ACIQ ACiQ-24-AHB User manual

Congratulations on purchasing an ACiQ Next-Generation heat pump condenser. Using this
system in a dual fuel application will dramatically reduce your heating costs in the winter
compared to a standard system setup. The heat pump will provide heat in most conditions and
the furnace will provide backup heat at extreme low temperatures.
ACiQ-48-AHB/ACiQ-48-HPB
ACiQ-60-AHB/ACiQ-60-HPB
Dual Fuel System - ACiQ Heat Pump, 3rd Party Furnace, 3rd Party Coil
2023 V1.0
Quick Start Guide
ACiQ Next Gen Heat Pump Condenser
Dual Fuel
ACiQ-24-AHB/ACiQ-24-HPB
ACiQ-36-AHB/ACiQ-36-HPB

2023 V1.0
4. The selected thermostat must have a wired, wireless, or internet-based outdoor temperature sensing feature.
STANDARD HEAT/COOL ONLY THERMOSTATS WILL NOT WORK FOR THIS APPLICATION.
REFRIGERANT CONNECTIONS
Requirements
IMPORTANT: Line Set Size Requirements = 3/8" Liquid Line & 3/4" Suction Line.
1. The indoor coil (often referred to as the evaporator coil or A-Coil) must have a heat pump compatible Thermostatic Expansion
Valve (TXV).
2. The indoor coil must be sized correctly. At a minimum it must match the nominal BTU capacity of the selected outdoor unit. It is
permissible to oversize the indoor coil by up to 1 ton (12,000 BTU/H).
3. A 24 volt heat pump thermostat with a minimum of 2 stages of heating and 2 stages of cooling must be used (2H, 2C).
IMPORTANT: This system comes with copper adaptors that thread on to the outdoor unit. The other end of the adaptor has a
female sweat connection which allows for brazing the line set.
IMPORTANT: Purge with nitrogen during brazing! If you skip this essential step the abrasive, oxidative buildup will dramatically
shorten the compressor's life and void the warranty.
DO NOT
skip this step.
IMPORTANT: To ensure no leaks are present startup the unit in heating mode. While the unit is operating retorque the flare
adaptors (while unit is HOT). It is recommended to use a digital torque wrench.
IMPORTANT: Only a licensed and certified HVAC professional should complete the installation of this equipment. Please verify
your selected technician is section 608-certified.
Reference Guides
B
Set DIP Switches As Shown BelowOutdoor Unit DIP Switch Location On Circuit Board
Line Voltage Power - Must Also Connect
Ground Wire
Wired To Outdoor
Disconnect
L1
L2
W
Wired To Selected
Indoor Unit
Reversing Valve (Energized In Heating)
Heat/Cool Stage 2 (High Demand)
Heat/Cool Stage 1
24 Volt Common
IGNORE - DO NOT USE
IGNORE - DO NOT USE
IGNORE - DO NOT USE
24 Volt Hot (Power)
D
L
R
C
Y1
Y2

Thermostat wiring to the terminals on the
furnace will vary based on the brand of the
thermostat. Please refer to the thermostat
manual for furnace wiring. Look for a
section on dual fuel wiring. Some
thermostats send the call for backup heat
over the W terminals as shown. Some send
the backup call over Aux/E.
18/8 thermostat wire will be required
for correct low voltage wiring. A
common color scheme is shown in the
diagram, but please note colors may
vary. Many furnaces do not have an
O/B terminal. If this is the case connect
the orange O/B wires with a wire nut.
Example of a
wire nut. Please
note accurate
wire color is not
represented in
this photo.
Backup Heat Type: Set To Gas/Oil Furnace
Outdoor Temperature Sensing: Varies Based On Thermostat (Wi-Fi, Wired, Or Wireless Sensor)
Lockout/Switchover Temperature: Varies Based On Desire For Greater Efficiency Or Comfort. Maximum Comfort = 35 °F, Maximum
Efficiency = -10 °F, Our Recommendation = 0 °F
IMPORTANT – the heat pump and the furnace should NEVER run at the same time. Most heat pump thermostats are already
configured to prevent this from happening.
Typical Wiring Example
2023 V1.0
Thermostat Wiring
IMPORTANT – Every thermostat is different. Modern thermostats will have an “Installer Setup” or “Advanced Options”
mode. A dual fuel setup requires a heat pump compatible thermostat, which will call on the furnace only as backup heat at
extreme low temperatures. Here are general guidelines – refer to your thermostat manual for specifics.
Installer Setup & Advanced Options Settings
System Type: Set To Dual Fuel
Reversing Valve (O/B): Set To Energized In Heating Mode (Opposite Of Most Default Settings)