ACP RMS A Series User manual

©2019 ACP, Inc.
Cedar Rapids, IA 52404 Part No. 20267702 Original Instructions
Quick Start Guide
Refer to Owner’s Manual for Safety Statements. Complete Owner’s Manual available online.
This document covers RMS*A and MMS*A models with touchpad controls
A
B
C
D
OVEN CLEARANCES
A. Allow at least 7” (17.78 cm) of clearance around top of oven. Proper air ow
around oven cools electrical components. With restricted air ow, oven may not
operate properly and life of electrical parts is reduced.
B. There is not an installation clearance requirement for the back of the oven.
C. Allow at least 1” (2.54 cm) of clearance around sides of oven.
D. Install oven so oven bottom is at least 3 feet (91.5 cm) above oor.
Preset Program Keys
To cook food using preprogrammed
cooking sequences:
1. Open oven door and place food in
oven. Close door.
2. Press desired Number Key
3. Oven begins cooking
4. At the end of the cooking cycle,
the oven beeps and LED displays
“End”.
X2 - Double Quantity
Cooking
1. Open oven door and place food in
oven. Close door.
2. Press X2 key .
3. Press desired Preset Program
Number Key(s). LED displays the
cooking time for two quantities.
The oven will start cooking per the
quantity preset cooking time.
The switching operation of this microwave oven can cause voltage uctuations on the supply line. The operation of this oven under unfavorable
voltage supply conditions can have adverse e󰀨ects. This device is intended for the connection to a power supply system with a maximum
permissible system impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected
only to a power supply system which fullls the requirement above. If necessary, the user can ask the public power supply company for the
system impedance at the interface point.
So…how do I use it? (Electronic Control)
Manual Time Entry Mode
Time entry mode allows the user to manually enter a cook time and power level.
1. Open oven door and place food in oven. Close door.
2. Press the TIME ENTRY key .
3. Press Number Keys to enter the desired cook time.
4. Press POWER LEVEL key , , or to change power level if desired.
5. If stage cooking is desired, press TIME ENTRY key and repeat steps 2-4.
6. Press START key to begin cooking.
7. At the end of the cooking cycle, the oven beeps and LED displays “End”.
Programming Mode
1. Open oven door and press and hold Number Key “1” for 5 seconds.
2. Press a Number Key to change or review a Preset Program setting.
3. Press Number Keys to enter the new desired cook time.
4. Press POWER LEVEL key , , or to change power level if desired.
5. If stage cooking is desired, press TIME ENTRY key and repeat steps 3-5.
6. Press START key to save the cooking program.
7. Close the door to exit Programming Mode.
Note: If STOP/RESET key is pressed before programming is
complete,changes are discarded and microwave exits programming mode.

©2019 ACP, Inc.
Cedar Rapids, IA 52404 Part No. 20267702 Original Instructions
For full product documentation visit:
www.acpsolutions.com
User Option Mode
There are several options you can change to customize the operation of the oven for
your business. The table below shows these options;
the factory setting is shown in bold type.
1. Open oven door and press Number Key “2” for 5 seconds.
2. Press any Number Key to enter related options as noted in chart below.
3. To change, repeat pressing the Number Key until desired setting is reached.
4. Press START key to save the selected setting.
5. To exit User Option Mode, press STOP/RESET key and close door.
Quick Start Guide
Refer to Owner’s Manual for Safety Statements. Complete Owner’s Manual available online.
Refer to Owner’s Manual for complete care
and cleaning instructions.
⚠Do NOT use abrasive cleaners or cleaners
containing ammonia, citrus, phosphates, chlorine,
sodium or potassium hydroxide (lye).
Use of unapproved cleaning agents will void
the terms of the warranty.
No metal pans
No metal pans
DO NOT power spray
DO NOT power spray
NUMBER KEY DISPLAY OPTIONS (FACTORY SETTINGS IN BOLD)
1
End of Cycle Beep
OP:10
OP:11
OP:12
3 second beep
Continuous beep until door is opened
5 beep bursts until door is opened
2
Key Beep Volume
OP:20
OP:21
OP:22
OP:23
Eliminates beep
Sets volume to low
Sets volume to medium
Sets volume to high
3
Key Beep
OP:30
OP:31 Prevents beep when pad is pressed Allows beep when pad is pressed
4
Active Display
OP:40
OP:41
OP:42
OP:43
15 seconds after oven door is opened, keyboard disabled
30 seconds after oven door is opened, keyboard disabled
1 minute after oven door is opened, keyboard disabled
2 minutes after oven door is opened, keyboard disabled
5
On-the-Fly Cooking
OP:50
OP:51 Prevents di󰀨erent pre-programmed pads to be activated during cooking Allows di󰀨erent pre-programmed pads to be activated during cooking
6
Reset Door Open OP:60 OP:61 Allows oven to resume heating time countdown after door is opened during cycle Cancels heating time count down after door is opened during cycle.
7
Maximum Heating
Time
OP:70
OP:71 Allows 30 minutes of heating time Allows 10 minutes of heating time
8
Manual Operation OP:80 OP:81 Allows use of preprogrammed pads only Allows use of manual time entry and preprogrammed pads
9
Double Digit
Operation
OP:90
OP:91 Allows 10 (0-9) preprogrammed pads Allows 20 (00-99) preprogrammed pads
*Note: Factory setting may vary by model