adeptus 78101 User manual

ASSEMBLY INSTRUCTIONS
Cottage Single Drawer End Table / Nightstand
#78101 - White Finish
1-11B;- PO ADE201808
CUSTOMER SERVICE AND REPLACEMENT PARTS:
)25)$67(56(59,&(213$5763/($6(*272285:(%6,7($7WWW.ADEPTUS.COM;
25&$//72//)5(($'(3786)25$66(0%/<48(67,216
021)5,$07230(67&/26('+2/,'$<6.
IF YOU CALL, PLEASE HAVE ON HAND:
x352'8&71$0($1'672&.180%(5
x:+(1$1':+(5(7+(81,7:$6385&+$6('
x32180%(5)5207+(%277202)7+,63$*(
,):($5(%86<+(/3,1*27+(5&86720(563/($6(/($9(<281$0($1'180%(5
725(&(,9($5(7851&$//
<2855(7$,/(50$<$/623529,'(6(59,&(253$576
HELPFUL OVERALL:
x6$9(7+(6(,16758&7,216+((76$1'7+(%2;817,/<28$5(6$7,6),(':,7+7+($66(0%/<
x'2127*/8(7+(3$5762)7+(81,772*(7+(581/(66<28+$9(7(67('7+($66(0%/<),567
x3(5)2507+($66(0%/<21$&/($1+$5'685)$&(86,1*7+()/$77(1('&$572125$72:(/
723527(&77+(685)$&($1'7+(),1,6+2)7+(81,7'2127$66(0%/(21&$53(7
VISIT WWW.ADEPTUS.COM TO REGISTER YOUR PRODUCT AND SEE THE
COMPLETE ADEPTUS LINE. REGISTRATION IS REQUIRED FOR PARTS REQUESTS.
THANK YOU FOR YOUR PURCHASE AND WELCOME TO ADEPTUS!
127,&(7+(:5,77(1,16758&7,216CONTAINED +(5(,1$5(&23<5,*+7('

*.G ([," >K[3)" [I))[
W/([ C-4[7[([)2Q"4[ 4[3[
Q44([[ L-X+[4)08[-)&[)(4*7[
*-W7[43O(['([W7F1[([
([/; " ([4P[/4[)$43[)([
D4[4: %[E7I ""33V14[
")I[*/ 4[Q#9[(4H4/7[=U4[4J*4(34[
W(< )([([)/[34(34[
[/4K[334&Q"4[ B&[/W43[
A(3*)-7= )([([I/4N)$ ([
)375[IUMP[U4"*[YSX1[/; "4/[
!44*[7U4 /[*/ 43[ /43)(R"4[()I[
YSW/4[) ( ([=6&[4*@[
I 7P[?4[M[("[3B*[334&Q"[
ZYTW334&Q"4[YSW3H4r
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
2-1
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('
This is a SOLID WOOD product:
We inspect all wood and follow quality assurance guidelines that pass third-party inspections.
Note: Real wood has knots, small cracks, and what may look like blemishes. These characteristics
are expected when producing furniture from natural material.
We take extra care with our drawer parts:
1. We use real wood drawer sides and drawer backs.
2. Drawer sides and backs are not finished to protect fabrics from any residual paint odor.
3. Drawer parts are finely sanded to prevent snags.

These tools are not supplied by the manufacturer.
Safety and Care Advice
45 min
0DQXDO
3KLOOSVKHDG
6FUHZGULYHU
+DPPHU
1R3RZHU7RROV
PLEASE NOTE:
'2:(/63$57$9$5<(9(5626/,*+7/<,)$'2:(/3$57$,6/226(,
:(35()(5<28&$//28572//)5(( 180%(5)25$'',7,21$/'2:(/6
96*/8,1*7+('2:(/
,)<28&+226(72*/8(7+(3$576 &203/(7(/<7(677+($66(0%/<),567
:('21276833/<*/8(
Perform assembly on a clean, hard
surface using the flattened box or a
towel to protect the surface & the unit's
finish. DO NOT assemble on carpet.
Carpet creates too much bounce
making assembly difficult and could
lead to damage of the parts.
DO NOT FORCE OR
OVER-TIGHTEN THE
SCREWS. DOING SO CAN
DAMAGE THE PARTS.
3-1
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('
·Check you have all the components and tools listed on pages 3 & 4.
·Remove all fittings from the plastic bags and separate them into their groups.
·Keep children and animals away from the work area, small parts could choke if swallowed.
·Make sure you have enough space to layout the parts before starting.
·Do not stand or put weight on the product, this could cause damage.
·Assemble the item as close to its final position (in the same room) as possible.
·Opened box can be used to protect your floor or counter during assembly.
·Assembly is easier for drawer parts on a counter.
·Parts of the assembly will be easier with 2 people.
·We do not recommend the use of power drill/drivers for inserting screws, as this could
damage the unit.
·Only use hand screwdrivers.
·Dispose of all packaging carefully and responsibly.
·Never sit, stand or allow children to climb on the assembled unit.
"L" Square Tool

A=26B=23 O=04 D=08 E=01F=01
H=04 K=11
G=01
8 x 30
mm
Dowel
4 x 30 3.5 x 14
mm mm
6 x 10
mm
Screw Screw
Left
Drawer
Runner
Right
Drawer
Runner Knob
Screw
Back Panel
Nail
Foot
1
1
1
2
1
2
2
1
1
1
1
1
1
01
12
02
03
04
04
05
06
07
08
09
10
11
4-1
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('

PREPARE PARTS BY INSERTING DOWELS
1A=24
8 x 30
mm
Dowel
Prepare the parts for assembly by inserting dowels (part A) into the pre-drilled dowel holes in the following parts:
•Insert 2 dowels (part A) into the top of each side panel; 1 right facing side panel (part 02) and 1 left facing side panel (part 03).
•Insert 2 dowels (part A) into each side of the shelf (part 07).
•Insert 2 dowels (part A) into the front of each drawer side; 1 right facing drawer side (part 10) and 1 left facing drawer side
(part 11).
•Insert 2 dowels (part A) into both ends of each crossbar; 2 drawer crossbars (part 04) and 1 bottom crossbar (part 05).
A
A
A
A
11
07
03
02
05
04
10
A
A
A
A
A
A
A
A
AAAA
A
A
AA
A
2
O
O=04
Foot
ATTACH THE FEET TO THE LEGS
NOTE: The pre-drilled pocket holes are at the top of the side panels. The feet go on the opposite end.
Attach the 4 feet (part O) to the 4 legs attached to both of the side panels (parts 02 & 03) by screwing the foot
(part O) into the bottom of each leg clockwise just until tight. Do not try to force or over-tighten the feet as this
could cause the wood to split.
51
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('
0203
PRE-DRILLED POCKET HOLES
(TOP OF PANELS).

3ATTACH THE LEFT DRAWER RUNNER (250E) TO THE LEFT
FACING SIDE (PANEL HALF OF RUNNER SET)
NOTE: The end of the Left
drawer runner (part E) with the
wheel should be on the
front side of the Left-facing
side panel (part 03).
03
02
4ATTACH THE RIGHT DRAWER RUNNER (250D) TO THE
RIGHT FACING SIDE (PANEL HALF OF RUNNER SET)
NOTE: The end of the Right
drawer runner (part F) with
the wheel should be on
the front side of the Right-
facing side panel (part 02).
FRONT
BACK
FRONT
BACK
61
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('

7-11
6
B=05 4 x 30
mm
Screw
ATTACH CROSSBARS AND SHELF TO
LEFT SIDE PANEL
•Attach all crossbars and the shelf (parts 04, 05 & 09) to the Left side panel (part 03) by first aligning the dowels (part A) inserted
in step 1 with the pre-drilled dowel holes in the Left-facing side panel (part 03) as shown.
•Once aligned, push all crossbars and the shelf (parts 04, 05 & 09) into the the Left-facing side panel (part 03) until flush.
•Then secure each one using 5 of the part B screws, as shown.
•The part B screw should be just tight. Do not force or over-tighten as this could cause damage to the panel, crossbars and/or shelf.
B
B
B
B
B
03
LEFT-FACING PANEL
04
04
05
09
A
A
A
A
A
B=05 4 x 30
mm
Screw
ATTACH RIGHT SIDE PANEL TO
CROSSBARS AND SHELF
NOTE: Do not attempt to
complete this step with
the unit upright. It should
be flat on its front side
on a hard, clean surface.
B
B
B
B
B
02
RIGHT-FACING SIDE PANEL
A
A
A
•Attach all crossbars and the shelf (parts 04, 05 & 09) to the Right side panel (part 02) by first aligning the dowels (part A) you
inserted in step 1 with the pre-drilled dowel holes in the Right side panel (part 02) as shown.
•Once aligned, push all crossbars and the shelf (parts 04, 05 & 09) into the the Right side panel (part 02) until flush.
•Then secure each one using 5 of the part B screws, as shown.
•The part B screw should be just tight. Do not force or over-tighten as this could cause damage to the panel, crossbars and/or shelf.
5
03
A
09
05
A
A
A
A
A
04
04
A
A
LEFT PANEL
NOTE: UNIT IS
PICTURED LAYING
FLAT ON ITS
FRONT SIDE.
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('

8-11
7
B=04
B
B
B
TOP
B
4 x 30
mm
Screw
ATTACH THE TOP
A
A
A
A
•Attach the top of the unit (part 01) by first aligning the 4 dowels
(part A) that you installed in the side panels (parts 02 & 03) in
step 1 with the pre-drilled dowel holes in the top (part 01).
•Once aligned, push the the top (part 01) to the partially
assembled unit until flush.
•Secure the top (part 01) to the unit using 4 part B screws on
each corner as shown.
•Part B screws should just be tight. Do not try to force or over-
tighten screws as this could cause damage to parts.
NOTE: It is easier to secure the top (part 01)
with the screws (part B) with the the unit
turned over (upside down) and on a hard,
clean surface.
K
K
K
K
K
K
K
K
K
K
K
27 mm
27 mm
90°
°06
90°
8
K=11
Back Panel
Nail
ATTACH THE
BACK PANEL
Before attaching the back
panel, make sure the unit is
assembled squarely. Use an
"L" Square tool, if necessary,
as shown.
•First make sure the unit is assembled squarely. Use an "L" Square tool, if necessary.
•Once the unit is square, you must determine the square installation of the back
panel. Use an "L" Square tool, if necessary.
•Once you have positioned the back panel (part 08) squarely, secure it to the unit
using 11 of part K nails evenly spaced, as shown.
•It is very important that you utilize all 11 nails. It strengthens the unit.
!
Use all back panel
nails (part K)
evenly spaced.
They make the
unit strong.
03
01
02
08
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('

NOTICE: THE WRITTEN INSTRUCTIONS CONTAINED HEREIN ARE COPYRIGHTED.
A
A
A
A
9
B=10 G=02E=01
(300E)
F=01
(300D)
D=06
2x B
B
B
4 x 30
mm
Screw
ASSEMBLE THE DRAWER
3.5 x 14
mm
Screw
Left
Drawer
Runner
Right
Drawer
Runner
Knob
B
B
B
B
G
F
D
D
D
DED
D
STEP 14 - E
With the drawer upside down,
•Align the left drawer runner (300E) (part E) with the wheel on the outside
toward the drawer back (part 13). Make sure the opposite end is all
the way forward touching the drawer front (part 09), as shown.
•Secure the left drawer runner (300E) (part E) to the left drawer side (part
11) using 3 screws (part D).
•The first screw (part D) goes through the 3rd hole back from the drawer
front (part 09) and into the left drawer side (part 11).
•The second screw (part D) goes through the center hole of the runner
(300E) (part E) into the left drawer side (part 11).
•The third screw (part D) goes through the last hole in the runner (300E)
(part E) closest to the drawer back (part 13) on the outside by the wheel
as shown.
•Repeat these steps to attach the (300D) right drawer runner (part F) to
the right drawer side (part 12).
67(34'
•Attach the knobs (part G) to the drawer
front (part 09) by inserting the screw
(part B) through the back of the drawer
front (part 09) and into the back of the
knob (part G). (2 extra part G knobs
supplied.)
$OOVFUHZVSDUWV%'VKRXOGEHWLJKWEXWGR
QRWIRUFHRUWU\WRRYHUWLJKWHQDVWKLVPD\FDXVH
GDPDJHWRWKHXQLW
7XUQ
'UDZHU
2YHU
B
G
B
09
10
11
12
13
14 14
09
11
09
09
11
11
12
12
14
13
STEP 14 - A
•Using the dowels (part A) inserted into parts 11 and 12 in step 1, align the
drawer sides (parts 11 & 12) with the drawer front (part 09).
•Make sure the groove for the drawer bottom (part 14) is precisely aligned
on all 3 parts (09, 11 & 12) then push together until flush.
•Secure the drawer sides (parts 11 & 12) to the drawer front (part 09) using
2 screws (part B) on each side as shown in the illustration.
•Screws (part B) should be tight, but do not force or over-tighten as this
could cause the wood to split.
STEP 14 - B
•Slide the drawer bottom (part 14) into
the grooves on parts 09, 11 and 12 as
shown
STEP 14 - C
•Align the groove in the drawer back (part
13) with the drawer bottom (part 14) and in
between the drawer sides (parts 11 & 12).
•Secure the drawer back (part 13) to the
drawer using 2 screws (part B) on each
side, as shown.
(300E)

10-11
10 INSTALL THE DRAWER
•Tilt the back of the drawer upward to get
it past the wheels on the drawer runners.
•Once clear of the wheels, you can level
the drawer and slide it in.
11
D=02 D
After completed assembly, it is
necessary to adjust the drawer
alignment to get the drawer
perfectly square.
To adjust the drawer front position:
•Loosen the screw (part H) you used to
install the drawer runner (either parts E
or F) in steps 5 or 6, to the side panel
(parts 02 or 03), depending on the side
(left or right), as shown.
•With the screw (part H) loosened, you
can make the necessary slight
adjustments (up or down) to the drawer
runner to achieve the proper drawer
alignment.
Once the drawer alignment is square, secure
the position of the drawer runners (parts E &
F) to the side panels (parts 02 & 03) by re-
tightening the part H screw and adding the
part D screw as shown.
Complete these steps for both the left and the
right side of the drawer.
ADJUST DRAWER ALIGNMENT
3.5 x 14
mm
Screw
H
H
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('

11-11
Completed Assembly!
Thank you for your purchase.
Welcome to ADEPTUS!
Care and use instructions:
Use for general home use as an end table or nightstand with storage.
Clean with a damp cloth and wipe dry.
Do not use harsh chemicals or abrasive sponges or cloths that could
damage the finish.
NOTICE: 7+(:5,77(1 ,16758&7,216 CONTAINED +(5(,1$5( &23<5,*+7('
Table of contents
Other adeptus LCD Drawer manuals
Popular LCD Drawer manuals by other brands

Acnodes
Acnodes MKD6220D user manual

Neuro Logic Systems
Neuro Logic Systems NLS 1U Server Console RFT-17 installation guide

Rose electronics
Rose electronics RackView RV1-CKVM15A features and benefits

Acnodes
Acnodes KD84174 user manual

Costway
Costway EP22469 user manual

Fisher & Paykel
Fisher & Paykel COOLDRAWER Installation instructions manual