ADJ Focus Spot Three Z Pearl User manual

User Instructions
Rev. 2/17
©2016 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as-
sembly, installation, rigging, and operation of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Focus spot three Z pearl

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 2
• DMX-512 Protocol Compatible (2 DMX Channel Modes: 18 Chan-
nels & 21 Channels)
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)
• Internal Microphone
• Digital Display for Address and Function Setting
• 4 Preprogrammed Shows
• UC IR and Airstream IR Compatiable (Not Included)
Focus Spot Three Z Pearl Features
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
Focus Spot Three Z Pearl Handling Precautions
Focus Spot Three Z Pearl Warranty Registration
The Focus Spot Three Z Pearl carries a 2 year (730 days) limited
warranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online
at www. adjproducts.com. All returned service items whether under
warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. If the unit is under warranty you must
provide a copy of your proof of purchase invoice. Please contact ADJ
Products, LLC customer support for a R.A. number.
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Focus Spot Three Z Pearl General InstructionsFocus Spot Three Z Pearl General Information
Unpacking: Thank you for purchasing the Focus Spot Three Z Pearl
by ADJ Products, LLC. Every Focus Spot Three Z Pearl has been
thoroughly tested and has been shipped in perfect operating condi-
tion. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, care-
fully inspect your xture for any damage and be sure all equipment
necessary to operate the unit has arrived intact. In the event damage
has been found or parts are missing, please contact our toll free cus-
tomer support number for further instructions. Please do not return
this unit to your dealer without contacting customer support rst.
Introduction: The Focus Spot Three Z Pearl is a DMX intelligent,
moving head, mini LED was. The Focus Spot Three Z Pearl can oper-
ate as a stand alone fixture or in a Master/Slave set up. The Focus
Spot Three Z Pearl has three operating modes; a sound active, show
mode, DMX controlled. This fixture is suitable for theaters, studios,
retail stores, and other similar locations. For best results use fog or
special effects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 36 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
Focus Spot Three Z Pearl Safety Precautions
ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 4
The Focus Spot Three Z Pearl is fully operational in three dierent
mounting positions, hanging upside-down from a ceiling, mounted
sideways on trussing, or set on a at level surface. Be sure this xture
is kept at least 0.5m away from any ammable materials (decoration
etc.). Always use and install the supplied safety cable as a safety
measure to prevent accidental damage and/or injury in the event the
clamp fails (see next page).
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attach-
ment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculat-
ing working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
Focus Spot Three Z Pearl Mounting

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 7
Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the omega locks to the
bottom of the Focus Spot Three Z Pearl. Attach and pull the
safety-cable through one of the safety holes located on the
bottom base and over the trussing system or a safe xation
spot. Insert the end in the carabine and tighten the safety
screw.
NOTICE: The suitable enviromental temperature for this light-
ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Focus Spot Three Z Pearl Mounting Focus Spot Three Z Pearl CAD Drawing
489mm/19.25”
284mm/11.1’ 183mm/7.20”

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 8
Power Supply: The ADJ Focus Spot Three Z Pearl contains a auto-
matic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Focus Spot Three Z Pearl can be controlled via DMX-
512 protocol. The Focus Spot Three Z Pearl has
2 DMX channel modes; 18 channel mode & 21
channel mode. The DMX address is set electroni-
cally using the controls on the front panel of the
unit. Your unit and your DMX controller require a
approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
Focus Spot Three Z Pearl DMX Set Up
Figure 1
Focus Spot Three Z Pearl Base Layout
1. LED: 
DMX On DMXinputpresent
MASTER On MasterMode
SLAVE ON SlaveMode
SOUND Flashing Soundactivation
2. Display:Toshowthevariousmenusandtheselectedfunction;
3. Button:
MENU Toselecttheprogramming functions
 UP  Togoforwardintheselectedfunctions 
 DOWN Togobackwardintheselectedfunctions
ENTER Toconrmtheselectedfunctions
4. IRreceiver: ToreceivetheIRsignal;
5. Fuse(T5Amp): Protectstheunitfromover‐voltageorshortcircuit;
6. PowerIn/out: powercableconnectorsforpowerinput/output;
7. DMXIn/Out:  3‐pinXLRconnectorsforDMX512operation.

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 11
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Pin 5 - Do Not Use
Pin 4 - Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Focus Spot Three Z Pearl DMX Set Up
shielded cable (This cable may be purchased at almost all professional
sound and lighting stores). Your cables should be made with a male
and female XLR connector on either end of the cable. Also remember
that DMX cable must be daisy chained and cannot be split.
Focus Spot Three Z Pearl DMX Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 2
Figure 3
1 Ground 1 Ground
XLR Male Socket XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 4

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 13
Focus Spot Three Z Pearl 18 Channel Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT 0° - 540°
2 0 - 255 TILT MOVEMENT 0° - 270°
3 COLOR
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 PURPLE
50 - 56 LIGHT BLUE
57 - 63 PINK
64 - 127 COLOR MIXING
128 - 189 COUNTER CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
4 GOBOS (STATIC)
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 72 GOBO 1 SHAKE
73 - 81 GOBO 2 SHAKE
82 - 90 GOBO 3 SHAKE
91 - 99 GOBO 4 SHAKE
100 - 108 GOBO 5 SHAKE
109 - 117 GOBO 6 SHAKE
118 - 127 GOBO 7 SHAKE
128 - 189 COUNTER CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
Focus Spot Three Z Pearl 18 Channel Mode
Channel Value Function
5 GOBOS (ROTATING)
0 - 9 OPEN
10 - 18 GOBO 1
19 - 27 GOBO 2
28 - 36 GOBO 3
37 - 45 GOBO 4
46 - 54 GOBO 5
55 - 63 GOBO 6
64 - 73 OPEN
74 - 82 GOBO 1 SHAKE
83 - 91 GOBO 2 SHAKE
92 - 100 GOBO 3 SHAKE
101 - 109 GOBO 4 SHAKE
110 - 118 GOBO 5 SHAKE
119 - 127 GOBO 6 SHAKE
128 - 189 COUNTER CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
6 GOBO WHEEL 2 GOBO ROTATION
0 - 127 INDEXING
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 NO ROTATION
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
7 PRISM
0 STOP
1 - 126 6 FACET PRISM
127 NO EFFECT
128 - 255 LINEAR PRISM
8 PRISM ROTATION
0 - 3 STOP
4 - 127 COUNTER CLOCKWISE ROTATION
FAST - SLOW
128 - 131 STOP
132 - 255 CLOCKWISE ROTATION SLOW - FAST

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 14
Focus Spot Three Z Pearl 18 Channel Mode
Channel Value Function
9 STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
10 0 - 255 MASTER DIMMER 0% - 100%
11 0 - 255 FOCUS 0% - 100%
12 AUTO FOCUS
0 - 7 NOTHING
8 - 63 5M FOR AUTO FOCUS
64 - 127 10M FOR AUTO FOCUS
128 - 255 15M FOR AUTO FOCUS
13 0 - 255 ZOOM 18° - 12°
14 SHOWS
0 OFF
1 - 21 SHOW 1
22 - 41 SHOW 2
42 - 61 SHOW 3
62 - 81 SHOW 4
82 - 255 RANDOM SHOW WITH SOUND ACTIVITY
15 0 - 255 SHOW SPEED FAST - SLOW
16 DIMMER MODES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT
17 0 - 255 PAN/TILT SPEED FAST - SLOW
Focus Spot Three Z Pearl 18 Channel Mode
Channel Value Function
18 FUNCTION
0 - 69 NOTHING
70 - 79 ENABLE BLACKOUT WITH PAN/TILT
80 - 89 DISABLE BLACKOUT WITH PAN/TILT
90 - 99 ENABLE BLACKOUT W/ COLOR CHANGE
100 - 109 DISABLE BLACKOUT W/ COLOR CHANGE
110 - 119 ENABLE BLACKOUT W/ GOBO CHANGE
120 - 129 DISABLE BLACKOUT W/ GOBO CHANGE
130 - 139 PAN/TILT MOTOR RESET
140 - 149 COLOR WHEEL MOTOR RESET
150 - 159 GOBO WHEEL MOTOR RESET
160 - 169 EFFECTS RESET (PRISM/FOCUS/ZOOM)
170 - 199 NOTHING
200 - 209 RESET ALL
210 - 255 NOTHING
Gobo 1 Gobo 7Gobo 6Gobo 5Gobo 4Gobo 3Gobo 2
23.80 mm
20.00 mm
20.00 mm
23.80 mm
20.00 mm
23.80 mm
23.80 mm
20.00 mm
20.90 mm
17.00 mm
Gobo 1
Gobo 5Gobo 4
Gobo 3Gobo 2
23.80 mm
20.00 mm
Gobo 6
Gobo Wheel 1
Gobo Wheel 2

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 17
Focus Spot Three Z Pearl 21 Channel Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT 0° - 540°
2 0 - 255 PAN FINE 0% - 100%
3 0 - 255 TILT MOVEMENT 0° - 270°
4 0 - 255 TILT FINE 0% - 100%
5 COLOR
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 PURPLE
50 - 56 LIGHT BLUE
57 - 63 PINK
64 - 127 COLOR MIXING
128 - 189 COUNTER CLOCKWISE FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
6 GOBOS (STATIC)
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 72 GOBO 1 SHAKE
73 - 81 GOBO 2 SHAKE
82 - 90 GOBO 3 SHAKE
91 - 99 GOBO 4 SHAKE
100 - 108 GOBO 5 SHAKE
109 - 117 GOBO 6 SHAKE
118 - 127 GOBO 7 SHAKE
128 - 189 COUNTER CLOCKWISE FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
Focus Spot Three Z Pearl 21 Channel Mode
Channel Value Function
7 GOBOS (ROTATING)
0 - 9 OPEN
10 - 18 GOBO 1
19 - 27 GOBO 2
28 - 36 GOBO 3
37 - 45 GOBO 4
46 - 54 GOBO 5
55 - 63 GOBO 6
64 - 73 OPEN
74 - 82 GOBO 1 SHAKE
83 - 91 GOBO 2 SHAKE
92 - 100 GOBO 3 SHAKE
101 - 109 GOBO 4 SHAKE
110 - 118 GOBO 5 SHAKE
119 - 127 GOBO 6 SHAKE
128 - 189 COUNTER CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
8 GOBO WHEEL 2 GOBO ROTATION
0 - 127 INDEXING
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 NO ROTATION
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
9 PRISM
0 STOP
1 - 126 6 FACET PRISM
127 NO EFFECT
128 - 255 LINEAR PRISM
10 PRISM ROTATION
0 - 3 STOP
4 - 127 COUNTER CLOCKWISE ROTATION
FAST - SLOW
128 - 131 STOP
132 - 255 CLOCKWISE ROTATION SLOW - FAST

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Pearl Instruction Manual Page 19
Focus Spot Three Z Pearl 21 Channel Mode
Channel Value Function
11 STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
12 0 - 255 MASTER DIMMER 0% - 100%
13 0 - 255 MASTER DIMMER FINE 0% - 100%
14 0 - 255 FOCUS 0% - 100%
15 AUTO FOCUS
0 - 7 NOTHING
8 - 63 5M FOR AUTO FOCUS
64 - 127 10M FOR AUTO FOCUS
128 - 255 15M FOR AUTO FOCUS
16 0 - 255 ZOOM 18° - 12°
17 SHOWS
0 OFF
1 - 21 SHOW 1
22 - 41 SHOW 2
42 - 61 SHOW 3
62 - 81 SHOW 4
82 - 255 RANDOM SHOW WITH SOUND ACTIVITY
18 0 - 255 SHOW SPEED FAST - SLOW
19 DIMMER MODES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT
20 0 - 255 PAN/TILT SPEED FAST - SLOW
Focus Spot Three Z Pearl 21 Channel Mode
Channel Value Function
21 FUNCTION
0 - 69 NOTHING
70 - 79 ENABLE BLACKOUT WITH PAN/TILT
80 - 89 DISABLE BLACKOUT WITH PAN/TILT
90 - 99 ENABLE BLACKOUT W/ COLOR CHANGE
100 - 109 DISABLE BLACKOUT W/ COLOR CHANGE
110 - 119 ENABLE BLACKOUT W/ GOBO CHANGE
120 - 129 DISABLE BLACKOUT W/ GOBO CHANGE
130 - 139 PAN/TILT MOTOR RESET
140 - 149 COLOR WHEEL MOTOR RESET
150 - 159 GOBO WHEEL MOTOR RESET
160 - 169 EFFECTS RESET (PRISM/FOCUS/ZOOM)
170 - 199 NOTHING
200 - 209 RESET ALL
210 - 255 NOTHING
Gobo 1 Gobo 7Gobo 6Gobo 5Gobo 4Gobo 3Gobo 2
23.80 mm
20.00 mm
20.00 mm
23.80 mm
20.00 mm
23.80 mm
23.80 mm
20.00 mm
20.90 mm
17.00 mm
Gobo 1
Gobo 5Gobo 4
Gobo 3Gobo 2
23.80 mm
20.00 mm
Gobo 6
Gobo Wheel 1
Gobo Wheel 2