WE-EF RFL530-SE LED User manual

Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Post Mounted Luminaire
RFL530-SE LED
RFL540-SE LED

1
IP66, IK07, Class I, ta = 25°C
Post Mounted Luminaire
RFL530-SE RFL540-SE
ø 460 ø 570
ø 42 x 100
ø 460
81
19
ø 60 x 100
ø 570
82
38
Mounting height m
for RFL530-SE/RFL540-SE 3 - 6
Weight kg
for RFL530-SE 9.3
for RFL540-SE 15.0
Windage area m
2
RFL530-SE 0.166
RFL540-SE 0.255
Installation: horizontal, light output downwards,
Suitable for spigot diameter D = 60 x 80 mm or D = 76 x 80 mm
Upper pole offset D1 max. 102 mm

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
suitably qualiƂed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
The supply cable must be installed inside the pole and
not be exposed to the outside environment.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Installation Procedure
1) Switch off mains electrical supply.
2) Check that rating shown on luminaire label conforms
with mains electrical supply.
3) Feed mains cable Ainto outreach bracket Dand pole,
while setting luminaire assembly in position. Tighten
screws B.
4) Trim mains supply cable Ato the desired length and
connect leads to their respective terminals at the base
of pole (L = Phase, N = Neutral, = Earthing).

4
L
N
Supply cable

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9185W1017 © WE-EF 2017
Technical speciƂcations are
subject to change.