Addvent Elegance AVX100ES User manual

Figure 4
Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB www.addvent.co.uk
ISSUE 1: 0309
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
Operating Instructions for
AVX100ES, AVX100ET, AVX100EH
and AVX100ESBA, AVX100ETBA,
AVX100EHBA Elegance Fans
Figure 3 Electrical connection: Humidity model with Timer
Time delay and override operation
Terminal 1 = Neutral supply
Terminal 2 = switch LIVE supply
Terminal 3 = spare
Terminal 4 = permanent supply
Electrical Connections: Electronic Humidity Model – see Figure 3 below.
Connect to electrical supply as shown in figure 3.
For the fan to operate as a normal time delay unit with humidity over-ride, ie, when connected
with a switched live coming from the light switch into the fan, the fan will operate when the
light is switched on, and switch off after about 20 seconds to 20 minutes (timer is pre-set for
the minimum). However should the humidity in the room reach about 75% – which will
happen if the shower is run or the bath filled with hot water – the fan will switch on and keep
running until the humidity has been reduced to a normal level, about 65%.
Figure 5
Timer Humidity
Adjustments
Timer and humidity adjustment.
For the Timer model please see figure 4 below. For the Humidity model please see figure 5
below. Minimum and maximum values are shown on the diagrams.
WARNING: Only adjust with power switched off.
Specification
All AVX100 Elegance [4 inch] models:
220-240V ~50Hz; 20W ; Maximum operating temperature 4O°C; IP24.
IP
FIVE YEARS
EXCHANGE
5
24
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice
AVX100_ELEGANCEinstructions 12/3/09 14:17 Page 1

32
Safety Instructions
Installation
Mains supply must be switched off before any electrical connections or maintenance is
carried out.
lnstallation must be supervised by a competent electrician.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
Avoid the back-flow of gases into the room from the open flue of gas or other open-fire
appliances when mounted in outside windows or walls.
Before Installation
For best results this fan should be fitted as high on the wall as possible, or on the ceiling.
DO NOT install the fan within a shower cubicle.
This fan is double insulated and does not require an earth.
When installing fan through an external wall, an external wall grille must be fitted .
Installation
Cut a suitable diameter hole. Recommended size is Ø115mm (with or without board fixing
clips). lf the fan is to be fixed in the ceiling ensure that the hole is between the joists.
Remove the cover from the fan by twisting the front cover anti-clockwise.
Hold the body of the fan against the wall or ceiling and mark the four screw holes and the cable
entry on the side. Use the fixing clips to secure the fan in panel walls and ceilings – see figure 1a.
IMPORTANT: Ensure that the fan is square on wall or ceiling.
Bring the power cable into position, as marked. Allow an extra 230mm (9") protruding to
facilitate connection.
Figure 1
Wiring
NOTE: All wiring must be fixed securely and the cable to the fan should be a minimum of 1mm2
in section. All wiring must comply with current lEE Regulations. lf in any doubt contact a qualified
electrician.
Electrical Connection: Standard Model – see Figure 1.
Remove the internal cover by removing the 2 small caps and retaining crosshead screws to
access the terminal connections.
The fan can either be operated from a separate pullcord switch fitted to the ceiling of the
room or can be connected to the light switch so that the fan will start when the light is
switched on. A double pole fused spur having a contact separation of at least 3mm in all
poles must be used and fitted with a 3 amp fuse, and should be sited outside any room
containing a shower or fixed bath. The fan should not be accessible to a person using either
the shower or the bath.
Electrical connection: Standard model
Figure 2 Electrical connection: Timer model
Electrical Connections: Timer model – see Figure 2.
Remove the internal cover by removing the 2 small caps and retaining crosshead screws to
access the terminal connections. The fan can either be operated from a separate pullcord
switch fitted to the ceiling of the room or can be connected to the light switch so that the fan
will start when the light is switched on. A double pole fused spur having a contact separation
of at least 3mm in all poles must be used and fitted with a 3 Amp fuse, and should be sited
outside any room containing a shower or fixed bath. The fan should not be accessible to a
person using either the shower or the bath. See overleaf for timer adjustment instructions.
Top View
Figure 1a
Side View
Top View
AVX100_ELEGANCEinstructions 12/3/09 14:17 Page 2