ACTi ACD-2200 User manual

4 CH Video Server
ACD-2200
Quick Installation Guide
Ver.070831

1 Getting Started
1.1 PACKAGE CONTENTS
ACD-2200 WarrantyCard
Software CD Terminal Blocks & Screws
PowerAdaptor(Option)
1

1.2 PHYSICAL DESCRIPTION
1. Channel Number
2. Video Input
Each channel supports one analog video input of composite signal with BNC
connectors.
3. Audio Input / Output
The video server supports one audio input and output with earphone jack.
4. ETHERNET Port
The Video server connects to the Ethernet via a standard RJ45 connector.
Supporting NWAY, this Video server can auto detect the speed of local network
segment (10Base-T/100Base-TX Ethernet). The Ethernet port is for FTTH and can
connect to a xDSL or cable modem.
5. Reset Button

Step 1: Switch off video server by disconnecting the power cable
Step 2: Using a suitable pointed object, press and continue to hold the Reset Button
depressed. While continuing to hold the reset button depressed, reconnect the
power cable.
Step 3: Keep holding the reset button depressed around 6 seconds, release the reset
button. The unit will start up with factory default settings.
6. Action LED Indicator
The LED will light up after video server has successfully completed the boot
process.
7. LAN LED Indicator
LEDs indicating when LAN is active.
8. Serial Port LED Indicator
LEDs indicating when serial port is active.
9. Terminal Blocks Pin 1~6
The video server supports two alarm input and two alarm output. DI: Logic Level 0:
0~0.4V; Logic Level 1: 3.3~30V DO: Logic Level 0: 0.1~0.6V; Logic
Level1: 2.4~5V
PIN NAME DESCRIPTION
1 DO1 Digital Output 1
2 DO2 Digital Output 2
3 GND Ground Pin
4 DI1 Digital Input 1
5 DI2 Digital Input 2
6 GND Ground Pin
10. Terminal Blocks Pin 7~12
Pin 7~10: RS232/422/485. Default mode is RS-485/422 auto-sensing.
Pin 11~12: DC 12V power input (Only Channel 1)

DESCRIPTION
PIN NAME RS-485 RS-422 RS-232*
7 Tx+ D+ Tx+ Tx
8 Tx- D- Tx-
9 Rx+ Rx+ Rx
10 Rx- Rx-
11 12V Power Input (DC +12V)
12 GND Ground Pin of Power Input &
RS-232
* RS-232 mode requires user to set the jumpers inside the video server.
Bcause opening the video server will void the warranty, please contact your
distributor for how to switch to RS-232 mode.

2 Quick Tour
This section guides you with a quick tour on video server.
2.1 Configure the Video Server
2.1.1 Make sure network environment
Default IP of video server is 192.168.0.100. Please make sure video server and
your PC are on the same network segment before running the installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)

2.1.2 Open Internet Explorer with IP address
zSTEP1: Open a browser
zSTEP2: Enter the IP address of the IP device.
The default IP address is “192.168.0.100”
The “Login Page” is now displayed as below.
zSTEP3: Enter the Account name (factory default: Admin) and the
Password (factory default: 123456).
zSTEP4: Select the language of the IP device user interface. You can
select from English, Traditional Chinese, Simplified Chinese, Japanese,
Spanish, Italian, German, Portuguese,Czech and French. This user
interface setting will disappear once you log out, if you want to change
the default user interface language, please change the setting of [Host
setting] after login successed.
zSTEP5: Click the button to login or click the button
to re-enter again.
Once successfully login, the “Main Setup page” will be displayed as below.
NOTE: Internet Explorer of 6.0 or above is highly recommended. If you
don’t have the it, please download it from
http://www.microsoft.com/windows/ie/downloads/default.mspx

zSTEP1: Click to set system configurations of 4-CH Video Server
zSTEP2: Click to apply the choice

2.1.3 Set New IP
Click the [WAN Setting] on the “Main Setup page”. The “WAN setting page” is
displayed as below.
*IP Address : The IP address of the LAN interface. The default IP address is
192.168.0.100.
*Subnet Mask : The subnet mask of the LAN interface.The default subnet mask is
255.255.255.0
*Click button

NOTE: Check with your MIS department, if Client PC and IP rugged dome
are setting in different VLANs, please connect to WAN port.
NOTE: In your Client PC, please make sure the setting of Network
Connections Type is set to Auto Negotation, since IP rugged dome follows
MII standard. Otherwise, you might not see the live image.
IMPORTANT: After the IP address is changed, please record this IP
address. There is no way to connect to the IP rugged dome if user forgets
the new IP address.

2.1.4 Save Reboot
zSTEP1: Click the [Save and reboot] on the “Main Setup page”.
The “Save and reboot page” is displayed as below.
zSTEP2: The Action LED indicator will light down to indicate that the
IP device is rebooting. After around 30 seconds, the Action LED will
light up again to indicate that the reboot is completed.

2.1.5 Configuring the IP device – Channel
This section describes how to configure the system part of IP device.
zSTEP1: Click to set configurations of every single channel of
4-CH Video Server
zSTEP2: Click to apply the choice

2.1.6 Preview the video
zSTEP1: Click the [Video Display] on the “Main Setup page”.
The “Video Display page” is displayed as below.
zSTEP2: Check the [Mute] checkbox to select mute enable/disable
zSTEP3: Click the [Audio Out] checkbox to enable/disable audio
output from control PC to IP device.
zSTEP4: Click the if you cannot see the video, and follow the
instructions.
zSTEP5: Click the [Quit] to exit the live view and return to “Main
Setup page”.

2.1.7 Check Default Video Setting
zSTEP1: Click the [Video Setting] on the “Main Setup page”.
The “Video setting page” is displayed as below.
zSTEP2: Clieck to enter the configuration table.

Click the [Apply] button of each setting to confirm the settings or click the
[Reset] button to re-enter the parameters.
NOTE: Please make sure the TV Input (NTSC / PAL) is meet your
requirement, and click button.