Addvent Elegance AVX100 User manual

Figure 4
Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB
www.addvent.co.uk
ISSUE 2: 0110
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS PRODUCT,
CONSULT A COMPETENT ELECTRICIAN.
Operating Instructions for
AVX100 and AVX150
Elegance Fans
Figure 3 Electrical connection: Humidity model with Timer
Time delay and override
operation
Terminal 1 = Neutral supply
Terminal 2 = switch LIVE supply
Terminal 3 = spare
Terminal 4 = permanent supply
Electrical Connections: Electronic Humidity Model – see Figure 3 below.
Connect to electrical supply as shown in figure 3.
For the fan to operate as a normal time delay unit with humidity over-ride, ie, when
connected with a switched live coming from the light switch into the fan, the fan will
operate when the light is switched on, and switch off after about 20 seconds to 20
minutes (timer is pre-set for the minimum). However should the humidity in the room
reach about 75% – which will happen if the shower is run or the bath filled with hot
water – the fan will switch on and keep running until the humidity has been reduced to
a normal level, about 65%.
Figure 5
Timer Humidity
Adjustments
Timer and humidity adjustment.
For the Timer model please see figure 4 below. For the Humidity model please see
figure 5 below. Minimum and maximum values are shown on the diagrams.
WARNING: Only adjust with power switched off.
Specification
All Elegance AVX100 and AVX150 models:
220-240V ~50Hz; 20W ; Maximum operating temperature 4O°C; IP24.
IP
FIVE YEARS
EXCHANGE
5
24
ZONE
U
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice
ELEGANCE_RANGEinstructions 14/12/09 13:53 Page 1

32
Safety Instructions
Installation
Mains supply must be switched off before any electrical connections or maintenance is
carried out.
lnstallation must be supervised by a competent electrician.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Avoid the back-flow of gases into the room from the open flue of gas or other open-
fire appliances when mounted in outside windows or walls.
Before Installation
For best results this fan should be fitted as high on the wall as possible, or on the ceiling.
DO NOT install the fan within a shower cubicle.
This fan is double insulated and does not require an earth.
When installing fan through an external wall, an external wall grille must be fitted .
Installation
Cut a suitable diameter hole. Recommended sizes for plaster board fixing with fixing
clips are: 100 = Ø115mm and 150 = Ø173 mm; for all other surfaces 100 = Ø110mm
and 150 = Ø155mm. lf the fan is to be fixed in the ceiling ensure that the hole is
between the joists.
Remove the cover from the fan by twisting the front cover anti-clockwise.
Hold the body of the fan against the wall or ceiling and mark the four screw holes and
the cable entry on the side. Use the fixing clips to secure the fan in panel walls and
ceilings – see figure 1a.
IMPORTANT: Ensure that the fan is square on wall or ceiling.
Bring the power cable into position, as marked. Allow an extra 230mm (9") protruding
to facilitate connection.
Figure 1
Wiring
NOTE: All wiring must be fixed securely and the cable to the fan should be a minimum of
1mm2in section. All wiring must comply with current lEE Regulations. lf in any doubt
contact a qualified electrician.
Electrical Connection: Standard Model – see Figure 1.
Remove the internal cover by removing the 2 small caps and retaining crosshead screws
to access the terminal connections.
The fan can either be operated from a separate pullcord switch fitted to the ceiling of
the room or can be connected to the light switch so that the fan will start when the
light is switched on. A double pole fused spur having a contact separation of at least
3mm in all poles must be used and fitted with a 3 amp fuse, and should be sited
outside any room containing a shower or fixed bath. The fan should not be accessible to
a person using either the shower or the bath.
Electrical connection: Standard model
Figure 2 Electrical connection: Timer model
Electrical Connections: Timer model – see Figure 2.
Remove the internal cover by removing the 2 small caps and retaining crosshead
screws to access the terminal connections. The fan can either be operated from a
separate pullcord switch fitted to the ceiling of the room or can be connected to the
light switch so that the fan will start when the light is switched on. A double pole
fused spur having a contact separation of at least 3mm in all poles must be used and
fitted with a 3 Amp fuse, and should be sited outside any room containing a shower
or fixed bath. The fan should not be accessible to a person using either the shower or
the bath. See overleaf for timer adjustment instructions.
Top View
Figure 1a
Side View
Top View
ELEGANCE_RANGEinstructions 14/12/09 13:53 Page 2