Acnodes APW5170 User manual

APW5170
17” 1920 x 1200 Widescreen LCD
A l u m i n u m F r o n t B e z e l
Panel/ V E S A M o u n t R e a d y
Industrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710 Tel: [phone] Fax: [phone]
© Copyright 2015 Acnodes Corp.

Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the
contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from
the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
●Unplug equipment before cleaning. Don’t use liquid orspray detergent; usea moist cloth.
●Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
●When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing dam
age to other equipment or injury to persons nearby.
●When the equipment is in an open position,donotcover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
●Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
●If you are using a power cord that didn’t ship with theequipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
●Observe all precautions and warnings attached to the equipment.
●If you don’t intend on usingthe equipment for a long time, disconnect it from the power outletto prevent being dam
aged by transient over-voltage.
●Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
●Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invali date its warranty.
●If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
●Any product, on which the serial number has been defaced, modified or removed.
●Damage, deterioration or malfunction resulting from:
●Accident, misuse,neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,or
failure to follow instructions supplied with the product.
●Repair or attempted repair by anyone not authorized by us.
●Any damage ofthe product due toshipment.
●Removal or installation of the product.
●Causes external to the product, such as electric power fluctuation or failure.
●Use of supplies or parts not meeting our specifications.
●Normal wear and tear.
●Any other causes which does not relate to a product defect.
●Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protectionagainst harmful interference in a residential instal- lation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
●Re-position or relocate the receiving antenna.
●Increase the separation between the equipment andreceiver.
●Connect the equipment intoan outlet on a circuit different from that to which the receiver is connected.

Contents
< Part. 1 > APW 5170
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & Installation
P.1
P.2 - 3
P.4 - 5
< Part. 2 > Specifications I OSD I Remote Controller
2.1 Product Specifications
2.2 On-screen Display Operation ( OSD )
2.3 Remote Controller ( RC-2 )
P.6 - 7
P.8 - 9
P.10
< Part. 3 > Options
3.1 Option Table
3.2 3G / HD / SD-SDI Broadcast-grade input
3.3 MCS Multi-display control solution
3.4 X17" Touchscreen : Resistive, Capacitive
3.5 48V, 24V or 12VDC power
3.6 MIL-type or lockable connector
3.7 TV ( Analog )
P.11
P.12
P.13
P.14
P.15
P.16
P.17

Before Installation
●It is very important to mount the equipment in a suitable cabinet or on a stable surface.
●Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in goodcondition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
●To avoidthe risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
●When you clean your monitor, do notpress down on the LCD screen. Pressing down on the screencan
scratch or damage your display. Pressure damage is not covered under warranty.
●Use onlycleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens canscratch the LCD displayor strip off the finish.
●Do notspray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
●Do notuse paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels canscratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1 Disconnect the power cord.
2 Gently wipe the surfaceusing a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, pleasefollowthese steps :
1 Disconnect the power cord.
2 Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or applyany liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directlyon the parts you are cleaning.
3 Gently wipe the surface. Use as little pressure as possible.
4 Wait until your monitor is completely dry before plugging itin and powering it up.

< Part 1 >
< 1.1 > Package Content –APW 5170
APW 5170
17” Widescreen LCD display X 1
6ft VGA cable X 1
Power cord X 1
Remote controller X 1
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screwx 8 pcs
Standard IIO
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
out - in - in
Video PC
HDMI
VGA
DVI-D
Audio
Power BNC S-Video

6
1
2
3
4
5
7
< 1.2 > Structure Diagram - APW 5170
Front view
1 Rear case
2 LCD panel
3 Protective 3mm glass
4 6mm aluminum front bazel
5 Audio speaker, pair
6 LCD membrane
7 Remote sensor
Rear view
Model
ProductDimension
(W x Dx H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
APW5170
469 x 57 x 331 mm
18.4 x 2.2x 13inch
615x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
5.5 kg
12.1 lbs
8 kg
17.6 lbs

< 1.2 > Dimension - APW 5170
Front View Side View
Rear View
UNIT : mm
1mm = 0.03937 inch
Bottom View

x 8 p
< 1.3 > Panel Mount Installation –APW 5170
1
Mounting
bracket
x 4 pcs
2
M4*6mm screw
x 8pcs
3
M4*50mm screw
cs
Hardwareset part no.UV-BK#2
Steps
●Install 4 mounting brackets with 8 x M4*6mm screws
●Adjust the LCD panel with 8 x M4*50mm screws and fix it on the surface.

¦
APW 5170
17” Industrial Panel Mount Widescreen LCD
< 1.3 > VESA mount Installation –APW 5170
M4 screw
VESAmount ( 100*100mm )
Hardware and M4*4 pcs for VESAmount are not provided

< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
APW 5170
Front Panel
Black, RAL 9005
Rear Casing
Dark grey, RAL 7037
VESAMounting
100 x 100mm
Other Mounting
Panel mount
Protection
3mm protective glass
LCD
Panel
Panel Size ( diagonal )
17.1-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1920 x 1200
Brightness ( typ. )
210
Contrast Ratio ( typ. )
600:1
Color
16.7M,8-bit
Viewing Angle ( L/R/U/D )
65/65/55/55
Response Time ( ms )
30
Dot pitch ( mm )
0.191
DisplayArea ( mm )
367.20H x 229.50V
Surface treatment
Anti-glare,Hard-coating
Surface hardness
3H
BacklightType
LED
MTBF ( hrs )
20,000
Video
Connectivity
Digital
HDMI
HDMI 1.1,CEA-861-D
DVI
DVI-D,TMDS single link
Analog
VGA
Analog 0.7Vp-p
Composite ( RCA)
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance/ Power level
30kK / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kK / 2.8V
SpeakerOutput
Power
2 x 2W
*When the audio outputisconnected, speaker output is OFF
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
34W or less
Power saving mode
4W or less
Power button OFF
1W or less

Regulatory
SafetyApproval
FCC & CE
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%,non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%,non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
469 x 57 x 331 mm
18.4 x 2.2 x 13 inch
Packing ( W x D x H )
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
Net Weight
5.5 kgs / 12.1 lbs
GrossWeight
8 kgs / 17.6 lbs
Applicable
Format
DVI-D /VGAInput
PC Signal
1920 x 1200 x 60Hz
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal
Sameas VGA
Video Signal
1080p : 60Hz
720p : 50 / 60Hz
480p : 60Hz
576p : 50Hz
Audio Signal
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
Composite / S-Video
Input
NTSC
525 lines, 60 fields / sec
PAL
625 lines, 50 fields / sec

< 2.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
1 Picture
Picture mode : Standard / Vivid / Soft / Usermode to choose
Brightness : Adjust background black level of the screen image
Contrast : Adjust thedifference between the image background
(black level) and the foreground (white level)
Hue: Adjust thescreen hue value
Saturation : Adjust thesaturation of the image color
Picture size : Adjust theimage size
Color temp : Standard / Cool /Warm / Userto choose
Noise reduce : Reduce the noiseof the image
Sharpness : Adjust theimage fromweak to sharp
2 PC
Auto adjust : Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock : Adjust theclock value
Phase : Adjust thephase value
H. Position : Align the screen image left or right
I. Position : Align the screen image up or down

< 2.2 > On-screen Display Operation ( OSD )
3 Audio
Audio mode : Movie / Voice / Normal / Music mode to choose
Volume : Adjust the volume of sound
Bass : Set the value of bass sound
Treble : Set the value of treble sound
Balance : Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute : Turn off the surrounding sound
5
MISC
Language :
Select the language in which the OSD menu is
displayed - English
Sleep timer :
Set the off time
PIP mode :
Adjust picture in picture setting
PIP position :
Enter into PIP position
PIP source :
Enter into the Sub source and sound source
System reset :
Return the adjustment back to factory setting
Information :
Select for Help
4
TV
Auto search :
Automatically search
Manual search :
Search the TV manual
Fine tune :
Fine tune the TV signal
Color system :
Adjust the TV color
Sound system :
Adjust the TV sound
Channel edit :
Edit the channel

< 2.3 > Remote Controller ( RC-2 )
1
8
2
INPUT MUTE
VOL
9
1 2 3
3
4 5 6
CH
10
7 8 9
4
AUTO 0
-/--
F REEZE 11
12
5
MENU SE LECT AS P ECT 13
14
6 ENTER
SLEEP
15
16
7
BACK EXIT PIP
17
PIP
20
S OURCE SWAP POSITION
AUDIO 18
PIP
21
19
r
1
INPUT Select thesource
2 Switcheson or off theTV
3
0 -9
Onlyusein TV mode. Selectchannels.Forchannel numbers 10
and above, enter the second digit withintwo seconds.
4 AUTO Auto adjust
5 MENU Displaythe menu on the screen or go tothe previous menu
Gotothe upper menuor selecttheprevious value /
Goto the next menu or selectthe next value /
6 ▲/ ▼/ ◄/ ►/ ENTER Decreasethe setting value /
Increasethe settingvalue or enter tothe select itemsetting
Enterto the select item settingsor excude the setting
7 BACK Backto previousvalue
8 MUTE Turn on or offthe speaker
9 Vol + I - Increase or decreasethe speaker volume
10 CH + I - ForTV model only, increase or decrease thechannel number
11 FREEZE ReserveforOEM model
12 - I -- For setting input single or double digits
13 ASPECT Adjust thescreen size
14 SELECT To selectthe existingitem
15 SLEEP Select thesleepingtime
16 EXIT Exitthe menuorcancel
PIP functions
17
PIP
Picturein picture
18
PIP AUDIO
To set the audioofin PIP mode
19
POSITION
To set thescreen positionin PIPmode
20
SOURCE
PIPSource
21
SWAP
Swapscreenin PIP mode

< Part 3 > Options
< 3.1 > Option Table
Options
APW
PMW
SDI ***
Touchscreen
MCS multi-displaycontrol***
DC Power
MIL-type / lockable connector
TV (Analog )
***
The user canonly select either SDI or MCS inputs.

APW 5170
17” Industrial Panel Mount Widescreen LCD
< 3.2 > Options : 3G I HD I SD-SDI input
Acnodes’ SDI input is an ideal solution for the broadcast-
grade videoandhigh resolution CCTVmarket.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it comes
standard with a 2-year warranty.
Power BNC S-Video Audio
out - in - in
Video PC
HDMI
DVI-D VGA SDI
out - in
INPUT
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
StandardCompliance
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
Compatible VideoFormat
3G-SDI
1080p
@60 / 50Hz, 4:2:2
1080p
@30 / 25 / 24Hz, 4:4:4
1080i
@60 / 50Hz, 4:4:4
720p
@60 / 50Hz, 4:4:4
HD-SDI
1080p
@30 / 25 / 24Hz, 4:2:2
1080i
@60 / 50Hz, 4:2:2
720p
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
CompatibleAudioFormat
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s

< 3.3 > Options : MCS
MCS
( Multi-display Control ) More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64units.
The RS-232C is used for the communication between the PC and
the first display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisychain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides
a MCS input module without using additional space or power
and it comes standard with a 2-year warranty.
MCS
RS-232C
Set switch
For the 1st and last display,
push the set switch upward
15 feet serial cable
( over 15 feet, extender required )
For other daisy chaindisplays,
push the set switch downward
LINK OUT IN OUT IN OUT IN
OUT
RJ-45 jack
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
Daisy chainup to 1,000
meters and 64 displays
Cat5 / 6 cable
max. 300 meters
up to 64 displays
Link
set out in
out - in - in
Video PC
HDMI
VGA
DVI-D
Audio
Power BNC S-Video

< 3.4 > Options : Touchscreen & driver
17" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-WireResistive
Capacitive
Touch Point
Single
Single
Method
Stylus or Finger
Finger
ActivationForce
=50g /Stylus=R0.8
= 50g
Durability
10 million touches
300 million touches
Response Time
15 ms
20 ms
OpticalTransmittance
80% ± 3%
92% ±2%
SurfaceHardness
3H
9H
Haze
8% ± 3%
7%
Glass
2.2 ±0.2 mm
2.8 mm ±10%
Connector
USB TypeA
Compatibility
Windows 7 / XP / Vista, Linux
● USB touchscreen package includes 1 x 6ft USB cable, quick referenceguideline and CDdisc
● For detailed information,please refer tothe attached CD disc
● As the touchscreen unit is notmade of toughened glass,pleasehandle itcarefully
USB Touchscreen
out - in - in
Video PC
VGA
DVI-D
HDMI
Audio
Power BNC S-Video

Please follow the below steps to setup the touch screen:-
Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installationinstruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please dothe initial calibration
after the first setup
.

< 3.5 > Options : DC Power
Model
12V
24V
48V
Input rating
Input voltage:
12-Volt
24-Volt
48-Volt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
Input current
- No load
50 mA
50 mA
50 mA
- Full load
4950 mA
2450 mA
1220 mA
Output rating
Output voltage:
12-Volt
12-Volt
12-Volt
Output current:
4.16A
4.16A
4.16A
Efficiency
84%
85%
85%