. Fixing or replacing
the unit will be at Accels discretion. Any problem that is caused by abuse, misuse, or an act of
God (such as a flood) are not covered. In order to be eligible for service under this warranty
you must return the warranty registration card attached below within 30 days of purchasing
the aid.
If something goes wrong with your Accel Power Source 6 Power Supply, email us at
[email protected]m
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
4
USER’S MANUAL
Table of Contents What’s Included
What’s Included………………………...1 (1) Accel FX Power Source 10M Power Supply
Introduction & General Information…..1 (1) User Manual
Warnings & Cautions………………… .2 (1) 18V adaptor
Component Description and (10) Negative Center Output Cables
Dimensional Drawing…………………. .3 (2) Reverse Polarity Cables
Power Supply Mounting Instructions….3
Specifications……………………………4
Warranty………………………………….4
Introduction:
Your Accel ”FX Power Source 10M” Ten Output Power Supply is designed with a high efficiency
transformer. Each output is fully regulated and filtered with over voltage protection.
Equipped with an on/off switch and our easy mount, mounting wings, adds an extra level of
convenience not found on similar power supplies.
The FX Power Source 10M , powers 9V, 12V & 18V effects pedals.
Outputs 1-7: 9V@ 100 mA powers the majority of the pedals on the market.
Output 8: 9V @ 500mA powers the 9V pedals and switchers that require more mA’s
Output 9: 12V @ 100mApowers most of your favorite 12V effects.
Output 10: 18V@ 100Ma powers most of your favorite 18V effects.
Read all warnings, cautions and operating instructions before using this product.
1

Read all Warnings and Cautions before operating your FX Power Source 10M
Power Supply
1. Keep these instructions –The safety and operating instructions should be retained for future reference.
2. All warnings, cautions and instructions should be adhered too for safe operation of your FX Power Source
10M Power Supply.
3. Follow all operating and use instructions for safe operation of this unit.
4. WARNING!!! The lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
5. WARNING!!! To reduce the risk of fire or electric shock, do not expose this power supply to rain or
Moisture. The unit should not be exposed to liquids of any kind. Any objects or containers filled with
liquids, such as drinks or beverages shall not be placed on top of the unit.
6. CAUTION!!! The exclamation with arrowhead symbol within an equilateral triangle is intended to alert the
users to the risk of damage to the FX Power Source 10M power supply if cautionary instructions are not
followed.
7. CAUTION!!! To prevent risk of overheating or damage to the FX Power Source 10M power supply. Do Not
Block any ventilation openings! The ventilation should not be impeded by covering the ventilation openings
with items such as, tape, fabric, Velcro or any potentially flammable material.
8. CAUTION!!! To prevent risk of overheating or damage to the FX Power Source 10M power supply. Mount per
the FX Power Source 10M Mounting Instructions!
9. Clean only with a dry cloth.
10. Do not install near any heat sources that produce heat.
11. Protect the power cord from being walked on or pinched. Especially near the plugs, convenience receptacles,
and at the point where they exit from the unit.
12. Follow all instructions and recommendations regarding attachments/accessories specified by the manufacturer.
13. Only use this unit as prescribed and specified by the manufacturer to power effects pedals.
14. Unplug the unit during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified personnel. Service is required when the power supply has been damaged in any
way –such as power supply cord or plugs damage; if any liquid or foreign objects have gotten inside the unit; if it
has been exposed to rain or moisture; has been dropped; or does not otherwise operate normally.
2
Component Description and Dimensional Drawing
1) Green AC power indicator 6) DC Output (12V @100mA)
2) Red DC power indicators 7) DC Output (18V @ 100mA)
3) AC 18V Input (18V adapter) 8) Power Supply ON / OFF Switch
4) DC Outputs (9V @100mA) 9) Power Supply Mounting Holes
5) DC Output (9V @ 500mA)
Power Supply Mounting
The FX Power Source 10M can mounted via the customer mounting holes
located on both easy mount wings. Hardware is not included, since pedal
board setups vary. 3