WE-EF ETC310-FS LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC310-FS LED
EVC310-FS LED
ETC319-FS LED
EVC319-FS LED
This product is factory-sealed.
Do not open during installation
Refer to the instructions contained in this
document for details.

25°C
1
IP67, Class I, ta ≤
Inground Luminaire
EVC310/319-FSETC310/319-FS
125
ø 120
5
125
ø 127

2
Light Source
LED
Maintenance
Apart from cleaning the outside of the luminaire, no special maintenance is necessary.
Damaged mains supply cable: Contact your authorised WE-EF agent for replacement.
Warning: Do not open luminaire while mains supply is switched on.

ETC310-FS, ETC319-FS, EVC310-FS, EVC319-FS:
No minimum distance.
3
Installation
The product must be installed and maintained by a
suitably qualified person in compliance with the latest
applicable regulations and relevant legislation.
Ensure the luminaire frame and lens are clear of dirt
and debris.
Claims based on defects attributable to improper
installation, application, operation and/or any modifi-
cation carried out by the purchaser or third parties,
and the consequences thereof, are excluded.
Installation Methods
Attention: The luminaire is factory-sealed and does
not need to be opened during installation.
For proper installation, use the supplied installation
blockout.
Ensure that proper drainage is provided for the shown
installation methods:
In landscape areas, sand with gravel base (Fig. I).
In paved areas, concrete with gravel base (Fig. II).
Fig. II
Fig. I
Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure a suitable recess is provided to accommo-
date installation blockout/mounting ring assembly
B/M.
2) Set installation blockout/mounting ring assembly
B/M in position and ensure that:
a) Arrow Ron mounting ring Mis pointed towards
the object to be illuminated (wall, tree, column).
b) Mounting ring Mis flush with surface F. If the
floor will be tiled or paved afterwards, leave an
appropriate gap.
c) Mains supply cable(s) Ois of sufficient length to
connect sealable junction box Jwith cable Efrom
luminaire.
3) During ongoing earth and/or masonry works, do
not remove stickers on fixing thread holes D.
Ensure that installation blockout/mounting ring
assembly B/M is not damaged and has maintained
its original shape.
Minimum Distance

cable in sealable junction box (or: two mains
sheet as provided with junction box.
termination details, refer to separate instruction
supply cables , if through wiring is required). For
mains supply
(from luminaire) and6) Terminate cable
4
Phase Two
Luminaire Installation and Electrical Connection
4) Switch off mains electrical supply.
5) Check that rating shown on luminaire label con-
forms with mains electrical supply.
E
J
7) Set cables and sealable junction box Jinside instal-
lation blockout/mounting ring assembly B/M.
8) Peel-off stickers on fixing thread holes D. Loosen
countersunk screws C (do not turn out). Insert
mounting lever Lbetween head of countersunk
screws C and cover lens. Place luminaire housing
Ainto installation blockout/mounting ring
assembly B/M(Fig. IV) while aligning holes Don
mounting ring M.
Warning: When luminaire is placed inside in-
stallation blockout B, ensure there is no stress on
sealable junction box Jor electric cables (Fig. lll).
9) Tighten countersunk screws C ’hand-tight’.
O
O

5
Fig. III

6
Fig. IV

7
www.we-ef.com
TO9195W0115 © WE-EF 2015
Technical specifications are
subject to change.
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapacifi[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]