Adaptec 1405 User manual

Adaptec SATA/SAS
1405, 1045 Controller
Quick Start Guide
Kurzanleitung
Guide de démarrage
Guida di avvio rapida
Guía rápida
クィックスタートガイド
Controller Illustrations
SAS 1405 1045 QSG.book -1 ページ ２００８年１１月６日 木曜日 午前９時４５分

SAS 1405 1045 QSG.book 0 ページ ２００８年１１月６日 木曜日 午前９時４５分

Adaptec SAS/SATA
1405, 1045 Controller
Quick Start Guide
SAS 1405 1045 QSG.book -1 ページ ２００８年１１月６日 木曜日 午前９時４５分

SAS 1405 1045 QSG.book 0 ページ ２００８年１１月６日 木曜日 午前９時４５分

1
English
Introduction
This Quick Start Guide provides information on how to install your
Microsoft® Windows 2003/2008/XP/Vista™, SUSE® or Red Hat Linux®
operating system and Adaptec SATA/SAS 1405, 1045 controller driver.
For other installation options, refer to the Adaptec SATA/SAS 1405, 1045
Controller Installation and User’s Guide included on the controller
Installation CD. For controller illustrations, refer to the last section of this
document.
Note: For the latest information about the products described in this
Guide, for operating systems support, and to download drivers, visit
www.adaptec.com.
Package Contents
D Adaptec SATA/SAS 1405 or 1045 Controller
D Embedded in the controller’s BIOS are these utilities:
●Configuration Utility - Used to modify the controller and disk
drive settings
●Disk Utilities - Used to format and verify disk drives
D Adaptec installation CD containing:
●Drivers for the Adaptec controller
●Product Documentation for the Adaptec SATA/SAS 1405 or 1045
Controller
●Readme files
D Cable (1405 kit only)
D Low-profile bracket
D Adaptec SATA/SAS 1405, 1045 Controller Quick Start Guide (this
document in printed format)
SAS 1405 1045 QSG.book 1 ページ ２００８年１１月６日 木曜日 午前９時４５分

2
Step 1 Installing the Controller
Caution: Electrostatic Discharge (ESD) can damage your SATA/SAS
controller. Handle the controller carefully so that you do not expose it
to static charge.
aIf you have a low-profile computer cabinet, replace the original full-
height bracket on the controller card with the low-profile bracket
supplied in the controller kit.
bTurn off your computer and disconnect the power cord.
cOpen the system cabinet.
dRemove the cover from an available PCIe slot.
eInstall the controller in the PCIe slot and secure the controller bracket
to the chassis.
fConnect the SATA/SAS controller’s I2C connector (not available on all
models) to an I2C connector on an internal backplane or enclosure,
using an I2C cable.
gInstall and connect any internal disk drives using the appropriate
cable(s), then close the computer cabinet.
●All connectors are keyed so that you can insert the cables in only
one direction.
●Do not try to force a cable in to the controller or a disk drive. If the
connector does not slide on easily, try reversing it.
Step 2 Setting Up the Boot Sequence
The process you use to access your computer’s BIOS Setup program and
set the boot sequence varies by the computer manufacturer. Refer to the
instructions provided with your computer. The steps may be similar to:
aDuring startup, press the key combination (for example, <F2>, <F1>,
<DEL>) that starts the BIOS Setup program.
bGo to the menu used to specify the boot sequence. Put the CD drive
first—this allows you to perform Step 3 below.
cGo to the menu used to specify the boot priority for disk drives. Put
the controller first in this sequence.
dSave your changes, exit Setup, and then restart your computer.
!
SAS 1405 1045 QSG.book 2 ページ ２００８年１１月６日 木曜日 午前９時４５分

3
English
Step 3 Creating the Driver Disk
Before you install the driver, you need to create a driver disk. To create the
driver disk:
aInsert the Adaptec Controller CD and power on the computer to boot
from the CD.
bFollow the on-screen instructions to display the CD menu.
cClick Create Driver Disk, and select the required operating system.
dWhen prompted, insert a floppy disk, then click OK. The computer
creates the driver disk.
eRemove and label the driver disk.
fContinue with the installation of the operating system and controller
driver.
Step 4 Installing the Controller Driver with
the Operating System
Windows 2003/XP
aInsert the Windows CD, and restart the computer.
bWhen prompted to install a third-party driver, press F6.
Note: When F6 is active, a prompt appears at the bottom of the screen
for only 5 seconds. If you miss your chance to press F6, restart your
computer.
cInsert the driver disk, then wait until prompted to install the driver.
dPress S to specify that the driver is on the floppy disk, then press Enter.
The computer reads the disk.
eWhen the driver is found, press Enter. Follow the on-screen
instructions to complete the installation.
Windows Vista/Windows Server 2008
aInsert the Windows CD.
bWhen prompted to install a third-party driver, click Load Driver.
cBrowse to locate the driver and click Next to proceed with the
installation.
SAS 1405 1045 QSG.book 3 ページ ２００８年１１月６日 木曜日 午前９時４５分

4
Red Hat Linux
aInsert the Red Hat CD.
bRestart the computer.
cWhen the Red Hat Welcome screen opens, type expert or linux dd
at the boot prompt.
dWhen prompted, insert the driver disk you created, then select OK.
eFollow the on-screen instructions to set up the environment you want.
fIf you intend to install other third-party devices, install them now.
Otherwise, select Done.
gFollow the on-screen instructions to complete the Red Hat
installation.
SUSE Linux
aInsert the SUSE CD.
bRestart the computer.
cWhen the SUSE Installation menu opens, press the F6 key, select the
required installation option from the menu, then press Enter.
dWhen prompted, insert the driver disk you created, then press any key
to continue.
eFollow the on-screen instructions to set up the environment you want.
fIf you intend to install other third-party devices, install them now.
Otherwise, select Done.
gFollow the on-screen instructions to complete the SUSE installation.
SAS 1405 1045 QSG.book 4 ページ ２００８年１１月６日 木曜日 午前９時４５分

5
English
About Adaptec SATA/SAS 1405, 1045
Controllers
The controllers listed have met UL safety requirements for installation
and use in UL listed computers and Information Technology Equipment
(ITE) including server and network appliances.
For more information about Adaptec controllers, specifications, user
guides, and updates, visit www.adaptec.com.
To find detailed information about the controllers described in this
QuickStart Guide, refer to these documents:
●Readme—Text files located on the Adaptec Installation CD. These files
provide the late-breaking technical information.
●Adaptec Controller Installation and User’s Guide—PDF file located
on the Installation CD. It provides complete information on how to
install and configure your controller and attached devices.
SAS 1405 1045 QSG.book 5 ページ ２００８年１１月６日 木曜日 午前９時４５分

6
SAS 1405 1045 QSG.book 6 ページ ２００８年１１月６日 木曜日 午前９時４５分