ACDelco ARI810 Dimensional drawing

ARI810
IMPACT WRENCH
PRODUCT INFORMATION MANUAL
Manuel informations du produit
Manual información del producto
English
Français
Español
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTE CONCERNANT LA
SECURITE, L'OPERATION, LA MAINTENANCE ET LE STOCKAGE DE CE
PRODUIT.
ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE ACERCA DE LA
SEGURIDAD, FUNCIONAMIENTO, MANTENIMIENTO Y ALMACENAMIENTO DE
ESTE PRODUCTO.
DO NOT ATTEMPT TO OPERATE THE TOOL UNTIL YOU HAVE READ AND UNDERSTOOD ALL
INSTRUCTIONS AND SAFETY RULES CONTAINED IN THIS MANUAL. FAILURE TO COMPLY
MAY RESULT IN ACCIDENTS INVOLVING FIRE, ELECTRIC SHOCK, OR SERIOUS PERSONAL
INJURY. SAVE THIS OWNER’S MANUAL FOR FUTURE REFERENCE AND REVIEW IT
FREQUENTLY FOR SAFE OPERATION.
NE PAS TENTER D'OPERER L'OUTIL TANT QUE VOUS N'AVEZ PAS LU ET COMPRIS TOUTES
LES INSTRUCTIONS ET REGLES DE SECURITE CONTENUES DANS CE MANUEL. SINON VOUS
RISQUEZ DES ACCIDENTS TELS QU'UN INCENDIE, UNE ELECTROCUTION, OU DES
BLESSURES CORPORELLES GRAVES. CONSERVEZ CE MODE D'EMPLOI EN CAS DE BESOIN ET
RELISEZ-LE SOUVENT POUR UTILISER VOTRE OUTIL EN TOUTE SECURITE.
NO UTILICE ESTA HERRAMIENTA HASTA HABER LEÍDO Y COMPRENDIDO TODAS LAS
INSTRUCCIONES Y NORMAS DE SEGURIDAD CONTENIDAS EN ESTE MANUAL. SI NO LO
HACE PODRÍA PROVOCAR ACCIDENTES CON FUEGO, DESCARGA ELÉCTRICA O LESIONES
PERSONALES SERIAS. GUARDE ESTE MANUAL DE INSTRUCCIONES PARA SU CONSULTA EN
EL FUTURO Y REVÍSELO FRECUENTEMENTE PARA UN USO SEGURO.
40732478-NA

1English1
English -1
THANKS FOR CHOOSING THIS PRODUCT
ACDelco provides you with products at an affordable price, and we would like you to
be fully satisfied with this product and our technical support. If any help or advice is
needed, please kindly contact us.
INTENDED USE
This tool is intended for personal use only.
This Impact Wrench is designed to remove and install threaded fasteners.
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term "power tool" in all of the warnings
listed below refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
NOTE provides additional information that is useful for proper
use and maintenance of this tool. If a NOTE is indicated make
sure it is fully understood.
DANGER
NOTE
CAUTION
WARNING
WARNING

1English1
English -2
WARNING LABEL IDENTIFICATION
Read Manuals Before Operating Product.
Wear Eye Protection.
Wear Hearing Protection.
Wear Dust Mask.
Wear Respiratory Protection.
Power tools can vibrate in use.
Do not carry the tool by the cord.
Keep body stance balanced and firm. Do not overreach when operating this
tool.
IMPORTANT SAFETY RULES
When using power tools, always prevent exposure and breathing of harmful
dust and particles.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
WARNING: Handling the power cord on corded products may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
DANGER

1English1
English -3
WORK AREA
Keep work area clean and well lit. Cluttered and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
ELECTRICAL SAFETY
Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices can
reduce dust-related hazards.
WARNING
WARNING
WARNING

1English1
English -4
TOOL USE AND CARE
Use clamps or other practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or off
position before making any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of starting the tool
accidentally.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can make
a connection from one terminal to another. Shorting the battery terminals together
may cause sparks, burns, or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edge are less likely to bind and are easier to
control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
CAUTION

1English1
English -5
BATTERY TOOL USE AND CARE
Ensure the switch is in the off position before inserting battery pack. Inserting
the battery pack into power tools that have the switch on invites accidents.
Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
battery pack.
Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can make
a connection from one terminal to another. Shorting the battery terminals together
may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact.
If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irritation
or burns.
SERVICE
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
CAUTION

1English1
English -6
SPECIFIC SAFETY RULES AND SYMBOLS
Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring. Contact with ’live’ wire will also
make exposed metal parts of the tool ’live’ and shock the operator.
Be aware that this tool is always in an operating condition, because it does not
have to be plugged into an electrical outlet. Always set the trigger switch to the
locked OFF position when installing or removing the battery pack or bits.
Do not use bits or sockets larger than those recommended. Large bits or drills
may overload the wrench/driver and damage the motor and gears.
Do not use if chuck jaws or other parts are cracked or worn.
Never change direction of rotation until motor has completely stopped.
Never hold work in your hand, lap, or against other parts of your body when
driving.
Do not use drill as a router or try to elongate or enlarge holes by twisting the
drill bit. Drill bits may break and cause injury.
Keep hands away from rotating parts.
Keep drill bit clear of yourself and all objects while installing and removing bit.
Some wood contains preservatives which can be toxic. Take extra care to prevent
inhalation and skin contact when working with these materials. Request, and follow,
all safety information available from your material supplier.
SYMBOLS
The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
SYMBOL NAME EXPLANATION
V Volts Voltage (potential)
no No Load Speed No-load Rotational Speed
kg Kilograms Weight
Direct Current Type of Current
…/min Revolutions per
Minute
Revolutions, Surface Speed, Strokes, etc.
per Minute
CAUTION

1English1
English -7
FUNCTIONAL DESCRIPTION
CONTROLS AND COMPONENTS:
1. Aluminum Gearbox Housing 2. Anvil (ARI810 : 3/8” | ARI810-2: 1/4”)
3. Built-in LED light 4. Forward / Reverse Control Button
5. Variable Speed Switch 6. Anti-slip Soft Grip
7. Battery Pack Release Button 8. Battery Pack
4
3
2
1
7
6
5
8

1English1
English -8
SPECIFICATIONS
Model Number ARI810 ARI810-2
Voltage 8 Vdc
Drive 3/8” Square 1/4” Square
Max. Tightening Torque 75 ft-lbs (100 Nm) 66 ft-lbs (90 Nm)
Max. Reverse Torque 115 ft-lbs (155 Nm) 103 ft-lbs (140 Nm)
No Load Speed 0-2,600 RPM (/min)
Impacts per Minute 0-3,100 IPM
Tool Weight 1.87 lbs (0.85 kg) 1.87 lbs (0.85 kg)
ASSEMBLY
INSTALLING OR REMOVING BATTERY PACK
TO REMOVE BATTERY PACK: Depress the battery pack release button (7) and pull
the battery pack (8) out of tool.
TO INSTALL BATTERY PACK: Push the battery pack (8) onto tool until it locks in
place.
INSTALLING SOCKETS
Always follow the procedure below to install a socket.
1. Insert a socket into the anvil (2).
2. Make sure the bit is fixed in the anvil while clicking on the ball of the anvil.
REMOVING SOCKETS
Always follow the procedure below to remove a socket.
Always set switch (5) to off position when installing and
removing socket.
CAUTION

1English1
English -9
OPERATION
Always check the direction of the rotation before use.
1. After continuous use, allow the impact wrench to sit idle for 15 minutes before
replacing the battery. The temperature of the motor, switch, etc., will rise if the
work is started again immediately after the battery has been changed, eventually
resulting in burned-out.
2. Place the point of the bolt in the socket. Keep the tool pointed straight at the bolt.
3. Apply forward pressure to the tool to prevent the socket from slipping off the bolt.
4. To start, turn impact wrench/driver on. Always check torque with a torque wrench.
The fastening torque can be affected by many factors including the following:
Voltage: Low voltage due to a nearly discharged battery will reduce the fastening
torque.
Socket Size: Failure to use the correct socket size will cause a reduction in fastening
torque.
Variable Speed Trigger Switch: Operating the tool at a reduced speed will reduce the
fastening torque.
Bolt Size: Larger bolt diameters generally require higher fastening torque. Fastening
torque will also vary according to length, grade, and torque coefficient.
Material: The type of material and surface finish of the material will affect fastening
torque.
Fastening Time: Longer fastening time results in increased fastening torque. Using a
longer fastening time than recommended could cause the screws to be overstressed,
stripped or damaged.
Continuous use in variable speed range is not recommended. It may
damage the switch and should be avoided.
When change the position of the control button, making sure the variable
speed switch is released.
The first time the tool is run after changing the direction of rotation, you
may hear a click on start up. This is normal and does not indicate a problem.
NOTE
NOTE
NOTE
NOTE