Emerson SW93 User manual

CAUTION: Read all instructions carefully before installation.
Save this Owner's Manual for future reference.
Ceiling Fan Wall Control
Owner's Manual
Model No.
SW93
D AL FAN
CONTROL
• Maximum
3.0 AMP, 120 VAC,
60 HZ, Single-Pole
• 3-Speed Fan Motor
Control
Model No.
SW95
SINGLE FAN
CONTROL
• Maximum
1.25 AMP, 120 VAC,
60 HZ, Single-Pole
• 4-Speed Fan Motor
Control
Model No.
SW96
3-4 FAN
CONTROL
• Maximum
5.0 AMP, 120 VAC,
60 HZ, Single-Pole
• 4-Speed Fan Motor
Control
Part No. F40BP74990000 Form No. BP7499
Revision: 141110 U.L. odel No.: SW93/SW95/SW96
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 1

2U.L. odel No.: SW93/SW95/SW96
READ AND SAVE THESE INSTRUCTIONS
Table of Contents
Safety Instructions
Section Page
Safety Instructions . . . . . . . . . . . . 2-3
1. Unpacking Instructions . . . . . . . . 3
2. General Information . . . . . . . . . . 4
3. Wall Control Instructions . . . . 4-8
Section Page
4. Wall Control Wiring Diagrams . . 9
5. peration . . . . . . . . . . . . . . . . . 10
Limited Warranty . . . . . . . . . . . . . . 11
Additional Safety
Instructions for Installation
1.To avoid possible electrical
shock, be sure electricity is
turned off at the main fuse or
circuit breaker box before wiring.
2.Make certain no bare wires are
exposed outside the wire
connectors.
3.All wiring must conform to
National and ocal Electrical
Codes.
4.Follow the recommended
instructions for the proper
method of wiring your new Wall
Control. If you feel you do not
have enough electrical wiring
knowledge or experience, have
your Wall Control installed by a
licensed electrician. Any
electrical work not described in
this manual should be performed
by a licensed electrician.
TO REDUCE THE RISK OF FIRE,
E ECTRICA SHOCK, OR INJURY
TO PERSONS, OBSERVE THE
FO OWING:
a.Read your Owner’s Manual
carefully before installing the
Wall Control. Retain Owner’s
Manual for future reference.
b.Before servicing or cleaning
the ceiling fan, switch power
off at service panel and lock
service panel disconnecting
means to prevent power from
being switched on accident-
ally. When the service discon-
necting means cannot be
locked, securely fasten a
warning device such as a tag,
to the service panel.
!WARNING
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 2

3emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. odel No.: SW93/SW95/SW96
Safety Instructions Continued
1. npacking Instructions
WARNING: Use of this control
with some ceiling fans could result
in fire, shock and serious personal
injury. Use this speed control only
with Emerson CF series ceiling
fans that are suitable for use with
solid-state controls.
WARNING: This product is
designed for use with only those
ceiling fans designated specifically
for use with this product by
Emerson Electric Co. Substitution
of parts or accessories not
designated for use with this
product by Emerson Electric Co.
could result in personal injury or
property damage.
Do not install or use fan if any part is
damaged or missing. Call Toll-Free
for replacement parts:
1-800-654-3545
!WARNING
This product is designed to use only
those parts supplied with this
product and/or any accessories
designated specifically for use with
this product by Emerson Electric
Co. Substitution of parts or
accessories not designated for use
with this product by Emerson
Electric Co. could result in personal
injury or property damage.
!WARNING
A
C
B
PACKAGE CONTENTS
Part Description Qty.
A Wall Control Switch 1
B Knob 2
C Wire Connector 3
Tools Needed for Assembly
One Phillips head screwdriver
One blade screwdriver
One wire stripper
One stepladder
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 3

4U.L. odel No.: SW93/SW95/SW96
2. General Information
The SW93 & SW96 Wall Controls
are designed to operate multiple
ceiling fans, and Not any
accessory light kits.
The SW95 Wall Control is
designed to operate only one
ceiling fan, and Not an accessory
light kit.
The SW93 / SW95 / SW96 Wall
Controls do not require a receiver.
The SW93 Wall Control is rated for
3.0 Amp, 120 VAC, 60 HZ full load.
The SW95 Wall Control is rated for
1.25 Amp, 120 VAC, 60 HZ full
load.
The SW96 Wall Control is rated for
5.0 Amp, 120 VAC, HZ full load.
To avoid erratic speeds and
possible damage to your ceiling
fan, use the Wall Control only with
fans pull chain switches set to
their high speed settings.
All ceiling fans must be
completely installed before
installation of the Wall Control.
Your new Wall Control will require
a grounded electrical supply line
of 120 volts AC, 60 HZ circuit.
3. Wall Control Installation
Installation of Wall Control
replacing an Existing Wall
Control:
3.1
Disconnect electrical power to the
branch circuit at the circuit breaker
or fuse box before attempting to
install the ceiling fan mounting plate
on the outlet box.
NOTE: The ceiling fan must be set
at the highest speed setting
before installation of the Wall
Control.
Turning off wall switch is not
sufficient. To avoid possible
electrical shock, be sure electricity
is turned off at the main fuse box
before wiring. All wiring must be in
accordance with National and ocal
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
!WARNING
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 4

5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. odel No.: SW93/SW95/SW96
3. Wall Control Installation (Continued)
3.2
Remove the faceplate and the two 6-
32 screws from the existing wall
switch (retain faceplate and screws
for future use).
FACEPLATE
WALL OUTLET BOX
SWITCH
6-3 SCREWS (2)
3.3
Pull existing wall switch out from the
wall outlet box.
3.4
Disconnect the existing wall switch
wires from the wires in the outlet box
by removing the the two wire
connectors (discard connectors).
NEUTRAL
LEAD WIRES
WALL OUTLET BOX
EXISTING WALL SWITCH
SCREWS (2)
WIRE
CONNECTOR (2)
3.5
Set the new Wall Control in the FF
position (full counter-clockwise).
3.6
Pull the knob of the Wall Control
(retain for future use).
WALL CONTROL
KNOB
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 5

6U.L. odel No.: SW93/SW95/SW96
3. Wall Control Installation (Continued)
3.7
Connect the Wall Control BLACK
wire to the Fan/Motor Lead (BLACK
or RED) wire using a new wire
connector (supplied).
NOTE: Use only the wire
connectors supplied with the new
wall control to secure electrical
connections.
TO 120VAC
SOURCE HOT
FAN/MOTOR
BLACK OR RED
WIRE
WALL CONTROL
BLACK WIRE
TO FAN
MOTOR LOAD
WALL CONTROL
WIRE
CONNECTOR
3.8
Connect the Wall Control BLACK
wire to the 120 VAC source hot
BLACK wire using a new wire
connector (supplied).
TO 120VAC
SOURCE HOT
WALL CONTROL
BLACK WIRE
TO FAN
MOTOR LOAD
WALL
CONTROL
120 VAC HOT
BLACK WIRE
WIRE CONNECTOR
3.9
Securely connect the GREEN
ground wire from the Wall Control to
the supply ground wire (bare or
green).
WIRE
CONNECTOR
SUPPLY
GREEN
GROUND
WIRE
WALL CONTROL
GREEN
GROUND WIRE
Check to see that all wire
connections are tight, including
ground, and that no bare wire is
visible at the wire connectors,
except for ground.
!WARNING
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 6

Do not connect any neutral (WHITE)
wire to this control. Incorrect wiring
WI damage this control.
!WARNING
7
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. odel No.: SW93/SW95/SW96
3. Wall Control Installation (Continued)
3.10
NOTE: The WHITE neutral wires
inside the electrical box must be
connected together for proper
operation of the wall control.
NEVER connect the WHITE
neutral wires to the Wall Control.
TO 120VAC
SOURCE HOT
TO FAN
MOTOR LOAD
DO NOT CONNECT ANY WIRES
FROM WALL CONTROL TO THESE
WHITE NEUTRAL WIRES
3.11
Carefully tuck all wires and wire
connectors into the outlet box and
position the Wall Control onto the
outlet box.
WALL
CONTROL
WIRES TUCKED
INTO OUTLET BOX
POSITION THE
WALL CONTROL
INTO THE
OUTLET BOX
3.12
Place the previously removed
faceplate onto the Wall Control.
3.13
Assemble the faceplate to the Wall
Control using the two previously
removed 6-32 screws.
PREVIOUSLY
REMOVED
FACEPLATE
PREVIOUSLY REMOVED
6-32 SCREWS (2)
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 7

3. Wall Control Installation (Continued)
8U.L. odel No.: SW93/SW95/SW96
3.14
The Wall Control is supplied with a
white and almond knob. Select the
knob that matches the color of
existing faceplate.
3.15
Press knob onto the shaft of the Wall
Control.
3.16
Rotate knob counter-clockwise to
the full FFposition.
3.17
To Complete Installation: Restore
power at the main fuse box or circuit
breaker panel.
KNOB
WALL
CONTROL
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 8

9
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. odel No.: SW93/SW95/SW96
4. Wall Control Wiring Diagrams
4.1:SW93 Dual Fan Wall Control
TO NEUTRAL TO FAN MOTOR LOAD
TO 120VAC
SOURCE HOT
SW93 DUAL FAN
WALL CONTROL
MOTOR LOAD
BLACK
BLACK
BLACK or RED
BLACK
GREEN GREEN
4.2:SW95 Single Fan Wall Control
TO NEUTRAL TO FAN MOTOR LOAD
TO 120VAC
SOURCE HOT
SW95 SINGLE FAN
WALL CONTROL
BLACK
BLACK
BLACK or RED
BLACK
GREEN GREEN
4.3:SW96 3 or 4 Fan Wall Control (5 Amp Max.)
TO
NEUTRAL
TO FAN MOTOR LOAD
TO 120VAC
SOURCE HOT
SW96 3 or 4 FAN
WALL CONTROL
BLACK
BLACK
BLACK or RED
BLACK
GREEN GREEN
MOTOR
LOAD
MOTOR
LOAD
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 9

10 U.L. odel No.: SW93/SW95/SW96
5. Operation
CA TION
For fans equipped with built-in
variable speed devices: These
devices must be set at their
MAXIMUM SPEED for proper
operation. Adjustments to their
setting must only be made with
this fan control in the OFF
position. Changing or switching
these settings while the fan
control is in operation could
damage the control.
NOTE: Fan control knob turns fan
on at maximum speed to assist
motor start-up. Fan speed
decreases with clockwise rotation.
5.1
Set the fans on their HIGH speed
pull chain settings. Then use your
speed control to select any of the
speeds, plus FF.
NOTE: Fully counter-clockwise is
OFF. The three or four fan speeds
are selected by rotating the knob
one position at a time clockwise.
CHAIN COUPLER
3-SPEED SWITCH
PULL CHAIN
WALL
CONTROL
5.2
IMPORTANT
Always have the fan switch set to
HIGH speed before using the wall
control. To avoid accidental pull
chain use, shorten chain by
cutting it 1-inch below switch
body.
CHAIN COUPLER
SHORTENED
3-SPEED SWITCH
PULL CHAIN
1st Pull—HIGH
2nd Pull— edium
3rd Pull—Low
4th Pull—OFF
BP7499 SW93 SW95 SW96.qxp_Layout 1 12/1/14 2:39 PM Page 10