AccuEnergy Acuvim II series User manual

Acuvim II Series Power Meter
AXM-WEB-PUSH
User's Manual

Copyright © 2020 V1.36
This manual may not be altered or reproduced in whole or in part by any means without tzhe
expressed written consent of Accuenergy.

www.accuenergy.com
V: 1.36 Revised: June. 2020
1
The information contained in this document is believed to be accurate at the time of publica-
tion, however, Accuenergy assumes no responsibility for any errors which may appear here and
reserves the right to make changes without notice. Please ask the local representative for latest
product specifications before ordering.
Please read this manual carefully before installation, operation and maintenance of the
Acuvim II series meter. The following symbols in this manual are used to provide warning of
danger or risk during the installation and operation of the meters.
Electric Shock Symbol: Carries information about procedures which must be
followed to reduce the risk of electric shock and danger to personal health.
Safety Alert Symbol: Carries information about circumstances which if not
considered may result in injury or death.
Prior to maintenance and repair, the equipment must be de-energized and grounded. All main-
tenance work must be performed by quali󳆂ed, competent accredited professionals who have
received formal training and have experience with high voltage and current devices. Accuenergy
shall not be responsible or liable for any damages or injuries caused by improper meter installa-
tion and/or operation.

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
2
Contents
Chapter 1: Introduction to Ethernet ………………………………………6
Chapter 2: Functional Description of the Ethernet module …………6
Chapter 3: Appearance and Dimensions ………………………………7
Chapter 4: Installation Method ………………………………………… 8
Chapter 5: De󳆂nition of RJ45 …………………………………………… 9
Chapter 6: Initializing the Ethernet module ………………………… 10
Chapter 7: Cable …………………………………………………………… 19
Chapter 8: Connection Method ………………………………………… 19
8.1 Direct Ethernet Connection to a Computer ………………………………… 19
8.2 Connection to Router/Switch ………………………………………………… 24
Chapter 9: Description of Modbus-TCP Protocol…………………… 25
9.1 Protocol ……………………………………………………………………………25
a. Data Frame Format …………………………………………………………25
9.1.1 Modbus Application Header (MBA Header) Field ………………26
9.1.2 Function Field ……………………………………………………………26
9.1.3 Data Field …………………………………………………………………27
9.2 Format of Communication ………………………………………………………27
9.2.1 Explanation of frame ………………………………………………………27
9.2.2 Read Status of Relay (Function code 01) ………………………………29
9.2.3 Read Status of DI(Function Code 02) ………………………………31
9.2.4 Read Data(Function Code 03) …………………………………………32
9.2.5 Control Relay(Function Code05) ……………………………………34
9.2.6 Preset/Reset Multi-Register(Function Code 16) ……………………35
V: 1.36 Revised: June. 2020

www.accuenergy.com
3
Acuvim II Series - AXM WEB PUSH
Chapter 10 : Web Interface Readings and Parameter Settings …… 36
10.1 User Access Login …………………………………………………………………36
10.2 Dashboard ………………………………………………………………………37
10.3 Metering web page ……………………………………………………………38
10.3.1 Trend Log ………………………………………………………………39
10.3.2 Basic Metering ……………………………………………………………40
10.3.3 Power & Energy ………………………………………………………41
10.3.4 Min/Max ………………………………………………………………42
10.3.5 THD ………………………………………………………………………43
10.3.6 Harmonics ………………………………………………………………44
10.3.7 Phase Angle ………………………………………………………………45
10.3.8 Sequence ………………………………………………………………46
10.3.9 Data log ………………………………………………………………47
10.4 Status Menu ……………………………………………………………………48
10.4.1 Device Information ………………………………………………………48
10.4.2 Alarm Status ……………………………………………………………49
10.4.3 I/O …………………………………………………………………………49
10.4.4 SOE ………………………………………………………………………50
10.5 Web Page Settings ……………………………………………………………50
10.5.1 Meter Setting ……………………………………………………………51
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
4
Chapter 11 : Communications ………………………………………………… 52
11.1 WiFi Communication ………………………………………………………52
11.2 Network ………………………………………………………………………55
11.3 Emails …………………………………………………………………………56
11.4 Time & Date ………………………………………………………………………59
11.5 Datalog ……………………………………………………………………………61
11.5.1 Downloading the Data Logs ………………………………………64
11.6 HTTP/FTP Post ……………………………………………………………………64
11.6.1 HTTP Post …………………………………………………………………66
11.6.2 FTP Post …………………………………………………………………68
11.7 AcuCloud Post …………………………………………………………………70
11.8 SNMP ……………………………………………………………………………71
11.9 DNP ……………………………………………………………………………73
11.10 Remote Access ………………………………………………………………77
11.11 Import/Export Con󳆂guration ………………………………………………79
11.11.1 Export Con󳆂guration ………………………………………………80
11.11.2 Import Con󳆂guration ………………………………………………80
Chapter 12 : Management ………………………………………………… 81
12.1 Parameter Reset ……………………………………………………………81
12.2 Reboot Meter & Communications Module ……………………81
12.3 Change Password ………………………………………………………………82
12.4 Diagnostic File …………………………………………………………………82
V: 1.36 Revised: June. 2020

www.accuenergy.com
5
Acuvim II Series - AXM WEB PUSH
Chapter 13 : Network Diagnostic ……………………………………………… 83
13.1 Network Status ………………………………………………………………83
13.2 Host Lookup …………………………………………………………………84
13.3 Connection Test …………………………………………………………………85
Chapter 14 : Firmware Update …………………………………………………… 86
14.1 Manual Firmware Update …………………………………………………86
14.2 Remote Firmware Update ………………………………………………
88
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
6
1. Introduction to Ethernet
Ethernet was originally developed by Xerox and then further developed by DEC and Intel. This
networking technology uses Carrier Sense Multiple Access with Collision Detection (CDSM/CD)
protocol and provides transmission speeds up to 100Mbps.
Ethernet is a not a network but more of a standard. It is the most current communication
standard Local Area Network(LAN). This standard de󳆂nes the type of cable that is used and the
method of Signal Processing.
2. Functional Description of the Ethernet module
The AXM-WEB-PUSH module supports the Modbus-TCP protocol. When connected to the
Acuvim II series meter, it is a slave device that can only respond to queries. The default value
for the Modbus Port is 502. The user de󳆂ned range is 2000~5999.
This module supports the SMTP protocol, which allows the user to send emails based on a
speci󳆂c time interval or when a triggered event occurs. It can send mail from encrypted servers
and servers that use di󳆁erent SMTP ports.
The AXM-WEB-PUSH supports the HTTPS protocol, it is used as an HTTPS server where the
default value of the protocol port is 443. Using the HTTPS protocol, the AXM-WEB-PUSH can
send post requests to both HTTP and HTTPS servers.
The following are all the protocols supported by the AXM-WEB-PUSH module:
• Modbus TCP
•SNMP
•DNP 3.0
•SMTP
•SNTP
•HTTP/HTTPs
•FTP
•sFTP
V: 1.36 Revised: June. 2020

www.accuenergy.com
7
Acuvim II Series - AXM WEB PUSH
90mm
(Side View)
22mm
55.6mm
(Bottom View)
(Top View)
3. Appearance and Dimensions
V: 1.36 Revised: June. 2020

www.accuenergy.com
8
Acuvim II Series - AXM WEB PUSH
4. Installation Method
The AXM-WEB-PUSH module is linked to the Acuvim II series meter by a communication plug.
Other extended modules such as the IO modules can be linked to the Acuvim II series meter
through the AXM-WEB-PUSH.
1) Remove cover from the back of the Acuvim II series meter which will expose the socket.
2) Insert the installation clips to the grooves in the Acuvim II series meter and then press the
AXM-WEB-PUSH module lightly to establish a linking between meter and module.
3) Tighten the installation screws.
NOTE: Installation with power to the meter is forbidden.
NOTE: If using extended I/O modules with AXM-WEB-PUSH module, ensure that the WEB-PUSH
module is attached to the meter 󳆂rst followed by the I/O modules. If the WEB-PUSH module is
not connected 󳆂rst it will not be able to communicate with the Acuvim II meter.
V: 1.36 Revised: June. 2020

www.accuenergy.com
9
Acuvim II Series - AXM WEB PUSH
5. De󳆂nition of RJ45
The AXM-WEB-PUSH uses a standard RJ45 connector to access the Ethernet network. The me-
chanical and electrical characteristics of the connector are consistent with the requirements of
IEC 603-7.
(Top View)
Script ID Content
1TX+ Tranceive Data+
2TX- Tranceive Data-
3RX+ Receive Data+
4n/c Not connected
5n/c Not connected
6RX- Receive Data-
7n/c Not connected
8n/c Not connected
LED_L (Yellow): Displays the speed status. When the LED is on it indicates 100Mpbs, whiles an
o󳆁 LED represents a speed of 10Mbps.
LED_R (Green): Displays the link and activity status. When the LED is on it indicates that the
link status. When the LED is 󳆃ashing it indicates that there is activity.
LED L LED R
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
10
6. Initializing the Ethernet module
The default settings in the Acuvim II series meter are as followed:
• DHCP: Manual
• IP Address: 192.168.1.254
• Subnet Mask: 255.255.255.0
• Gateway: 192.168.1.1
• Primary DNS Server: 8.8.8.8
• Secondary DNS Server: 8.8.4.4
• Modbus Port: 502
• HTTP Port: 80
This information can be found by using the buttons from the meter display. The following is how
to con󳆂gure the Ethernet module settings from the display:
• Press the H and V/A buttons simultaneously on the Acuvim II series for about a second
and release. The screen will go blank and Meter will be 󳆃ashing.
V: 1.36 Revised: June. 2020

www.accuenergy.com
11
Acuvim II Series - AXM WEB PUSH
• Press the Por Ebutton to move the cursor to Setting and then press V/A to enter the
parameter setting mode. The device address page is the 󳆂rst page of the 'Setting' mode. It
will show the Modbus address of the meter for a second before prompting for the pass-
word of the device.
• Press V/A button to con󳆂rm password and enter the parameter setting page.
• Press the P or E button to move the cursor to NET and press the V/A button to enter the
Ethernet module settings.
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
12
•The first page of the NET Settings will be the N01 DHCP page. By default this is config-
ured to Manual. Configuring this setting to
Auto will allow the network to assign the
meter an IP address, whiles Manual will allow the user to configure the IP address.
• Press the V/A button to enter edit mode. Press P or E to change the setting and press
V/A to confirm the setting.
NOTE: If the DHCP is selected as Auto, the Ethernet module needs to be rebooted before it can
be assigned with the new IP address.
V: 1.36 Revised: June. 2020

www.accuenergy.com
13
Acuvim II Series - AXM WEB PUSH
• Press P to move to the next screen which is N02 IP address, this is the IP address of the
meter and will be the IP address to access the web interface of the module. Users can
con󳆂gured the IP address if the DHCP is con󳆂gured to Manual.
• Press V/A to con󳆂gure the IP address, the cursor of the 󳆂rst digit will begin to 󳆃ash. Press
the Hbutton to scroll through the digits, press the Por E to change the value of the 󳆃ash-
ing cursor. Once the IP is con󳆂gured users can press V/A to con󳆂rm the setting.
• Press Pto move to the N03 Subnet Mask page. This is the subnet mask setting of the
meter. If the DHCP is set for Manual users must manually con󳆂gure subnet mask.
• To con󳆂gure the submask press V/A to enter edit mode, the cursor of the 󳆂rst digit will
begin to 󳆃ash.
• Press the H button to scroll to the next digit and press P or E to change the value of the
digit. Once the sub mask has the correct address press V/A to con󳆂rm setting.
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
14
• Press Pto move to the N04 Gateway page. This is the meters gateway setting, and will
need to be configured if the DHCP is set to Manual.
•To configure the gateway press
V/A to enter edit mode, the cursor will begin to flash on
the first digit.
• Press the H button to scroll through the digits, and then press P or E to change the
value of the digit. Once the gateway is configured press V/A to confirm the setting.
V: 1.36 Revised: June. 2020

www.accuenergy.com
15
Acuvim II Series - AXM WEB PUSH
• Press Pto move to the N05 DNS Primary Server page. This is the primary DNS setting of
the meter.
• To con󳆂gure the DNS press V/A to enter edit mode, the cursor of the 󳆂rst digit will begin to
󳆃ash.
• Press the H button to scroll through the digits, and then press either P or E to change the
value of the digit. Once the primary DNS server address is entered in press V/A to con󳆂rm
the setting.
NOTE: The DNS parameters must be set correctly to use the SMTP, FTP/HTTP Post and Acu-
Cloud functions.
• Press Pto move to the N06 DNS Secondary Server page. This is the secondary DNS serv-
er setting of the Acuvim II meter.
• Press V/A to enter edit mode, the cursor of the 󳆂rst digit will begin to 󳆃ash.
• Press the H button to scroll through the digits, and press the P or E to change the value
of the 󳆃ashing cursor. Once the secondary DNS server address is entered press V/A to con-
󳆂rm the setting.
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
16
• Press Pto move to N07 Modbus Port page. This is the Modbus port setting of the meter,
the default is 502 and the range is from 2000-5999.
• To con󳆂gure the Modbus port press V/A to enter edit mode, the cursor of the 󳆂rst digit will
begin to 󳆃ash.
• Press the H button to scroll through the digits, and then press the P or E button to change
the value of the digit. Once the Modbus port is con󳆂gured press V/A to con󳆂rm the set-
ting.
V: 1.36 Revised: June. 2020

www.accuenergy.com
17
Acuvim II Series - AXM WEB PUSH
• Press P to move to the N08 HTTP Port page. This is the meters HTTP port setting screen,
the default is 80 and the range is from 6000-9999.
• To con󳆂gure the HTTP port press V/A to enter edit mode, the cursor of the 󳆂rst digit will
begin to 󳆃ash.
• Press the H button to scroll through the digits, and then press the P or E button to change
the value of the digit. Once the HTTP port is con󳆂gured press V/A to con󳆂rm the setting.
• Press Pto move to the N09 NET REST page. After making any changes to the NET settings
(pages N01-N08), users must reboot the Ethernet module from this page in order for the
settings to take e󳆁ect.
• To perform the reboot press V/A to enter edit mode, the cursor will begin to 󳆃ash. Press
the P or E button to change the setting to RESET and press V/A to con󳆂rm to reset. The
cursor will return to NO once successful.
V: 1.36 Revised: June. 2020

Acuvim II Series - AXM WEB PUSH
www.accuenergy.com
18
After con󳆂guring the AXM-WEB-PUSH module, press the H and V/A buttons simultaneously, the
screen will go blank and Setting will be 󳆃ashing. From here users can press either the P or E
buttons to navigate to Meter and then press V/A to navigate back to the main metering page.
V: 1.36 Revised: June. 2020