Acer AcerView 34e User manual

User’s Guide 1
AcerView 34e (14”monitor, 13.1”viewable image)
Installing the Monitor
Product Package
Open the shipping carton and check the contents. If any item is missing or damaged,
contact your dealer immediately. The package should include the following items:
ŸColor monitor ŸPower cord ŸUser‘s guide
ŸSwivel base ŸSignal cable
Installing the Swivel Base
Follow these steps to install the swivel base:
1. Turn the monitor on its side.
2. Insert the pegs on the swivel
base into the cavities at the
bottom of the monitor. Push
on the swivel base until the
latch clicks shut.
Installing the Monitor
Follow these steps to install the monitor:
This monitor is equipped with a universal power supply (90-264
VAC) . Before connecting cables, turn OFF the monitor.
Plug the 15-pin D-sub signal cable to the video signal
connector at the rear of the system.
Connect the power cord.

2User’s Guide
Control Functions
The monitor digital control functions are located on the front panel. Their description
are shown in the figure below.
Power Switch 5. Pincushion 9. Horizontal Size
Adjust 6. Vertical Center 10. Contrast
Select 7. Vertical Size 11. Brightness
Trapezoid 8. Horizontal Phase
Select / Adjust
Press the SELECT or button to cycle through the adjustment options to
choose H-Phase, H-Size, V-Center, V-Size, Contrast, Brightness, Trapezoid, and
Pincushion. And then press ADJUST or button to change the settings.
Reset
Reset all settings to factory defaults by pressing both function keys of SELECT
and ADJUST .

User’s Guide 3
Display Modes Memory
Our microcontroller feature has the memory capacity to store 24 different display
modes, divided into two parts: 16 modes for the user setting area and 8 factory preset
display modes
Power Saving Feature
This monitor’s power saving feature complies with VESA power saving modes.
Specifications
Picture tube
Size:
Dot pitch:
Surface/transmission:
14-inch (35.5 cm) diagonal
0.28 mm
Non-glare/semi-tinted
Maximum viewable size 13.1-inch (33.3 cm) diagonal
Video input 15-pin, D-sub connector, analog (positive)
Bandwidth 65 MHz
Display area 260 mm x 195 mm (H x V)
Power supply
(Universal)
Input voltage:
Consumption: 90V~264V / 47~63 Hz
85 watts maximum
External controls Power switch, brightness, contrast, adjust,
select, pincushion, V-size, V-center, H-size, H-
phase, trapezoid, reset
Horizontal frequency 30 ~ 54 KHz
Vertical frequency 50 ~ 120 Hz
Dimensions (with stand) 352 mm x 356 mm x 378 mm (W x H x D)

4User’s Guide
Ambient temperature
Operating:
Nonoperating: 10°C ~ 40°C
-40°C ~ 60°C
Humidity
Operating:
Storage:
20% ~ 90%
10% ~ 90%
X-Radiation DHHS, PTB
Regulatory
Compliance FCC-B, UL, CSA, BZT-B, CE, TÜV, D.N.S.F,
VCCI, MPRII (Optional), ISO9241-3
Factory Preset Display Modes
Mode Resolution V. Frequency H. Frequency
IBM VGA 640 x 400 70 Hz 31.50 KHz
IBM VGA 640 x 480 60 Hz 31.50 KHz
VESA VGA 640 x 480 75 Hz 37.50 KHz
SVGA4 800 x 600 75 Hz 46.88 KHz
UVGA1 1024 x 768 60 Hz 48.30 KHz
VESA VGA 640 x 480 72 Hz 37.86 KHz
SVGA2 800 x 600 60 Hz 37.88 KHz
SVGA3 800 x 600 72 Hz 48.09 KHz
FBesides above factory preset display modes, this monitor can display
the horizontal frequency from 31KHz to 54KHz. And the manual
alignment will be needed in some cases out of preset modes.