acerpure aqua WP742-40W User manual

Model : WP742-40W
Hot & Cold Water Purifier User Manual

Safety Instructions
Product Conguration and Structure
Display Panel and Function Buttons Introduction
Operating Instructions
Filter Replacement
Before Seeking After-sales Service
Product Specications and Company Information
02
03
04
06
09
09
11
Table of Contents

02
Safety Instructions
Note
Prohibition
1. This product is for family and oce use. Do not use it for other purposes.
2. Please make sure the power cable are not damaged before use and do not bend or pull the power cord to
avoid poor contact. If the power cable is damaged, it must also be replaced by authorized repair personnel
in order to avoid danger.
3. Before use, please check if the voltage matches the label on the product and do not use the universal
electrical outlet with other electrical appliances at the same time.
4. Switch o the power before unplugging the plug. Do not touch the power plug with wet hands to prevent
the danger of electric shock.
5. To avoid danger, please place the product on a at surface (the tilt angle of the surface should not be more
than 10°).
6. Stop using the product when the inlet water temperature or ambient temperature is below 5°C or above 38°C.
7. After taking higher temperature water or taking lower temperature water immediately, the water
temperature may be higher when it just comes out. Please use it carefully to avoid burns.
8. When the tap water used does not meet the government's tap water standards (e.g., large sediment content,
TDS exceeds the standard), the lter life of this product may be shortened as a result.
9. This product is not intended for use by users (including children) with physiological, perceptual, mental
ability, experience or knowledge deciencies unless used safely under the supervision or guidance of the
person responsible for their safety.
10. Unplug the power plug if this product is not used for an extended period of time. Especially when there
are emergencies such as thunder and lightning, earthquakes or res, please switch o the power and
unplug the power plug immediately.
11. This product only requires external cleaning and maintenance; do not clean the surface with rough cleaning
tools, and do not rinse it with water directly.
12. This product may not be repaired or modied by repairers who are not authorized by our company. If you
discovered any abnormalities such as noises, smoke or strange odors, please switch o the power
immediately, unplug the power plug and contact customer service personnel.
13. Please refer to the company information at the end of this manual on how to contact customer service.
14. This product has been tested before leaving the factory. If there is some vapor inside the product, it is a
normal phenomenon.
15. Please be sure to use lters from original manufacturer to ensure stable quality and product warranty.
1. Do not move the product at will. If you need to move it for any reason, please empty the water in the
tank before moving it.
2. Do not add turbid tap water, ice cubes or other liquids such as milk, juice, etc., to the water tank.
3. Do not put the water outlet deep inside the cup when receiving water to avoid the danger of the water
outlet being blocked by hot water.
4. Do not suspend the water container. Place it on a at surface.

03
Product Configuration and Structure
Product Structure
1
4
2
5
6
7
3
8
9
acerpure
aqua
Model : WP742-40W
User manual for ice, warm, instant hot water purifying dispenser






1Display Panel 2Water Outlet 3Transparent Hydrogen Water Window 4Water Tank Cover
5Water Tank 6Host 7Water Case 8Concentrated Water Tank 9Original Water Tank
Thank you very much for purchasing this product. Please make sure to read this
manual carefully, use this product correctly, and store it properly
Main Unit + Water Case Filters User Manual + Warranty Card +
Bottom Leak-proof Spare Parts
* The parts have been already
installed in the machine and
spare ones are provided for
potential loss or wear.

04
Display Panel and Function Buttons Introduction-1
｜功能鍵｜
-Filter Replacement Button-
After replacing the filter and turn on the
machine, please press this button for 3
seconds to enter the filter selection mode,
then select the filter you need to replace,
and finally press and hold it
for 3 seconds to complete the filter reset.
-Up and Down Adjustment Buttons-
Touch this button to select to display
water temperature, water volume or TDS
value and you can also adjust water
temperature or volume within a limited
range by this button.
-Normal Temperature Water-
Water temperature can be adjusted to
normal temperature by this button before
water is dispensed.
-Cold Water-
Before dispensing, the water
temperature can be adjusted to cold
water by this button.
-Hot Water-
Before dispensing, the water temperature
can be adjusted to hot water by this button.
-Smart Wash Button-
Use this button to wash and drain the
internal water circuit and water tank.
Short press once: Immediate TDS value
is displayed in the middle of the panel.
Press and hold for three seconds: Smart
wash starts, and the wastewater is
discharged from the outlet after three
minutes. Please make sure to prepare
water containers in advance to receive
water.
-Power Button-
You can start or stop using this product.
*In standby mode, please press and hold
for 2 seconds to turn on the product, and
in power on mode, you can press and hold
for 2 seconds to enter standby mode.
-Direct Water Dispense Button-
You can use this button to take the
water with normal temperature and
default volume. When the water
dispensing exceeds 500ml, the water
dispensing will be stopped automatically.
-Large Cup Volume Water Dispense Button-
You can use this button to dispense water in
a large cup volume (300ml by default).
-Small Cup Volume Water Dispense Button-
You can use this button to dispense water in
a small cup volume (150ml by default).
-Child Lock-
It is designed to prevent burns. When
taking hot water, you need to press the
child lock first, press Hot Water Button
and then Direct Water Dispense Button
to take hot water.
｜Function button｜

05
Display Panel and Function Buttons Introduction-2
-Filter Life Indicator-
You can check the status of the filter
life by this indicator. When the indicator
light is orange, it means that only 20%
of the filter life is left. When the
indicator light is red, it means that the
filter is exhausted and needs to be
replaced immediately.
-Out of Water Indicator-
When this light is on, it means that
the water tank is out of water, so
you need to wait until the water
production is finished before you
can take water.
-Water Change Indicator-
You can get the water change indication
by this indicator. When it is on, it means
the original water tank is short of water
and needs to be changed. Please add
tap water to the original water tank.
-Malfunction Indicator-
When the malfunction indicator is
on, please see page 10 for
troubleshooting or contact acerpure
customer service.
-Hydrogen Production Indicator-
You can check the working status of
the hydrogen production system by this
light. When the indicator is on, it means
the hydrogen production is in progress,
and when it is off, it means the
hydrogen production is finished.
-Water Purification Indicator-
You can use this indicator to check
the status of the water dispenser's
water production. When the indicator
is on, it means that water filtration is
in progress.
｜Indicator｜

06
Please press Cold water, and then press Direct water
dispense button for cold water dispensing.
Normal temperature
water dispense
Cold water dispense
Please press Direct water dispense button for
normal temperature water.
( Press and hold the cold water button for 5 seconds to turn off the
cold water production, and press again for 5 seconds to turn on the
cold water production. )
Operating Instructions
First time use
Regulate water temperature
Please place the product on a table or a flat area for smart wash and
drainage and pay attention to the maximum water level of the product.
1Please remove the original water tank and
add tap water, then install the original water
tank back to the main unit and put on the
water tank cover.
4When the water change light is on, please
add tap water into the tank. Machine will
start to produce the purified water
automatically.
(We suggest users wash the tank regularly
to ensure the best water quality.)
2After inserting the plug, please
press and hold the power button for
2 seconds to turn on the product.
3Press and hold the smart wash button for
cleaning, place a water container (such as a
bucket) at the water outlet and wait for
about 6-10 minutes for the water tank to
drain from the main unit before turning off
the machine (1-2 times for first time use).
Concentrated
Water Tank
Original
Water Tank

07
Operating Instructions
1 2 3
Preset water temperature
Adjustment range
70°C 85°C 95°C
40~95°C
Small cup volume
water dispense
Please press the child lock to
unlock and then press the hot
water button. There are three
hot water temperatures (70°C,
85°C and 95°C by default).
Please press the direct
water dispense button for
hot water that meets
your temperature
requirements.
To adjust the water
temperature: select a water
temperature range and
adjust the value by the up
and down buttons.
1For the predetermined water
volume of 300ml, select the large
cup volume of water and then
select the water temperature.
For the predetermined water
volume of 150ml, select the small
cup volume of water and then
select the water temperature.
2Select the large cup volume of water and
then press the up and down buttons to
adjust the water volume in units of 50ml
(volume range: 150~500ml); after the
adjustment, press the direct water
dispense button, and you can dispense
the water.
12Select the small cup volume of water and
then press the up and down buttons to
adjust the water volume in units of 50ml
(volume range: 150~500ml); after the
adjustment, press the direct water
dispense button to dispense the water.
Please note that there is a fixed range for hot water temperature adjustment. Please see
this table for the range.
Adjust the preset value of hot water temperature: Unlock first, touch the hot water button and
select one from 70/ 85 /95 °C. Press and hold the hot water button for three seconds to enter
the setting mode. Use the up and down buttons to adjust the preset value. After selection, stop
the action for three seconds. The machine is now set up and will stop flashing.
Regulate water dispensing
Large cup volume
water dispense
Regulate water temperature
Hot water
dispense

08
Operating Instructions
Filter Replacement
Filter Installation
Please turn off the power and unplug the product before replacing the filter.
1Turn the filter out counterclockwise and
pull it upward.
2
1Install a new filter and fasten it clockwise
to the end.
2Press and hold the reset button for 3 seconds,
then touch the reset button to select the
corresponding filter, and finally press and hold
for 3 seconds to complete the reset.
Press the button and the water tank
cover will pop open automatically.

09
Filter Function and Replacement Cycle
Abbreviation of lter Type of lter Recommended
replacement cycle
PCF
RO
GAC
Polypropylene & Carbon
Block Composite Filter
Reverse Osmosis
Membrane Filter 200G
Granular Activated Carbon Filter
6-12 months
12-24 months
6-12 months
Before Seeking After-sales Service
Problem Possible cause Solution
Product does not Is the power plug plugged in the
Is there enough water in the water tank?
Is the lter blocked because it is too dirty?
Is the lter too dirty or exceeding the
use time for a replacement?
Is the lter too dirty or exceeding the
use time for a replacement?
Have the parts on the machine been
disassembled by yourself?
Are the silicone seals in the water
seepage area aged or damaged?
Is the product placed on an unstable
surface or is there a water leak in the
machine?
Is the power plug plugged in the
socket properly?
Is the power plug plugged in the
socket properly?
Has the hydrogen production been
completed or has water window been
Is there any water in the small water
tank?
Please plug the power plug for this
product in the socket correctly.
Please add water to the original water tank.
Please verify the condition of the lter, and
clean or replace the lter in a timely manner.
Please verify the condition of the lter, and
clean or replace the lter in a timely manner.
Please verify the condition of the lter,
and clean or replace the lter in a timely
Please contact acerpure customer service.
Please make sure the product is placed
on a surface counter and check its water
leakage.
Please plug the power plug for this
product in the socket correctly.
Please plug the power plug for this
product in the socket correctly.
Please contact acerpure customer service.
Product cannot
Product water
The taste is not
satisfactory
Water seepage at the
screw connection
Electricity leakage or
product body with
electricity
Product cannot
produce hot water
Product cannot
produce cold water
Product cannot
produce hydrogen
If you discovered that the product malfunctioned,
please check the following items before contacting customer service.

10
Malfunction Code Description
Code Possible cause Solution
E1
If the water production does not stop for 90
minutes, the malfunction light will turn on
and E1 will be displayed in the numeric area
of the LED digit.
1. When the lter is dirty, resulting in poor
water production eciency. It is recommend-
ed to replace a new lter.
2. Please check if the lter is properly installed.
3. Please check if the water tank is properly
installed.
E2
When the water inlet circuit malfunctions, the
malfunction light will turn on and E2 will be
displayed in the numeric area of the panel.
Please contact acerpure customer service.
E3
When the water temperature thermal
resistance is open, the malfunction light
will turn on and E3 will be displayed in the
numeric area of the panel.
Please contact acerpure customer service.
Please contact acerpure customer service.
E4 When the inlet water temperature is in the
range of 0-1°C, the malfunction light will
turn on and E4 will be displayed.
Please use water that is 5-38°C.
E6 Heating circuit board malfunction
is detected.
E7 The heating element temperature is
too high.
Please stop using the machine rst and
wait for the temperature to decrease. Then,
it will automatically return to normal.

11
Company Information
www.acerpure.com
Product Specifications
Product name Hot & Cold Water Purifer
Product model WP742-40W
Rated voltage
220-240V/50-60Hz
100V/60Hz (For Taiwan specications only)
1500W (For Taiwan specications only)
Rated power
2200W
Working water pressure
475x240x430mm
Suitable water temperature
Net weight
Product dimensions
Country of origin China
0.4~0.8Mpa
5~38°C
10.989 kg