Acnodes PMW7043 User manual

PMW7043
Industrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710 Tel: [phone] Fax: [phone]
© Copyright 2019Acnodes Corp.
43” 4K LCD Display
Open frame metal construct ion
DP 1. 2 + HDMI 1. 4 + HDMI 2.0 video input

What the warranty does not cover
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modif cations made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Legal Information
First English printing, July 2019
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, f re or electrical shock.
■Only qualif ed service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualif ed service personnel.
■Any product, on which the serial number has been defaced, modif ed or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, f re, water, lightning, or other acts of nature, unauthorized product modif cation, or
failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power f uctuation or failure.
□Use of supplies or parts not meeting our specif cations.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.

Contents
< Part. 1 > PMW7043
1.1 Package Content P.1
1.2 Structure Diagram & Dimension P.2 - 3
1.3 Mounting Hardware & Installation P.4
P.5 - 6
P.7 - 9
P.10 -11
< Part. 3 > Options
P.12
P.13
P.14
P.15
P.16 - 17
P.18
Option Table
Remote Controller (RC-2)
3G / HD / SD-SDI Broadcast-grade input
MCS Multi-display control solution
Touchscreen & driver
DC Power
MIL-type or lockable connector P.19
< Part. 2 > Specifications / OSD/ Remote Controller
2.1
2.2
2.3
Product Specifications
On- Screen Display Operation (OSD)
Picture in Picture (PIP) / Picture by Picture (PBP)
3.1
3.2
3.5
3.6
3.3
3.7
3.4

■It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
Unpacking
Before Installation
How To Clean Your LCD Monitor
Caution :
3
4
■To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■Use only cleansers made specif cally for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the f nish.
■Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood
based paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
Disconnect the power cord.
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
1
2
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
2
Disconnect the power cord.
Spray a small amount of non-abrasive cleanser on a microf ber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microf ber cloth f rst, not directly on the parts you are cleaning.
Gently wipe the surface. Use as little pressure as possible.
Wait until your monitor is completely dry before plugging it in and powering it up.

43” 4K LCD Display
P. 1
< Part 1 > PMW7043
< 1.1 > Package Content
43” 4K LCD Display X 1
6ft DP Cable X 1
Power Cord X 1
Remote Controller X 1
PMW7043
Basic I/O
HDMI 1.4 HDMI 2.0 DP Power
out
Audio

P. 2
< 1.2 > Structure Diagram
3
5
4
Rear case
LCD panel
Universal open frame mounting
Audio speaker, pair
LCD membrane
Extended remote sensor membrane cable
( 66cm from AD board to sensor end )
1
2
3
4
5
PMW7043
1
2
6
6
Bottom view
Front View Side view
Rear View
Model Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
PMW7043 1022 x 74.8 x 616 mm
40.2 x 2.9 x 24.3 inch
1122 x 199 x 712 mm
44.2 x 7.8 x 28 inch
26.2 kg
57.6 lb
32 kg
70.4 lb

43” 4K LCD Display
P. 3
< 1.2 > Dimension
Front View Side View
Rear View
UNIT : mm
1mm = 0.03937 inch
PMW7043
Bottom View

P. 4
< 1.3 > Mounting Hardware & Installation
( I) Universal mount
( II ) VESA mount ( 600*400mm )
M8 screw
■Hardware and M8*4 pcs for VESA mount are not provided
VESA mount ( 600*400mm )

P. 5
< Part 2 >
< 2.1 > Product Specifications n43” 4K LCD Display
Mechanical Design PMW 7043
Protection open frame
Front Panel -
Rear Casing Black, RAL 9005
VESA mount 600 x 400 mm
Universal mount ready
Desktop Stand -
Panel Mount -
LCD Panel Standard Sunlight Readable
Brightness ( cd/m2) 350 1500
Contrast Ratio ( typ. ) 1000 : 1 1100 : 1
MTBF ( hrs ) 30,000 50,000
Panel Size ( diagonal ) 43-inch Widescreen TFT color LCD
Native resolution 3840 x 2160
Colors 1.07 Billion, 10-bit
Viewing Angle ( L/R/U/D ) 89/89/89/89
Response Time ( ms ) 12
Dot pitch ( mm ) 0.2451
Display Area ( mm ) 941.184H x 529.416V
Surface treatment Anti-glare
Surface hardness 2H
Backlight Type LED
Video
Digital Display port DP 1.2 / HDCP 1.3
HDMI HDMI 2.0 / HDCP 2.2
HDMI 1.4 / HDCP 1.4
Audio
Output
Connector 3.5mm stereo jack
Resistance / Power level 30kΩ/ 2.8V
Speaker:
Dual Stereo 10W x 2
*When the audio output is connected, speaker output is OFF
Power Standard Sunlight Readable
Input Auto-sensing 100 to 240VAC, 50 / 60Hz
Consumption:
Screen ON Max. 68W Max. 220W
Power saving mode Max. 9W Max. 9W
Power button OFF Max. 2W Max. 2W
Compliance
EMC FCC & CE certified
Safety CE / LVD certified
Environment RoHS2 & REACH compliant

< 2.1 > Product Specifications
Physical Specification
Product ( W x D x H )
mm
1022 x 74.8 x 616
inch 40.2 x 2.9 x 24.3
Packing ( W x D x H )
mm
1122 x 199 x 712
inch 44.2 x 7.8 x 28
Net Weight 26.2 kg / 57.6 lb
Gross Weight 32 kg / 70.4 lb
Chassis color Dark
Chassis materials Aluminum
P. 6
Environmental Conditions
Operating Temperature 0 to 55°C degree
Humidity 20~90%, non-condensing
Altitude 16,000 ft
Storage /
Non-operating
Temperature -20 to 60°C degree
Humidity 5~90%, non-condensing
Altitude 40,000 ft
Shock 10G acceleration ( 11ms duration )
Vibration 10~300Hz 0.5G RMS random vibration
Applicable Format
Display Port Input PC Signal 3840 x 2160 x 60Hz
1920 x 1080 x 60Hz
1600 x 1200 x 60Hz
1360 x 768 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 768 x 60Hz
1024 x 768 x 60 / 70 / 75Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
Audio Signal 2ch Linear PCM
HDMI Input HDMI 2.0 3840 x 2160 x 60Hz
HDMI 2.0 / 1.4 3840 x 2160 x 30Hz
1920 x 1080 x 50 / 60Hz ( 1080p )
1920 x 1080 x 25 / 30Hz ( 1080i )
1280 x 720 x 50 / 60Hz ( 720p )
720 x 480 x 50 / 60Hz ( 576p / 480p )
Audio Signal 2ch Linear PCM
* In some circumstances, if the user connects the LCD to PC via HDMI port for video and audio signals, the LCD may displa
incorrectly on a full screen. If so, please adjust the display card setting on display size to fix the issue.