ActronAir PKV290T-T User manual

IMPORTANT NOTE:
Please read this manual carefully before installing or operating your air conditioning unit.
That’s better. That’s Actron.
Variable Capacity Commercial
Package Ducted Units
Installation and Commissioning Guide
PACKAGE MODELS
UNDER/OVER
CONFIGURATION
SIDE BY SIDE
CONFIGURATION*
PKV290T-T
PKV330T-T
PKV290T-L/R
PKV330T-L/R
*Left Air Handing Option shown for illustration purposes only.
Left Air Handing Option.
Right Air Handing Option.

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
2Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Table of Contents
01. Inspections................................................................................................................................. 3
02. General Information ................................................................................................................... 3
03. Safety Instructions .....................................................................................................................4
04. Installation Information.............................................................................................................. 5
05. Wall Control Operation Manual Access ....................................................................................... 6
06. Components Overview ............................................................................................................... 7
07. Package Unit Dimensions / Clearances........................................................................................ 9
. Package Model : PKVT-T / PKVT-T 
. Package Model : PKVT-L/PKVT-L 
. Package Model : PKVT-R / PKVT-R 
08. Unit Lifting Procedure ............................................................................................................... 15
09. Outdoor Unit Preparation .......................................................................................................... 17
10. Condensate and Safety Tray Drainage Instructions ....................................................................19
11. Electrical Installation................................................................................................................ 20
12. Package Unit Electrical Connection............................................................................................ 21
13. Maximum Cable Length ............................................................................................................ 22
. Wall Controller Options 
. Wiring Configuration  : Recommended 
. Wiring Configuration  : Alternate 
14. Wiring Connections ..................................................................................................................25
. LC- Wall Control Wiring Connections 
. NEO Wall Control Wiring Connections 
. LM-RS- Optional Sensor Wiring Connections 
. AERSS Optional Duct Sensor Wiring Connections 
15. Configuring and Commissioning Setup ......................................................................................27
. Menu and Navigation 
. Configuring Compressor and Capacity (cnFg) 
. Configuring Control Source (CtrS) 
. Configuring Indoor Fan Setting (iduS) 
16. Optional Output/Input Relay.................................................................................................... 36
. Filter Indication Relay Output (CMI Board) 
. Fan Run Indication Output (CMI Board) 
. Optional Outside Air Damper Control Output (CMI Board) 
. Third Party Control Input (CMI Board and/or Outdoor) 
. Demand Response Management (Outdoor Board) 
. Run and Fault Indication Output (Outdoor Board) 
. Remote ON/OFF 
17. Indoor Fan Table And Fan Curve ................................................................................................ 42
. PKVT-T 
. PKVT-T 
. PKVT-L/R 
. PKVT-L/R 
18. Refrigerant Charging ................................................................................................................ 50
19. Maintenance Procedures ...........................................................................................................53
20. Maintenance Frequency Checklist..............................................................................................55
21. Start Up and Commissioning Report ..........................................................................................57

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
3
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
01. Inspections
Information About This Guide
This guide provides installation instructions, specific to your package unit. Read this manual thoroughly and take into
consideration all specifications and instructions to ensure correct installation and safe operation of your air conditioning
system.
NOTE
Keep this document for future reference. Ensure all technicians that work on the unit can refer to this manual at any time.
Product Inspections
Check your air conditioning unit and all items against the invoice upon receiving your shipment. Inspect the unit,
components and accessories for any sign of damage. If there is any damage to the unit, contact ActronAir Customer Care
Department immediately on: 1300 522 722 to obtain a Goods Return Number.
Check the unit nameplate to verify the model, serial number and electrical rated specifications.
Codes, Regulations and Standards
The installer and/or contractor assumes responsibility to ensure that unit installation complies with the relevant council,
state / federal codes, regulations and building code standards. All electrical wiring must be in accordance with current
electrical authority regulations and all wiring connections to be as per electrical diagram provided with the unit.
02.General Information
The ActronAir Variable Capacity air conditioning units are designed for applications where superior performance, high
efficiency, reliability, supply air quality and quiet operation are the prime priorities. The units are built with the latest
technology, advanced variable speed driven compressor, EC indoor fans (on specific models), low-noise outdoor fans and
an intelligent electronic control.
For optimum efficiency, your air conditioning unit will deliver the right amount of cooling or heating capacity that you
demand. Even in extreme conditions, the unit will still supply the required demand at peak performance.
Energy Efficient Refrigeration Circuits
The ActronAir Variable Capacity system is designed with a highly efficient refrigeration circuit that delivers only the amount
of cooling or heating actually required to maintain your desired comfort at the most optimum efficiency.
The refrigeration circuit consists of:
• High efficiency variable capacity scroll compressor.
• Hydrophilic coated condenser coil designed for optimum performance and efficiency with corrugated fins and
riffled tubing.
• Hydrophilic coated evaporator coil designed for optimum performance and efficiency with lanced fins and riffled
tubing.
• Electronic expansion valve (EEV), to maintain efficiency at different operating conditions.
Evaporator Section
The evaporator section has EC fans which deliver the right amount of airflow, depending on requirements. The fans provide
superior performance for your comfort at optimum efficiency:
• Highly efficient variable speed EC motor that uses less energy than the traditional AC motor.
• Easy indoor fan commissioning via intelligent controllers.
• Low noise operation
Condenser Section
Uses multiple speed outdoor fans and a state of the art digital scroll compressor, with the following features:
• Highly efficient axial fans with direct drive AC motor.
• Variable compressor capacity (20% - 100%).
• Low noise operation

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
4Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Electrical Section
The electrical section consists of:
•EMC filters
•Switchgears
•3 Phase motor protection
•7 Segment Display menu and fault code
•Adjustable indoor airflow pot
•Optional soft start, BMS card, ActronAir Group Control
Durable Design and Construction
ActronAir is an Australian manufacturer with proven high quality air conditioning products. Known for their durability and
reliable performance, these products are designed and built to withstand the extreme weather conditions.
The galvanized steel cabinet, with powder coated epoxy enamel finish, resists the toughest conditions. The louvered
outdoor coil guard protects the condenser from any potential damage brought by hail, stones and other solid objects that
may be projected to the unit.
Blue Hydrophilic coil fins provide protection to your heat exchangers and enhanced heat transfer with increased
performance efficiency.
System Flexibility
The ActronAir Variable Capacity range air conditioning units is the first choice for residential and commercial applications,
both for new construction or retrofitting projects.
Refrigerant Handling and Accountability
ActronAir strongly urges that all service technicians make every effort possible to reduce the emission of refrigerants to
the atmosphere. Everyone must act in a responsible manner to conserve refrigerants in accordance to the industry code of
practice.
03. Safety Instructions
•Only licensed HVAC technicians* should install and service this air conditioning equipment. Improper service or alteration
by an unqualified technician could result in significant and major damage to the product or property which may render
your warranty null and void. Such unqualified service could also lead to severe physical injury or death. Follow all safety
instructions in this literature and all warning labels that are attached to the equipment.
•Prevailing WH&S regulations must be observed and will take precedence to the safety instructions contained on this
manual. Safe work practices and environment must be the paramount importance in the performance of all the service
procedures.
•Ensure that unit installation complies with relevant council regulations and building code standards.
•All electrical wiring must be in accordance with current electrical authority regulations and all wiring connections to be as
per electrical diagram provided.
•Secure the fans against accidental contact. Beware of pinch point and sharp edges which can cause cutting injury.
•Always wear appropriate PPE, remove any dangling jewellery and protect long hair by wearing a cap.
•This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised
by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure
that they do not play with the appliance.
•Installer must incorporate a means of electrical disconnection (isolator) in the sub mains fixed wiring in accordance with
the latest edition of the AS/NZS 3000 (also known as Australian Wiring Rules).
•Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
*Qualifications required will be appropriate Electrical, Refrigeration and Refrigerant Handling License and Training
dependent on local State/Territory regulations.

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
5
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
DANGER
Hazardous Voltage - Risk of Electrocution.
TURN-OFF the power from main isolator before proceeding with any service work of the unit. Observe proper LOCK-OUT/TAG-
OUT (LOTO) procedures for electrical appliances in order to prevent accidental switching-on of the power supply.
WARNING
EC Motors are fitted with high power capacitors and can have dangerous residual voltages at motor terminals after power has
been isolated. Wait at least 5 minutes after power isolation and test for any residual voltage before beginning service work.
CAUTION
Beware of Rotating Fans !
Ensure that indoor and outdoor fans are isolated and have come to a complete stand still before servicing the equipment.
Beware of pinch point and sharp edges which can cause cutting injury. Secure the fans against accidental contact.
Always wear appropriate PPE and remove any dangling jewellery and protect long hair by wearing a cap. Ensure that no loose
clothing can be caught / entangled in moving parts.
VISUAL INSPECTION AND WORK ASSESSMENT
Work areas and conditions must first be assessed and evaluated for any potential hazardous conditions. It is also important to be
familiar with the unit parts and components before proceeding with any service task.
04.Installation Information
All service technicians handling refrigerant must be licensed to handle refrigerant gases.
Recover and Recycle Refrigerants
Never release refrigerant to the atmosphere! It is an offence in Australia to do so. Always recover, recycle and reuse
refrigerants. When removing from the system, properly contain and identify refrigerants in its dedicated container for
proper disposal and/or storage. Always consider the recycle or reclaim requirements of the refrigerant before beginning the
recovery procedures. Obtain a chemical analysis of the refrigerant if necessary. Refer recovered refrigerant and acceptable
refrigerant quality to existing standards and regulations.
Refrigerant Handling and Safety
Consult the refrigerant manufacturer’s safety data sheet (SDS) for information on proper handling and to fully understand
health, safety, storage and disposal requirements. Use the approved containment vessels and refer to appropriate safety
standards. Comply with all applicable transportation standards when shipping refrigerant containers.
Service Equipment and Recovery Procedures
Always use refrigerant reclaiming equipment in order to minimise refrigerant emissions. Use equipment and methods which
will pull the lowest possible system vacuum while recovering and condensing refrigerant. Equipment capable of pulling a
vacuum of less than 500 microns is required.
Do not open the system to the atmosphere for service work until refrigerant is fully removed and/or recovered. Perform
refrigeration system evacuation, prior to charging, in accordance with AIRAH / IRHACE Refrigerant handling code of
practice.
Let the unit stand for 1 hour and with the vacuum not rising above 500 microns. A rise above 500 microns indicates a leak
from the system and a leak test is required to locate and repair any leak.
CAUTION
A leak test is always required on any repaired section of the refrigeration system.

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
6Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Charge refrigerant into the system only after the equipment does not leak or contain moisture. Ensure that R-410A is only
charged in liquid form. Take into consideration the correct amount of refrigerant charge specified for the system to ensure
efficient unit operations. When charging is complete, reclaim refrigerant from charging lines into an approved refrigerant
container. Seal all used refrigerant containers with approved closure devices to prevent unused refrigerant from escaping
to the atmosphere. Take extra care to maintain all service equipment directly supporting refrigerant service work such as
gauges, hoses, vacuum pumps and recycling equipment.
INSTALLATION PREPARATION (Pre-installation considerations)
The following items must be considered before beginning the unit installation:
•Verify the unit capacities and ratings with the unit nameplate.
•Make certain the floor or foundation is level, solid and have sufficient structural strength to support the unit and
accessories weight.
•Preferably use anti-vibration rubber pads on residential units.
•Allow minimum recommended clearances for periodic maintenance and service access.
•Allow sufficient space above the unit for the outdoor air discharge. Condenser air inlet, located on the coil side of the
unit, requires sufficient airflow clearance for the optimum unit performance.
•Note the conditioned supply air and return air location. Ensure sufficient spaces are allocated for these purposes.
•Refer connection and location of condensate drain in the unit drawing and dimensions section of this manual.
•Wiring connections must be in accordance with the wiring diagram provided with the unit.
•Make sure all wirings are in accordance with local electricity authority regulations and standards.
•Do not install the unit close to an area where there is a danger of fire due to volatile, explosive, flammable and/or
hazardous materials.
•Ensure that spaces around the unit are free from any obstructions for optimum unit performance.
•Installer to ensure correct size/type that main circuit breaker and cable is installed in unit sub-mains to protect the sub-
mains and unit wiring.
•Installer to ensure correctly rated residual current device (RCD) is installed as per with the latest edition of the AS/NZS
3000 (also known as Australian Wiring Rules).
•Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
NOTES
• This unit is supplied with factory charged R-410A refrigerant.
• Be aware of all the relevant regulations concerning the handling of refrigerant.
05. Wall Control Operation Manual Access
Download from website
LC7-2
Operation Instruction can be downloaded through our website shown below.
https://www.actronair.com.au/brochures-manuals/#operating-manuals
NEO
Operation Instructions can be accessed through our website shown below.
http://neo.actronair.com.au/user-guide/

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
7
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
06.Components Overview
PACKAGE UNIT COMPONENTS OVERVIEW
Left Hand (LH) Side By Side Configuration shown for illustration purposes only
GRILLE PANEL
ACCESS EVAP
REAR PANEL
INDOOR
FANS
OUTDOOR
FANS
CONDENSER
COIL ASSEMBLY
ACCESS EVAP
FRONT PANEL
LP SWITCH
SCROLL
COMPRESSOR
CRANKCASE
HEATER
EVAPORATOR
COIL ASSEMBLY
ELECTRICAL
PANEL
HP SWITCH
ACCESS PANEL
COMP  ELECT
EEV ASSEMBLY

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
8Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
OUTDOOR UNIT ELECTRICAL PANEL OVERVIEW
FANSPEED
CAPACITORS
EARTHING BOLTS
WITH
WASHERS AND NUTS
OUTDOOR UNIT
CONTROL BOARD
CONDENSER MAINS INPUT
TERMINAL BLOCKS
PFC
CAPACITOR
CONTROL
CIRCUIT
BREAKER POWER FACTOR
CONTACTOR
FAN CIRCUIT
BREAKERS
CONDENSER
FAN
CONTACTORS
FIRE TRIP
TERMINAL BLOCKS
3 PHASE PROTECTION
RELAY
COMPRESSOR OVERLOAD
AND CONTACTOR
EMC FILTERS
CMI POWER
SUPPLY
CMI BOARD

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
9
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
07. Package Unit Dimensions / Clearances
07.01. Package Model : PKV290T-T / PKV330T-T
1420 O/A
187
150 1538 (MTG C-C DIST)
414
660
435
1840 O/A
1440 O/A
50
1179
1310
106
OUTDOOR COIL
COMP
CONDENSATE
DRAIN POINTS
DN 25mm PN12
35 1340 (MTG C-C DIST) 35
INDOOR
FANS
1098 284
1071453
283
934
547
INDOOR
FANS
150
OVERALL NOMINAL DIMENSION (H x W x L)
= 1420 x 1840 x 1440
SUPPLY DUCT (H x W) = 283 x 1098
RETURN DUCT (H x W) = 547 x 1453
DRAIN CONNECTION = DN 25mm PN12
NOTES:
1. Do not scale drawing. All dimensions
are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting
hole details.
2. Service Access Areas and Spaces for Airflow Clearances
given are suggested minimum based on the condition
that the spaces around the units are free from any
obstructions and a walkway passage of 1000mm between
the units or between the unit and the outside perimeter
is available.
3. Minimum service access areas and spaces for airflow
clearances are responsibilities of the installer, ActronAir
will not be held liable for any extra charges incurred due
to lack of access and space for airflow.
4. Under all circumstances, condenser air must not
recirculate back onto condenser coil. Keep all clearance
free of any obstructions.
5. STACKING OF UNITS: Ensure that minimum airflow and
clearances are met.
6. MTG C-C DIST = Mounting Centre to Centre Distance.
7. Use M12 bolt for feet mounting.
THIRD ANGLE
PROJECTION
TOP VIEW
FRONT VIEW SIDE VIEW

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
10 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Minimum Service Access Clearances and Airflow Space Allowances
OUTDOOR COIL
COMP
INDOOR
FANS
INDOOR
FANS
ID COIL
800 mm
SERVICE
CLEARANCE
COMPRESSOR
AND
ELECTRICAL
300 mm
SERVICE
CLEARANCE
AND
AIRFLOW
ALLOWANCE
DUCT
WORK
HEIGHT CLEARANCE = 1500 mm
750 mm
SERVICE CLEARANCE AND
AIRFLOW ALLOWANCE
D
B
A
C
YY
XX
CG
NOTE
• Under all circumstances, Condenser Air must not recirculate back onto Condenser Coil.
• Keep all clearances free of any obstructions.
Base Mounting Details
64
1840
64
1409
64
64
76
692
513
Unit Model
Number
Unit Weight
(Kg)
Corner Weights (Kg) Center of Gravity
A B C D XX YY
PKV290T-T 400 121 66 56 157 813 660
PKV330T-T 433 124 70 63 176 813 660

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
11
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
07.02. Package Model : PKV290T-L/PKV330T-L
L - left Hand Air Handing Configuration
1420 O/A
82753
1135368
328
788
187
1072
150 1540 (MTG C-C DIST) 150
414660
435
1840 O/A
1440 O/A
50
1179
1310
106
OUTDOOR COIL
COMP
35 1340 (MTG C-C DIST) 35
INDOOR COIL
INDOOR
FANS
CONDENSATE
DRAIN POINTS
DN 25mm PN12
OVERALL NOMINAL DIMENSION (H x W x L)
= 1420 x 1840 x 1440
SUPPLY DUCT (H x W) = 788 x 368
RETURN DUCT (H x W) = 1072 x 753
DRAIN CONNECTION = DN 25mm PN12
NOTES:
1. Do not scale drawing. All dimensions
are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting
hole details.
2. Service Access Areas and Spaces for Airflow Clearances
given are suggested minimum based on the condition
that the spaces around the units are free from any
obstructions and a walkway passage of 1000mm between
the units or between the unit and the outside perimeter
is available.
3. Minimum service access areas and spaces for airflow
clearances are responsibilities of the installer, ActronAir
will not be held liable for any extra charges incurred due
to lack of access and space for airflow.
4. Under all circumstances, condenser air must not
recirculate back onto condenser coil. Keep all clearance
free of any obstructions.
5. STACKING OF UNITS: Ensure that minimum airflow and
clearances are met.
6. MTG C-C DIST = Mounting Centre to Centre Distance.
7. Use M12 bolt for feet mounting.
THIRD ANGLE
PROJECTION
TOP VIEW
FRONT VIEW SIDE VIEW

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
12 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Minimum Service Access Clearances and Airflow Space Allowances
800 mm
SERVICE
CLEARANCE
COMPRESSOR
AND
ELECTRICAL
300 mm
SERVICE
CLEARANCE
AND
AIRFLOW
ALLOWANCE
DUCT
WORK
HEIGHT CLEARANCE = 1500 mm
750 mm
SERVICE CLEARANCE AND
AIRFLOW ALLOWANCE
D
B
A
C
OUTDOOR COIL
COMP
INDOOR COIL
INDOOR
FANS
YY
XX
CG
NOTE
• Under all circumstances, Condenser Air must not recirculate back onto Condenser Coil.
• Keep all clearances free of any obstructions.
Base Mounting Details
64
1840
64
1409
64
64
76
692
513
Unit Model
Number
Unit Weight
(Kg)
Corner Weights (Kg) Center of Gravity
A B C D XX YY
PKV290T-L 399 116 70 56 157 813 660
PKV330T-L 432 120 73 63 176 813 660

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
13
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
07.03. Package Model : PKV290T-R / PKV330T-R
R - Right Hand Air Handing Configuration
1840 O/A
414
435
1440 O/A
788
328
753233
1072
187
150 1540 MTG C-C DIST 150
1310 1179
50
35 1340 (MTG C-C DIST) 35
106
INDOOR
FANS
INDOOR COIL
OUTDOOR COIL
COMP
660
CONDENSATE
DRAIN POINTS
DN 25mm PN12
368
1420 O/A
OVERALL NOMINAL DIMENSION (H x W x L)
= 1420 x 1840 x 1440
SUPPLY DUCT (H x W) = 788 x 368
RETURN DUCT (H x W) = 1072 x 753
DRAIN CONNECTION = DN 25mm PN12
NOTES:
1. Do not scale drawing. All dimensions
are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting
hole details.
2. Service Access Areas and Spaces for Airflow Clearances
given are suggested minimum based on the condition
that the spaces around the units are free from any
obstructions and a walkway passage of 1000mm between
the units or between the unit and the outside perimeter
is available.
3. Minimum service access areas and spaces for airflow
clearances are responsibilities of the installer, ActronAir
will not be held liable for any extra charges incurred due
to lack of access and space for airflow.
4. Under all circumstances, condenser air must not
recirculate back onto condenser coil. Keep all clearance
free of any obstructions.
5. STACKING OF UNITS: Ensure that minimum airflow and
clearances are met.
6. MTG C-C DIST = Mounting Centre to Centre Distance.
7. Use M12 bolt for feet mounting.
THIRD ANGLE
PROJECTION
TOP VIEW
FRONT VIEW SIDE VIEW
done

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
14 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Minimum Service Access Clearances and Airflow Space Allowances
800 mm
SERVICE
CLEARANCE
COMPRESSOR
AND
ELECTRICAL
300 mm
SERVICE
CLEARANCE
AND
AIRFLOW
ALLOWANCE
DUCT
WORK
HEIGHT CLEARANCE = 1500 mm
750 mm
SERVICE CLEARANCE AND
AIRFLOW ALLOWANCE
D
B
A
C
INDOOR
FANS
INDOOR COIL
OUTDOOR COIL
COMP
YY
XX
CG
NOTE
• Under all circumstances, Condenser Air must not recirculate back onto Condenser Coil.
• Keep all clearances free of any obstructions.
Base Mounting Details
64
1840
64
1409
64
64
76
692
513
Unit Model
Number
Unit Weight
(Kg)
Corner Weights (Kg) Center of Gravity
A B C D XX YY
PKV290T-R 399 70 116 56 157 813 660
PKV330T-R 432 73 120 63 176 813 660

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
15
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
08.Unit Lifting Procedure
WARNING
WH&S regulations must be observed and will take precedence during lifting process.
Crane Lifting Method
Note: Crane lifting method is recommended for high rise lifting.
Fig. 1
Connect the loop ends
of slings into shackle
Provide rubber pads
to prevent damage
to the unit
RUBBER
PADS
LIFTING POINT
Lifting point is located at each corner of
the unit (4 Total). Size: Ø17.5 mm
EQUIPMENT REQUIRED FOR CRANE LIFTING:
•1 x Shackle
•2 x Nylon Slings
•Spreader Bar
NOTE
Refer to Unit Dimensions and Clearances section for unit weight before selecting shackles and slings.

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
16 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Procedure:
1. Remove all screws and washers that secure the unit to the timber pallet.
2. Use 4 x Bow or Dee shackle to connect the lifting holes.
3. Slip nylon slings through all shackles.
4. Ensure slings are protected by rubber pads or similar if slings are draped across the unit edges and corners. This will pre-
vent the unit from being damaged during lifting.
5. SPREADER BAR must be used when lifting the unit.
DANGER
Make sure rigging equipment, accessories and plant are sufficiently and safely capable to lift the unit in order to prevent
potential damage to property, severe personal injury or death. Check unit weight and weight distribution points on unit
drawing dimensions section.
NOTES
• Lifting procedure and unit model shown are suggestions and for illustration purposes only.
• It is highly recommended that installer observe current industry safe and sound rigging and lifting procedure.
CAUTION
Length of fork lift tines must pass the unit middle section, in order to safely carry the unit.
Fork Lift Method
Procedure:
. To move the unit around with a forklift, insert the fork tines through the unit feet assembly, as shown in Fig. .
. Only fork the unit through compressor end or side of the unit.
(See illustration for location of compressor end)
CAUTION
DO NOT LIFT from this end
Fig. 2
COMPRESSOR
END
Insert forklift tines
here

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
17
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
09. Outdoor Unit Preparation
NOTE
It is important to remove the shipping blocks before unit operation.
Step 1. Remove Access Panel, as shown below:
Access Panel
Use allen keys to remove the
Access Panel Hex Recess (8mm)
Remove access panel. Do not disconnect Earth Cable.
B
Removal Order:
Pull-Out 20mm
Pull-Down to remove
Access Panel-Electrical
A
B
A
Earth
Cable
Remove
Access Panel

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
18 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
Step 2. Remove Shipping Blocks.
Loosen the set bolts that hold the compressors down
onto the unit (4 pcs) Slide out shipping block as shown below.
Loosen Bolts (4-pcs / Comp.)
Shipping Blocks
GENTLY Push back the
Compressor
Pull away the
Shipping Blocks
Step 3. Tighten back the set bolts that hold the compressors down onto the unit (4 pcs)
Tighten Bolts
(4-pcs / Comp.)

Installation and Commissioning Guide Variable Capacity Commercial
PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
19
Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
10. Condensate and Safety Tray Drainage Instructions
OUTDOOR COIL
COMP
INDOOR
FANS
INDOOR
FANS
ID COIL
NOTES
• PKV Under and Over model shown for illustration
purposes only.
• Ensure that Condenser and Evaporator condensate
drains are connected separately.
SUGGESTED DRAIN TRAP DETAILS
Ensure Drain Pipe slopes down
from the unit at a minimum of
10mm per meter
DETAIL A
The top of the Trap must
be 125mm below the top
of the Evaporator Drain
Connection
50mm
4 x PVC
Elbow
Install a T-Piece
as an Air Vent
for long drain runs
Hose
Clamps
Condensate Tray
The top of the Vent must be
50mm higher than the top of
the Evaporator Condensate
Tray
250mm or high enough
to
maintain positive Air Seal
Condensate Drain
Connection
DN 25mm PN12
Trap
Clear
Plastic
Inspection
Tube
125mm
TOP VIEW
FRONT VIEW AEnsure Condensate Drain Connection Drain Pipe slopes
down from the unit at a minimum of 10mm per meter.
Seal with
Silicon Sealant
Ensure Condensate Drain
Connection Drain Pipe slopes
down from the unit at a mini-
mum of 10mm per meter.

PRELIMINARY DATA ONLY Ver. 5.01 210406
THIS LABEL TO BE REMOVED ON SIGN-OFF
20 Installation and Commissioning Guide- Package Ducted Variable Capacity Commercial
Doc. Part No. 0525-067 Ver. 5 210414
Installation and Commissioning Guide Variable Capacity Commercial
11. Electrical Installation
All electrical work must be carried out by a qualified technician. Make sure all wiring is in accordance with local wiring rules.
Wiring connections should be made in accordance with the wiring diagram provided.
DANGER
Live Electrical Supply !
• During installation of your air conditioning unit, it may be necessary to work in close proximity to live electricity.
• Only qualified technicians are allowed to perform these tasks.
• Follow all electrical safety precautions when exposed to live electrical components.
Wiring Diagram
The wiring diagram specific for your air conditioning system is located on the inside panel of the control access door. Always
refer all wiring installation, servicing and troubleshooting of this equipment to this diagram to ensure correct electrical
connection are satisfied.
Supply Power Requirements and Procedures
It is the installer’s responsibility to provide power supply wiring to the unit’s Mains Power Supply terminal block. Make sure
all wirings are in accordance with local wiring rules. Wiring should conform to all current electrical authority regulations and
all wiring connections to be as per electrical diagram provided with the unit.
•Confirm that the power supply available is compatible with the unit nameplate ratings. The supply power must be within
+10% to -6% of the rated voltage as per AS60038.
•Protect electrical service from over current and short circuit conditions in accordance with the latest edition of the
AS/NZS 3000 “Australian / New Zealand Wiring Rules”. Size protection devices according to the electrical data of the unit.
•Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
•Provide the proper unit earthing in accordance with the local and national codes.
Compressor Voltage Balance Requirement
Check the voltage at the compressor terminals to determine if it is balanced. Voltage imbalance on three phase systemsCheck the voltage at the compressor terminals to determine if it is balanced. Voltage imbalance on three phase systems
can cause motor overheating and premature failure. The maximum allowable imbalance iscan cause motor overheating and premature failure. The maximum allowable imbalance is  2.0%, check the unit wiring2.0%, check the unit wiring
connections to locate and rectify the faults, should the voltage imbalance exceed this value.connections to locate and rectify the faults, should the voltage imbalance exceed this value.
NOTES
• Parts for the Condensate Trap are not supplied with the unit.
• Refer to Unit Drawing and Dimensions page of the Technical Selection Catalogue for specifications and details of drain
connectors.