ActivePure Induct Guardian I User manual

C
READ MANUAL CAREFULLY FOR PROPER USE AND OPTIMAL OPERATION.

2
GENERAL INFORMATION
If you have any questions concerning this, or any ActivePure product,
contact ActivePure Customer Service at 800.572.1446 or email
[e-mail].
CONTENTS
Product Overview . . . . . . . . . . 2
Specifications. . . . . . . . . . . . 2
Storage and Disposal . . . . . . . . . 2
Important Safety Instructions. . . . . . 3
For Canadian Customers Only . . . . . 4
Product Features . . . . . . . . . . 5
Installation Hardware (Supplied). . . . . 5
Recommended Installation Tools . . . . 5
Installation Requirements . . . . . . . 6
Electrical Requirements . . . . . . . . 7
Installing the Unit . . . . . . . . . . 7
Wiring the Unit . . . . . . . . . . . 9
Maintenance/UV Bulb Indicator . . . . . 9
Changing the ActivePure®Cell . . . . . 10
Replacing the Ballast . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . 12
Replacement Parts & Service. . . . . . 13
Warranty Information . . . . . . . . . 13
FCC Declaration & Responsible Party . . 14
PRODUCT OVERVIEW
Congratulations on your purchase of the ActivePure®Induct Guardian I! The unit is easily mounted into the
supply side of air conditioning and heating system air ducts by an electrician or HVAC professional, where it
will provide 24/7 surface and air disinfection. Please read and follow all service procedures outlined in this
manual before installing or performing maintenance.
STORAGE AND DISPOSAL
Do not dispose of this product as household
waste. Electrical waste and electronic
products should be appropriately recycled as
required by practices established by your
local authority.
SPECIFICATIONS
ActivePure Induct Guardian I
• Model Number: B1013U
• Sales Number: 00761
Electrical:
• Input Voltage: 24 VAC; ~ 50/60Hz
• Current: 1.0 A
• Power: 17 Was
• Complies to UL 1598
Mechanical:
• Distribution via Air Handler
Safety Switch installed
Weight & Dimensions:
• 3 lbs (1.36 kg)
• 8.5” H x 8.5” W x 11” D
(21.59 cm x 21.59 cm x 27.94 cm)
Operating Temperature:
• 34 ºF to 200 ºF (1 ºC – 93 ºC)
Recommended Maximum Coverage in a
Contiguous Space1:
• Every facility is unique and proper
configuration is an important as the
technology. To validate coverage in your
facility, speak to your sales representative
or call customer service at 800-572-1446.
Warranty:
• Limited Five (5) Year Warranty
ActivePure Manufacturing, LLC reserves the right to
change or modify any specification without notice.

3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
• UV Light in operation; disconnect unit from power supply before
servicing; failure to follow warnings may result in severe eye damage
and electrical shock
• To prevent damage to the unit, operating environment temperature
must never exceed 200 oF (93 oC)
• DO NOT use this unit with an extension cord
• To reduce the risk of electric shock, this equipment may have a
grounding type plug that has a third (grounding) pin; this plug will
only fit into a grounding type power outlet; if the plug does not fit
into the outlet, contact qualified personnel to install the proper
outlet; DO NOT alter the plug in any way
• This unit is equipped with a universal ballast that operates at
nominal voltages between 100 and 240 VAC, 50/60 Hz
• To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations; this equipment emits UV-C radiation; DO NOT locate
equipment in any location allowing direct line-of-sight to vents,
returns, or other duct openings
 DO NOT connect this unit to any voltage source above 32 volts;
doing so will cause damage to the unit
WARNING
Location for Protective Earth Line.
CAUTION
• Wiring and installation of this unit must be done by a licensed HVAC
contractor or electrician; failure to do so will void warranty of the
product
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from the elements
Read this manual in its entirety before using your ActivePure®Induct Guardian I.
Keep out of the reach of children.
• Live voltage may be present
• Power Connection Requirements: This device is designed to operate using a 24 VAC, 40Va
transformer. Transformers supplied with a straight cooling or HVAC system may be used to
power the device but must be verified it’s capable of handling the additional device load before
installation. If the system transformer is not capable of handing the extra load, a separate 24 VAC,
40Va transformer MUST be used. Do not connect the device to any power source with a voltage
less than 22 VAC and a maximum of 32 VAC. Doing so will cause damage to the device
• Disconnect power at the breaker or fuse panel before servicing unit; always follow OSHA lockout
procedures to prevent accidental exposure to electrical energy
• If installed near a furnace or where emergency heat coils could raise the temperature inside the
plenum, cycle the AC unit through three full heating cycles assuring that the temperature never
exceeds 200 °F (93 ° C).The ActivePure®Cell must not exceed 200 °F (93 °C)
• If the unit is hard wired, be sure the power to the unit is o; always follow OHSA electrical lockout
safety requirements to prevent accidental release of energy during service or maintenance
activities
• Never aempt to check operation of the ActivePure®Cell(s) by direct observation; severe eye
damage can result; use the indicator lamps on the boom of the ballast on

4
FOR CANADIAN CUSTOMERS ONLY
ACTIVEPURE®INDUCT GUARDIAN I
Sales No. : 00761
This UV device helps reduce the spread of viruses in the air.
Keep out of the reach of children.
Please read the label and owner's manual before using: www.activepure.com/manuals
PRECAUTIONS:
WARNING: UV radiation emied from this device. Unintended use of the device, or damage to the housing,
may result in exposure to ultraviolet radiation. Ultraviolet radiation may cause eye and skin irritation. Avoid
exposing eyes and skin to ultraviolet radiation.
FIRST AID INSTRUCTIONS: Please contact your healthcare provider in the event of injury caused by this
device.
DIRECTIONS FOR USE:
Unit should be installed aer the air handler in the HVAC system by a licensed HVAC contractor or
electrician. Please see owner's manual for detailed instructions on using, handling, storing and disposing of
the device, and procedures to mitigate any associated risks.
The use of this device is a supplement to and not a substitute for standard infection control practices; users
must continue to follow all current infection control practices, including those related to the cleaning and
disinfection of environmental surfaces.
FOR INQUIRIES CONTACT:
AERUS CANADA, INC.
Laird Business Park
3480 Laird Road, Units 2–5
Mississauga, Ontario, Canada, L5L 5Y4
W. Parrell, Manager
[phone]
[email protected]
Aerus Canada, Inc. is ailiated with ActivePure Manufacturing, LLC
1300 Valley Drive, Bristol, VA 24201

5
It is important to be familiar with the parts of the ActivePure®Induct Guardian I. If any parts are missing,
contact your sales representative or ActivePure Customer Service.
PRODUCT FEATURES
C
Mounting PlateSafety Switch
Power Cord
UV Bulb
Indicator
Replaceable ActivePure Cell
(Includes UV Bulb)
INSTALLATION HARDWARE SUPPLIED
(8) #8 — .75 1/4" Self-tapping screws
Item # US7067
(2) Thumb screws
Item # 36-00213
(2) Thumb nuts
Item # 36-00214
(4) #6 — 32 x 2 inch Threaded bolts
Item # US70680 (4) #6 — 32 Toggle
bolt wall anchors
Item # US70682
RECOMMENDED INSTALLATION TOOLS
3 1/2" Hole Saw
(for wood or metal)
Utility Knife
1/4" Nut
Driver Bit
Drill / Power
Driver
Tin Snips
(for metal ductwork)
Phillips
Screwdriver
Dust Mask
3/8" Drill Bit
(if installing into fiberglass
ducting with toggle bolts)
1/4
YOU MAY ALSO NEED:
CAUTION
When the unit is installed in a roof mounted HVAC system, the unit must
be protected from elements.

6
• Power Connection Requirements: This device is designed to
operate using a 24 VAC, 40Va transformer; transformers
supplied with a straight cooling or HVAC system may be used
to power the device but must be verified it’s capable of
handling the additional device load before installation; if the
system transformer is not capable of handing the extra load,
a separate 24 VAC, 40Va transformer MUST be used; DO NOT
connect the device to any power source with a voltage less
than 22 VAC and a maximum of 32 VAC; doing so will cause
damage to the device
• If installed near a furnace or where emergency heat coils could raise
the temperature inside the plenum, cycle the AC unit through three
full heating cycles assuring that the temperature never exceeds
200 °F (93 °C); the ActivePure®Cell must not exceed 200 °F (93 °C)
WARNING
INSTALLATION REQUIREMENTS
CAUTION
• This unit must be installed by a licensed HVAC contractor or
electrician; failure to do so will void warranty of the product
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from the elements
1. The ActivePure®Induct Guardian I unit should be
installed aer the air handler in the HVAC system.
2. The ductwork around the installation area should
be clean and dry to ensure proper adhesion of the
gasket materials and any tape used.
3. When installing near a furnace or heating coils, run
the heating system through five full heating cycles
to ensure the temperature of the ActivePure
Induct Guardian I unit does not exceed 200 ˚F.
4. An approximate 3.5” (8.89 cm) opening will need to
be cut into the existing ductwork to install the unit
properly.
5. Aer a few minutes, adjust the control to the desired speed.
NOTE: Unit requires power 24/7. Do not install where power to the unit will be cycled on and o.
Min. 9” x 9” Metal
Ductwork
Min. 10” x 10”
Fiberglass
Ductwork
Air Handle
Max.
15 .
Installation Clearance

7
For 120V Domestic Units: Black = L1, White = Neutral, Green = Ground
For 220V Commercial Units: Black = L1, White = L2, Green = Ground
For 230V International Units: Brown = L1, Blue = L2, Green w/yellow stripe = Ground
ELECTRICAL REQUIREMENTS
• Wiring of the unit into your HVAC system should be done by a
licensed HVAC installer or electrical contractor only
• This unit is equipped with a universal ballast that operates at
nominal voltages between 100 and 240 VAC, 50/60 Hz
CAUTION
To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations. This equipment emits UV-C radiation. DO NOT locate
equipment in any location allowing direct line-of-sight to vents, returns,
or other duct openings. Disconnect from supply before servicing or
replacing.
WARNING
INSTALLING THE UNIT
CAUTION
• Hard wiring unit into HVAC system must be done by a licensed HVAC
installer or electrical contractor only
• When the unit is installed in a roof mounted HVAC system, the unit
must be protected from elements
• Unit requires power 24/7; DO NOT install where power to the unit will
be cycled on and o
To Reduce the Risk of Electric Shock – DO NOT use in wet or damp
locations. This equipment emits UV-C radiation. DO NOT locate
equipment in any location allowing direct line-of-sight to vents, returns,
or other duct openings. Disconnect from supply before servicing or
replacing.
WARNING
Find the optimal position downstream from the air handler. Ensure location in duct has enough room for
the mounting plate. It is recommended for maximum eectiveness that the unit be placed as close to the
air handler as possible.
1. Locate suitable
area of duct for
installation.
2. Cut away insulation to
expose metal duct
(if needed).
3. Mark location for
3.5" opening using the
mounting plate.
4. Cut hole in
duct using
3.5" hole saw.

8
INSTALLING THE UNIT CONT.
1/4
5. Remove backing from
mounting plate adhesive
gasket.
6. Center openings and press
mounting plate onto duct. The
adhesive gasket will hold the
mounting plate in place.
7. Secure the mounting plate
using eight #8 self-tapping
screws.
8. Insert unit into opening. Be
sure the air will pass though
the ActivePure®Cell honey-
comb matrix.
9. Secure the unit to the
mounting plate with four
thumb nuts.
NOTE: Unit requires power 24/7. Do not install where power to the unit will be cycled on and o.
a. Using the mounting plate,
mark four cuing method
holes on duct.
b. Drill four holes where
marked.
c. Cut between holes
using tin snips.
ALTERNATE CUTTING METHOD:

9
Your ActivePure®Induct Guardian I unit requires no periodic maintenance
beyond normal replacement of the ActivePure Cell every one (1) year.
The UV bulb operation indicator on the face of the unit will glow when the
UV bulb is in use. If the indicator does not glow and the unit has power, the
ActivePure Cell should be replaced.
C
MAINTENANCE / UV BULB INDICATOR
UV Bulb Indicator
NOTE: For optimal performance and to maintain the limited 5 year warranty, it is required to replace the
ActivePure®Cell once every year, even if the UV bulb appears to be operating normally.
2. Connect the unit to the load side of the proper fan relay.
4. Check indicator light for proper operation with fan on.
1. Connect wires coming from the ActivePure®Induct Guardian I unit as follows:
NOTE: All units come standard with a blunt cord.
120 Volt Unit:
Black Wire L1
White Wire Neutral
Green Wire Ground
220 Volt Unit:
Black Wire L1
White Wire L2
Green Wire Ground
International Unit:
Brown Wire L1
Blue Wire L2
Green with
Yellow Stripe Ground
Disconnect power at the breaker or fuse panel before servicing unit.
Always follow OSHA lockout procedures to prevent accidental exposure
to electrical energy.
WARNING
3. Be sure to ground the ballast by securing the unit to the metal surface
of the AC unit or power box.
Hard wiring unit into HVAC system should be done by a licensed HVAC
installer or qualified electrical contractor only.
CAUTION
WIRING THE UNIT

10
CHANGING THE ACTIVEPURE CELL
• UV Light in operation; disconnect unit from power cord before
servicing; failure to follow warnings may result in severe eye damage
• Disconnect power at the breaker or fuse panel before
servicing unit; always follow OSHA lockout procedures to prevent
accidental exposure to electrical energy
WARNING
1. Disconnect (unplug)
power cord from unit.
2. Remove the four thumb
nuts.
3. Remove the unit from the
mounting plate.
Power Cord
4. Remove the two thumb
screws holding the
ActivePure Cell.
5. Remove the used
ActivePure Cell from the base
unit and dispose of the bulb
properly.
6. Plug the new ActivePure Cell
into the base unit. Be sure
Air Flow / Honeycomb Cell
direction is correct.
7. Secure with two
thumb screws
8. Insert the unit into
the mounting plate.
9. Secure unit with
four thumb nuts.
10. Reconnect power
cord.
Power Cord
Visit www.lamprecycle.org for proper bulb disposal regulations
NOTE: Always follow OHSA electrical lockout safety requirements to prevent accidental
release of energy during service or maintenance activities.

11
REPLACING THE BALLAST
• UV Light in operation; disconnect unit from power cord before
servicing; failure to follow warnings may result in severe eye damage
• Disconnect power at the breaker or fuse panel before
servicing unit; always follow OSHA lockout procedures to prevent
accidental exposure to electrical energy
WARNING
1. Disconnect (unplug)
power cord from unit.
2. Open the ballast housing by
removing the four screws, then
remove the cover.
3. Disconnect all ballast
wiring by pressing down on
connector tabs and pulling
wire straight out.
Power Cord
C
4. Remove the two nuts
securing ballast to the case.
Remove the ballast.
5. Place new ballast into the
original location and secure
using the two nuts removed in
step 4.
6. To reconnect wiring, insert
wire into wire pocket in
ballast until boomed.
Gently pull wire to ensure it
is properly connected.
C
7. Replace cover and secure
with the original four screws.
8. Re-install unit if removed from duct.
Reconnect power cord, turn breaker
or fuse power back on and check for
proper operation.
C
UV Bulb
Indicator
NOTE: UV Lamp Indicator should be lit when in operation.

12
TROUBLESHOOTING
CAUTION
This unit must be installed and serviced by a licensed HVAC contractor
or electrician. Failure to do so will void the warrant of the product.
• UV Light in operation; disconnect unit from power cord before
servicing; failure to follow warnings may result in severe eye damage
• Live voltage may be present
• Disconnect power at the breaker or fuse panel before servicing
unit; always follow OSHA lockout procedures to prevent accidental
exposure to electrical energy
WARNING
1. Check the incoming voltage by unplugging the power cord from the side of the ActivePure®Induct
Guardian I and placing one probe on the outside of the plug and the other on the inside of the plug.
Voltage measurement should read 18 – 32 VAC. If no voltage is present, replace the transformer
supplying power to the ActivePure Induct Guardian I.
2. Leave unit aached to ducting. Remove four (4) Phillips head screws from the cover of the unit.
Remove the cover. Unplug the black and white wires from the ballast. Check incoming voltage by
placing Multimeter probes on the two exposed wires. Voltage measurement should be between 18
– 32 VAC. If there is no voltage reading, power is not supplied to the unit. Check power source and
verify Induct Safety Switch is fully depressed. Safety switch plunger is located underneath the unit
and is depressed when unit is secured to mounting plate.
3. Re-plug the black and white wires to the ballast.
4. Remove unit from the duct by taking o the four (4) 11/32 thumb
nuts that secure the unit to the mounting plate.
5. Remove the two (2) Phillips head screws that hold the cell
assembly in place. Remove the UV bulb from the 4-pin connector
by placing a small flat head screwdriver between the 4-pin
connector and the UV bulb base. Gently pry and li up on the Cell
until the UV bulb is unseated from the 4-pin connector, remove
the Cell Assembly.
6. Check the continuity of the UV bulb filaments with a Multimeter by placing the Multimeter probes on
the UV bulb pins that are closest to each other. The Multimeter should beep if the filaments are not
broken. Resistance can also be checked if continuity is not available on the Multimeter. Resistance
should be between 3 – 5 ohms. If continuity or resistance check is bad, replace the ActivePure®Cell.
7. If continuity or resistance check is good, replace the ballast. To replace the ballast follow the steps
listed on pages 11 and 12.
Test Continuity
or Resistance
at each set of 2
closest Pin
Test Continuity
or Resistance
at each set of 2
closest Pin
Tools Required:
• 1/4 Nut Driver
• Phillips Head
Screwdriver
• Multimeter
• Small Flat Head
Screwdriver
• Flashlight

13
Limited Five (5) Year Warranty
To register your ActivePure®Induct Guardian I unit, visit www.activepure.com/warranty.
To view full details on warranty coverage, visit www.activepure.com/manuals.
WARRANTY INFORMATION
If you have any questions concerning this, or any ActivePure product,
contact ActivePure Customer Service at 800.572.1446 or email
[e-mail].
REPLACEMENT PARTS QTY PART NUMBER
ActivePure®Cell (Includes UV Bulb) 9950231
Ballast 9950102
Power Cord 9950103
To order replacement parts, contact your sales representative or ActivePure
Customer Service for further assistance at 800.572.1446 or email
[e-mail].
REPLACEMENT PARTS  SERVICE

FCC Declaration of Conformity
Name: ActivePure®Induct Guardian I
Model: B1013U
Produced by: ActivePure Manufacturing, LLC
This device complies with Part 15 of the
FCC Rules.
Responsible Party
ActivePure Manufacturing, LLC
1300 Valley Drive
Bristol, VA 24201
Ph: 800.572.1446
Signature:
Printed Name: Andrew Eide
Title: Vice President of Product Development
and Manufacturing
Date: 01/10/22
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant of
part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy, and if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the Independent Contractor
for help.
FCC DECLARATION  RESPONSIBLE PARTY

15

16
For information regarding the use of this product, please call Customer Service.
1.800.572.1446 or email at customerser[email protected]
www.activepure.com
™
ActivePure Manufacturing, LLC | 1300 Valley Drive | Bristol, VA 24201 | 800.572.1446
Assembled in U.S.A. | © ActivePure Manufacturing, LLC. All Rights Reserved AIG1_OM_65-00832_VA-01621E

C
™
E ATTENTIVEMENT LE MANUEL AFIN D’UTILISER
CORRECTEMENT L’APPAREILET D’ASSURER SON
FONCTIONNEMENT OPTIMAL.

18
INFORMATIONS GÉNÉRALES
Si vous avez des questions concernant cet appareil ou un autre produit ActivePure,
contactez le service à la clientèle ActivePure au 1-800-572-1446, ou par courriel à
l’adresse [email protected].
TABLE DES MATIÈRES
Description du produit . . . . . . . . . . . 18
Spécifications. . . . . . . . . . . . . . . 18
Stockage et mise au rebut . . . . . . . . . . 18
Consignes de sécurité importantes . . . . . . 19
Pour les clients au Canada seulement . . . . . 20
Caractéristiques du produit . . . . . . . . . 21
Matériel d’installation (fourni). . . . . . . . . 21
Outils d’installation recommandés. . . . . . . 21
Exigences d’installation . . . . . . . . . . . 22
Installation électrique. . . . . . . . . . . . 23
Installation de l’appareil . . . . . . . . . . . 23
Branchement de l’appareil . . . . . . . . . . 25
Entretien/Indicateur lampe UV . . . . . . . . 25
Changement de la cellule ActivePure®. . . . . 26
Remplacement du ballast . . . . . . . . . . 27
Dépannage . . . . . . . . . . . . . . . . 28
Pièces de rechange et service . . . . . . . . 29
Informations relatives à la garantie . . . . . . 29
Déclaration FCC et partie responsable . . . . . 31
DESCRIPTION DU PRODUIT
Félicitations pour votre achat de l’ActivePure®Induct Guardian I! L’unité se monte facilement
sur le côté alimentation des conduits d’air d’un système de climatisation et de chauage, par un
électricien ou un professionnel du CVC, afin d’assurer une désinfection des surfaces et de l’air
24 h/24 et 7 j/7. Veuillez lire et suivre toutes les procédures d’entretien décrites dans le présent
manuel.
STOCKAGE ET MISE AU REBUT
Ne pas jeter ce produit avec les ordures
ménagères. Les déchets électriques et les
produits électroniques doivent être recyclés de
manière appropriée, conformément aux
pratiques établies par les autorités locales.
SPÉCIFICATIONS
ActivePure Induct Guardian I
• Numéro de modèle: B1013U
• Numéro de série: 00761
Données électriques:
• Tension d’alimentation: 24 Vca; ~ 50/60Hz
• Courant: 1,0 A
• Consommation: 17 W
• Conforme à la norme UL 1598
Mécanique:
• Distribution par une unité de traitement
de l’air avec interrupteur de sécurité
Poids et dimensions:
• 3 lbs (1,36 kg)
• H 8,5 po x L 8,5 po x P 11 po
(21,59 cm x 21,59 cm x 27,94 cm)
Température de fonctionnement:
• 34 à 200 ºF (1 à 93 °C)
Couverture maximale recommandée
dans un espace étroit1:
• Chaque lieu est unique et une bonne
configuration est aussi importante que la
technologie. Pour approuver la couverture
dans votre bâtiment, consultez votre
représentant commercial ou contactez le
service à la clientèle au 1.800.572.1446.
Garantie:
• Garantie limitée de cinq (5) ans
ActivePure®Manfufacturing, LLC se réserve le droit
de modifier des spécifications sans préavis.
1. Pour un plafond de 8 pieds. Les solutions doivent être
adaptées en fonction de diérents facteurs, notamment la
capacité et les réglages du système CVC, les débits d’air (en
tenant compte des murs, de la pression atmosphérique et
des portes), la température et l’humidité de l’air ambiant, les
variations de densité, les concentrations de COV connues
et les autres couches de protection.

19
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES CONSIGNES
• Lampe UV en marche; débrancher l’appareil de l’alimentation
électrique avant l’entretien; le non-respect de cet avertissement peut
entraîner de graves lésions oculaires et/ou une décharge électrique
• Pour éviter d’endommager l’appareil, la température de
l’environnement d’utilisation ne doit jamais dépasser 200 oF (93 oC)
• Cet appareil NE DOIT JAMAIS être utilisé avec une rallonge électrique
• •Afin de réduire les risques de décharge électrique, cee unité peut
posséder une fiche de courant avec mise à la terre avec une troisième
broche (de mise à la terre); Cee fiche ne s’insère que dans une
prise de courant avec mise à la terre; si la fiche ne s’insère pas dans
la prise, demandez à un professionnel qualifié d’installer une prise
adéquate; NE PAS modifier la fiche de quelque manière que ce soit
• Cet appareil est équipé d’un ballast universel fonctionnant avec une
tension nominale comprise entre 100 et 240 VCA, 50/60 Hz
• Afin de réduire les risques de décharge électrique, NE PAS
utiliser dans des lieux mouillés ou humides. Cet appareil émet un
rayonnement UVC; NE PAS placer l’unité dans des lieux permeant
une exposition directe aux ventilations, retours ou autres bouches
d’aération
• NE JAMAIS brancher cet appareil à une source de tension supérieure
à 32 volts, au risque de l’endommager
MISE EN
GARDE
Emplacement de la mise à la terre.
ATTENTION
• L’appareil doit être installé par un fournisseur ou un électricien agréé
en CVC; la garantie du produit sera annulée en cas de non-respect de
cee condition
• Si l’appareil est installé dans un système CVC fixé sur un toit, il doit
être protégé des éléments
Veuillez lire ce manuel dans son intégralité avant d’utiliser votre appareil ActivePure® Induct Guardian I.
Garder hors de la portée des enfants.
• Présence possible de tension
• Exigences de raccordement électrique: Cet appareil est conçu pour fonctionner sur un transformateur
standard de 24 VCA, 40 VA. Le transformateur fourni avec un système de climatisation ou CVC standard peut
être utilisé pour alimenter l’appareil, mais sa capacité à supporter la charge supplémentaire de l’appareil doit
être confirmée avant l’installation. Si la capacité du transformateur existant est insuisante pour la charge
supplémentaire, il est OBLIGATOIRE d’utiliser un transformateur séparé de 24 VCA et 40 VA. Ne pas brancher
l’appareil à une source d’alimentation dont la tension nominale est inférieure à 22 VCA ou supérieure à 32 VCA.
L’appareil risquerait de subir des dommages.
• Couper l’alimentation au niveau du disjoncteur ou du panneau de fusibles avant de procéder à l’entretien de
l’appareil; toujours suivre les procédures de verrouillage OSHA afin de prévenir toute exposition accidentelle à
un circuit électrique sous tension
• En cas d’installation près d’un appareil de chauage central ou à un endroit où des serpentins chauants
pourraient augmenter la température de la chambre de distribution, faites fonctionner l’unité d’air conditionné
pendant trois cycles de chauage complets en vous assurant que la température ne dépasse jamais 200 °F
(93 °C); la cellule ActivePure®ne doit pas dépasser 200 °F (93 °C).
• Si l’appareil est branché par un câble, assurez-vous que l’alimentation de l’appareil est coupée; suivez toujours
les procédures de verrouillage OHSA afin de prévenir une fuite accidentelle d’énergie durant l’entretien.
• N’essayez jamais de vérifier le fonctionnement des cellules ActivePure®par observation directe, cela peut
provoquer des dommages oculaires graves. Utilisez uniquement les indicateurs de lampe UV en bas du ballast.

20
POUR LES CLIENTS AU CANADA SEULEMENT
ACTIVEPURE®INDUCT GUARDIAN I
Numéro de série: 00761
Ce modèle à rayons UV permet de réduire la propagation des virus dans l’air.
Garder hors de la portée des enfants.
Veuillez lire l’étiquee et le guide d’utilisation avant de commencer à utiliser le produit:
www.activepure.com/manuals
PRÉCAUTIONS:
MISE EN GARDE: Cet appareil émet des rayonnements UV. L’utilisation involontaire de cet
appareil ou un boîtier endommagé peut entraîner l’exposition à des rayons ultraviolets. Les
rayonnements ultraviolets peuvent irriter les yeux et la peau. Évitez d’exposer vos yeux et votre
peau aux rayons ultraviolets.
INSTRUCTIONS POUR LES PREMIERS SOINS: Veuillez contacter votre professionnel de la
santé en cas de blessure causée par cet appareil.
MODE D’EMPLOI:
L’appareil doit être installé en aval de l’unité de traitement de l’air dans le système CVC par un
fournisseur ou électricien agréé en CVC. Veuillez consulter le manuel d’utilisation pour obtenir
des instructions détaillées concernant l’utilisation, la manipulation, le stockage et la mise au
rebut de l’appareil, ainsi que les procédures à suivre pour réduire les risques associés.
L’utilisation de cet appareil agit en complément des pratiques standards de contrôle des
infections et ne représente donc pas un moyen de substitution à celles-ci. Les utilisateurs
doivent continuer à suivre toutes les pratiques standards actuelles en matière de contrôle
des infections, y compris celles concernant le neoyage et la désinfection des surfaces
environnantes.
POUR TOUTE QUESTION, VEUILLEZ CONTACTER:
AERUS CANADA, INC.
Laird Business Park
3480 Laird Road, Unités 2 – 5
Mississauga, Ontario, Canada, L5L 5Y4
W. Parrell, Responsable
[phone]
wparrell@aerusonline .com
Aerus Canada, Inc. est ailiée à ActivePure Manufacturing, LLC
1300 Valley Drive, Bristol, VA 24201, États-Unis.