Acuity Brands Lighting American Electric Lighting ATB0 Series User manual

INSTALLATION INSTRUCTIONS
ATB0 SERIES LUMINAIRES
American Electric Lighting a division of Acuity Brands Lighting
DRAWING NO. A72974 REV: A (FRONT) ©2014 ACUITY BRANDS LIGHTING, INC. ALL RIGHTS RESERVED. PART NUMBER 057-70-72974
WARN I N G
DISCONN ECT POWER BEFORE RELAMPI N G OR WI RI NG THE FI X T U RE.
READ ALL INST RU CT I ON S COMPLETELY BEFORE STARTI N G I N STALLATION
TO AVOID T HE RISK OF FIRE OR SHOCK, FI X T U RE MU ST BE IN STALLED IN COMPLI AN CE WI T H ALL APPLI CABLE NAT I ON AL
AN D LOCAL ELECT RI CAL/BUI LDI N G CODES. FOR CODE I NTERPRETAT ION , CONSU LT LOCAL CODE AU T H ORI TY
RISK OF FI RE. PRODUCT FOR OU TDOOR I N ST ALLAT ION AN D U SE ONLY .
WARN I N G
CAUTION
!
!
!
WARN IN G
EN SURE T HAT ALL POWER I S
DI SCON NECT ED PRI OR T O WI RIN G
!
MOUNTING / LEVELING:
DETERMINE THE SIZE OF THE MAST ARM. THIS LUMINAIRE IS
DESIGNED TO ACCOMMODATE A MAST ARM FROM 1/1/4" TO 2"
DIA. THE LUMINAIRE IS FACTORY SET TO MOUNT TO THE 1-1/4"
ARM. TO MOUNT TO A 2" ARM, A MODIFICATION MUST BE MADE.
THE REAR OPENING MUST BE ENLARGED. KNOCKOUTS ARE
CAST-IN AROUND THE REAR OPENING FOR THIS PURPOSE. TO
REMOVE THIS EXCESS MATERIAL, STRIKE WITH A HAMMER OR
GRASP WITH PLIERS AND BREAK OFF.
STANDARD MOUNTING:
LOOSEN (DO NOT REMOVE) THE FITTER BOLTS. LIFT THE
LUMINAIRE INTO POSITION IN FRONT OF THE MAST ARM SUCH
THAT THE MAST ARM ENTERS THROUGH THE OPENING AT THE
REAR OF THE LUMINAIRE AND BETWEEN THE FITTER BRACKET
AND THE LUMINAIRE HOUSING. TIGHTEN FITTER BOLTS
TO 10-12 FT-LBS.
CAU TION
OV ER-TORQU ING OF FI T T ER CLAM P BOLT S CAN
CREAT E CRACKS I N T HE HOU SI N G CAUSI NG
TH E FIX T U RE T O FALL T O T H E GROU N D.
!
WIRING:
PULL UP TERMINAL BLOCK COVER (OPTIONAL) AS SHOWN IN
THE PICTURE. FEED THE SUPPLY WIRES THROUGH THE MAST
ARM, DRESS THEM SO THEY DO NOT INTERFERE WITH ANY
COMPONENTS AND SO THEY WILL NOT BE PINCHED IN THE
DOOR, AND CONNECT THEM TO THE PROPER TERMINALS ON
THE TERMINAL BLOCK. VERIFY THE SUPPLY VOLTAGE IS
CORRECT AS NOTED ON THE NAMEPLATE LABEL. IF SUPPLIED,
PUSH DOWN THE TERMINAL BLOCK COVER TO KEEP
TERMINALS COVERED.
OPTIONAL PHOTOCONTROL:
PLUG THE PHOTOCONTROL INTO THE RECEPTACLE ENSURING
GASKET IS FIRMLY SEATED. TWIST CLOCKWISE UNTIL IT LOCKS INTO
POSITION.
IF PHOTOCONTROL RECEPTACLE ROTATION IS REQUIRED, LOOSEN
THE TWO PHILIPS HEAD RECEPTACLE SCREWS. ROTATE
RECEPTACLE, MAXIMUM OF 360° , THEN RE-TIGHTEN SCREWS
UNTIL SNUG, USING 20-25 IN-LBS OF TORQUE.
IF PHOTOCONTROL RECEPTACLE ROTATION IS REQUIRED FOR THE
P5 / P7 OPTION, LOOSEN THE TWO PHILIPS HEAD RECEPTACLE
SCREWS COMPLETELY. ROTATE RECEPTACLE 90°, 180°, OR 270°,
THEN RE-TIGHTEN SCREWS UNTIL SNUG, USING 20-25 IN-LBS OF
TORQUE.
NOTE:
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
5 YEAR LIMITED
WARRANTY
KNOCKOUT
WARN IN G
FI XT U RE M UST BE GROU N DED
TO FU N CT I ON AS I NT EN DED
!
TERMINAL
BLOCK COVER
TERMINA L
BLOCK
TERMINAL BLOCK:
RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.
WARN I N G
THI S I S AN ELCT RON I C DEV ICE AN D SH OU LD N OT BE LEFT EX POSED TO T HE ELEM EN T S
DU RI N G STORAGE, T RAN SPORTATI ON , OR I N STALLATION . I T IS RAT ED FOR OU TDOOR
USE ON CE PROPERLY IN STALLED AN D I N NORM AL CON DI TION .
!

REV DATE DESCRIPTION ECN BY APP
A03-JUN-2014 NEW RELEASE
PART NUMBER.
057-70-72974
DESCRIPTION DWG NUMBER
A72974
SHT 2 OF 2
INSTALLATION INSTRUCTIONS ATB0
017-3744
ALG MEJ