ADJ VIZI BEAM 12RX User manual

ADJ VIZI BEAM 12RX
User Manual

2
©2020 ADJ PRODUCTS LLC all rights reserved. Information, specications, diagrams, images, and instructions
herein are subject to change without notice. ADJ logo and identifying product names and numbers herein are
trademarks of ADJ PRODUCTS LLC. Copyright protection claimed includes all forms and matters of copyrightable
materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in
this document may be trademarks or registered trademarks of their respective companies and are hereby
acknowledged. All non-ADJ brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ PRODUCTS LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment,
building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the
use or reliance of any information contained within this document, and/or as a result of the improper, unsafe,
insucient and negligent assembly, installation, rigging, and operation of this product.
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA 90040
323-582-2650 | Fax [phone] | www.adj.com |[email protected]
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone] | www.adj.eu |[email protected]
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000 [phone] | [email protected]
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version
of this document may be available online.
Please check www.adj.com for the latest revision/update of this manual,
before beginning installation and/or programming.
Date Document Version SoftwareVersion
≥
DMX Channel Modes Notes
06/26/2020 1.0 1.2 13/17 Initial Release

3
General Information 4
Limited Warranty (USA Only) 5
Safety Guidelines 6
Discharge Lamp Warning 8
Maintenance Guidelines 9
Fixture Overview 10
Color Wheel 11
Gobo Wheel 12
Lamp Replacement 13
Installation Guildelines 14
System Menu 18
DMX Traits: Channel Functions & Values 24
Error Codes 27
Specications 28
Optional Accessories 31
CONTENTS

4
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to
operate this device. These instructions contain important safety and use information.
This product is intended for use by professionally trained personnel only, and is not suitable for
private use.
Unpacking
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during shipping. If the carton is damaged,
carefully inspect the device for damage, and be sure all accessories necessary to install and operate the
device have arrived intact. In the event damage has been found or parts are missing, please contact our
customer support team for further instructions. Please do not return this device to your dealer without rst
contacting customer support. Please do not discard the shipping carton in the trash. Please recycle
whenever possible.
BOX CONTENTS
Omega Brackets
1.83M locking power cable
Customer SUPPORT
Contact ADJ Service for any product related service and support needs.
Also visit forums.adj.com with questions, comments or suggestions.
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-2650 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax: [phone] | [email protected]
REPLACEMENT PARTS please visit parts.adj.com
IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR
MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO
THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES
IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT
TO WARRANTY CLAIMS AND/OR REPAIRS.

5
LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of
manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see
specic warranty period on reverse). This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to establish the
date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product back—
please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ
Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges
only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its
original package and packaging material. No accessories should be shipped with the product. If any
accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever for loss of or
damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is
modied in any manner which ADJ Products, LLC concludes, after inspection, aects the reliability of the
product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged
because it was not properly maintained as set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic checkup.
During the period specied above, ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in
material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to
the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC.
All products covered by this warranty were manufactured after August 15, 2012, and bear identifying marks to
that eect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made by
ADJ Products, LLC in connection with this product, including warranties of merchantability or tness, are
limited in duration to the warranty period set forth above. And all warranties, whether expressed or implied,
including warranties of merchantability or tness, are limited in duration to the warranty period set forth above.
The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided
above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or damage, direct and/
or consequential arising out of the use of, and/or inability to use this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all prior
warranties and written descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
Non-LED Lighting Products = 1-Year (365 Days) (IncludingSpecialEffect Lighting, Intelligent Lighting, UV lighting,Strobes,
Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED
and lamps)
Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)
NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.
StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)
ADJ DMX Controllers = 2 Year (730 Days)
American Audio Products = 1 Year (365 Days)
CUSTOMER SUPPORT INFORMATION
Contact ADJ Service for any product related service and support needs.
Also visit forums.adj.com with questions, comments or suggestions.
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-2650 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax: [phone] | [email protected]

6
SAFETY GUIDELINES
This xture is a sophisticated piece of electronic equipment. To guarantee smooth
operation, it is important to follow all instructions and guidelines in this manual. ADJ
PRODUCTS, LLC is not responsible for injury and/or damages resulting from the misuse
of this xture due to the disregard of the information printed in this manual. Only qualied
and/or certied personnel should perform installation of this xture and only the original
rigging parts included with this xture should be used for installation. Any modications
to the xture and/or the included mounting hardware will void the original manufacturer’s
warranty and increase the risk of damage and/or personal injury.
PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR
MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE
MANUFACTURE’S WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE FIXTURE TO RAIN AND MOISTURE!
MINIMUM DISTANCE TO OBJECTS/SURFACES
MUST BE 6.6 FEET (2 METERS)
MAXIMUM TEMP OF EXTERNAL SURFACE 185° F (85°C)
MINIMUM DISTANCE OF INFLAMMABLE MATERIALS
FROM THE SURFACE 1.6 FEET (0.5 METER)
15.0 m
15.0

7
SAFETY GUIDELINES
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET
UV RADIATION! FIXTURE EMITS HIGH INTENSITY
WAVELENGTH OF ULTRAVIOLET UV LIGHT FROM THE UV
COLOR FILTER. WEAR PROPER EYE AND SKIN
PROTECTION. AVOID PROLONGED PERIODS OF
EXPOSURE TO UV COLOR FILTER. AVOID WEARING
WHITE COLOR CLOTHING AND/OR USING UV PAINTS ON
SKIN. AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT
DISTANCES LESS THAN 11 feet (3.3m). DO NOT OPERATE
FIXTURE WITH DAMAGED/MISSING EXTERNAL COVERS.
DO NOT LOOK DIRECTLY INTO THE UV LIGHT AND/OR
VIEW UV LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS
THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT. INDIVIDUALS SUFFERING
FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DIS-ORDERS, OR
INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT IF
EXPOSED TO THE ULTRAVIOLET UV LIGHT EMITTED FROM THE UV LED.
DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow
approximately 60 minutes for the xture to cool down before serving.
DO NOT shake xture, avoid brute force when installing and/or operating xture.
DO NOT operate xture if the power cord is frayed, crimped, damaged and/or if any of the
power cord connectors are damaged and do not insert into the xture securely with ease.
NEVER force a power cord connector into the xture. If the power cord or any of its connectors
are damaged, replace it immediately with a new one of similar power rating.
DO NOT block any air ventilation slots.
All fan and air inlets must remain clean and never blocked.
Allow approx. 6” (15cm) between xture and other devices or a wall for proper cooling.
When installing xture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, and always install xture with an appropriately rated safety cable.
Always disconnect xture from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by
tugging the wire portion of the cord.
During the initial operation of this xture, a light smoke or smell may emit from the interior of the
xture. This is a normal process and is caused by excess paint in the interior of the casing burning
o from the heat associated with the lamp and will decrease gradually over time.
Consistent operational breaks will ensure xture will function properly for many years.
ONLY Use original packaging and materials to transport the xture in for service.

8
DISCHARGE LAMP WARNING
This xture is tted with a DISCHARGE LAMP, which is highly susceptible to
damage if improperly handled. NEVER touch the lamp with your bare hands, as
the oil from your hands will shorten the life of the lamp. NEVER move the xture
until the lamp has had ample time to cool. DISCHARGE LAMPS are NOT
covered under warranty conditions. Avoid switching the xture ON and OFF
repeatedly in short intervals, as this will reduce lamp life and intensity. To
achieve the intensity associated with discharge lamps, these lamps use gas
sealed in a high-pressure environment to emit a brilliant output.
Due to the high pressure involved with the construction of the lamp, it MAY
EXPLODE DURING PROLONGED EXTENSIVE USE. This risk is increased with age; added
care is encouraged when dealing with older lamps. Thus, the lamp must always be replaced at
the end of their recommended duty cycle. Extreme caution should be used when operating this
or any xture tted with a gas discharge lamp.
UV RADIATION NOTICE
THIS FIXTURE EMITS INTENSE UV RADIATION, WHICH IS HARMFUL TO THE
EYES AND SKIN. THE INTENSE LUMINESCENCE OF THE LAMP CAN CAUSE
SEVERE DAMAGE TO THE RETINA. NEVER OPERATE THIS FIXTURE WITH
ANY OF THE PROTECTIVE COVERS REMOVED. THESE COVERS HAVE BEEN
SPECIALLY DESIGNED TO SHIELD AGAINST UV RADIATION.
LAMP REPLACEMENT
USE ONLY GENUINE ORIGINAL PHILIPS™ LAMPS. OTHER BRAND LAMPS
WILL CAUSE DAMAGE AND WILL VOID FIXTURE WARRANTY!
DISCONNECT THE MAIN POWER SUPPLY BEFORE REPLACING LAMP!
FIXTURE MUST COOL FOR 60 minutes BEFORE REPLACING LAMP!
NEVER TOUCH LAMP WITH BARE HANDS, ALWAYS WEAR GLOVES!
OIL FROM HANDS WILL SHORTEN LIFE OF LAMP!
MAKE SURE ALL COVERS/FIXTURES ARE REPLACED/SECURED BEFORE
OPERATING FIXTURE TO PREVENT ANY RISK AND/OR DAMAGE TO EYE
RETINA FROM UV RADIATION EXPOSURE!

9
MAINTENANCE GUIDELINES
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
CLEANING
Frequent cleaning is recommended to ensure proper function, optimized light output, and an
extended life. The frequency of cleaning depends on the environment in which the xture
operates: damp, smoky, or particularly dirty environments can cause greater accumulation of
dirt on the xture’s optics. Clean the external lens surface periodically with a soft cloth to avoid
dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to ensure proper function and extended life.
There are no user serviceable parts inside this xture, please refer all other service issues to an
authorized ADJ service technician. Should you need any spare parts, please order genuine
parts from your local ADJ dealer.
Please refer to the following points during routine inspections:
- A detailed electrical check by an approved electrical engineer every three months, to make
sure the circuit contacts are in good condition in order to prevent overheating.
- Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall.
- Check for any deformations on the housing, color lenses, rigging hardware, and rigging
points (ceiling, suspension, trussing). Deformations in the housing could allow for dust or
liquids to enter into the xture. Damaged rigging points or unsecured rigging could cause
xture to fall and seriously injure a person(s).
- Electric power supply cables must not show any damage, material fatigue, or sediments.
- NEVER remove the ground prong from the power cable.

1 0
Lens
MENU Button
ENTER Button UP Button
5pin DMX IN
Service Port
5pin DMX OUT
Locking Power Output
Locking Power Input
Fuse (T6.3A)
3pin DMX OUT
3pin DMX IN
DOWN Button
System Menu Display
FIXTURE OVERVIEW
Lamp
replacement
fixture
Carrying
Handles

11
COLOR WHEEL
RED ORANGE AQUAMARINE GREEN LIGHT GREEN LAVENDER PINK
LIGHT
YELLOW
MAGENTA CYAN YELLOW 3200k 6000k UV
RED
ORANGE
AQUAMARINE
GREEN
LIGHT
GREEN
LAVENDER
PINK
LIGHT
YELLOW
MAGENTA
CYAN
YELLOW
3200K
6000K
UV

1 2
GOBO WHEEL

1 3
LAMP REPLACEMENT
Please replace the lamp after 2000 Hours, and clear the lamp running time in the menu.
Loosen the two screws and open the xture head covers.
Loosen the screw in the recess.
Lift the lamp out of its recess, disconnect the lamp and replace it with a new Philips MSD
Platinum 12 R LL lamp..

1 4
INSTALLATION GUIDELINES
FLAMMABLE MATERIAL WARNING
Keep xture minimum 5.0 feet (1.5m) away from ammable materials and/or pyrotechnics.
ELECTRICAL CONNECTIONS
A qualied electrician should be used for all electrical connections and/or installations.
USE CAUTION WHEN POWER LINKING OTHER MODEL FIXTURES AS THE POWER
CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER
OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR MAX AMPS.
MINIMUM DISTANCE TO OBJECTS/SURFACES
MUST BE 6.6 FEET (2 METERS)
MINIMUM DISTANCE OF INFLAMMABLE MATERIALS
FROM THE SURFACE 1.6 FEET (0.5 METER)
MAXIMUM TEMPERATURE OF EXTERNAL SURFACE 185° F (85°C)
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
Fixture MUST be installed following all local, national, and country commercial electrical and
construction codes and regulations.
Before rigging/mounting a single xture or multiple xtures to any metal truss/structure or placing the
xture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal
truss/structure or surface is properly certied to safely hold the combined weight of the xture(s),
clamps, cables, and accessories.
Fixture ambient operating temperature range is 14° to 113°F. (-10° to 45°C).
Do not Use xture under or above this temperature.
Fixture(s) should be installed in areas outside walking paths, seating areas, or away from areas were
unauthorized personnel might reach the xture by hand.
NEVER stand directly below the xture(s) when rigging, removing or servicing.
Overhead xture installation must always be secured with a secondary safety attachment, such as an
appropriately rated safety cable.
Allow approximately 60 minutes for the xture to cool down before servicing.
RIGGING
Overhead rigging requires extensive experience, including among others calculating working
load limits, installation material being used, and periodic safety inspection of all installation
material and the xture. If you lack these qualications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
ALWAYS ATTACH AN APPROPRIATELY RATED SAFETY CABLE (NOT INCLUDED) THAT MEETS
ALL LOCAL, NATIONAL, AND COUNTRY CODES AND REGULATIONS WHENEVER INSTALLING
FIXTURE IN A SUSPENDED ENVIRONMENT!

1 5
INSTALLATION GUIDELINES
OMEGA BRACKETS INSTALLATION
Insert the Omega Brackets into the matching holes on the bottom of the xture. Secure the
Omega Brackets to the xture by turning each quick-lock fastener ¼ turn clockwise; making
sure the fastener is completely locked. Omega Brackets can be installed into the xture base
as illustrated below.
CLAMP INSTALLATION
When mounting xture to truss, be sure to secure an appropriately rated professional grade
rigging clamp to the included Omega Brackets using an M10 screw tted through the center
hole of the Omega Brackets. The xture provides built-in rigging points for a SAFETY CABLE
(not included). Be sure to only use one of the designated rigging points for the safety cable and
never secure a safety cable to a carrying handle.
SAFETY CABLE
ALWAYS ATTACH A SAFETY
WHENEVER INSTALLING THIS
FIXTURE IN A SUSPENDED
ENVIRONMENT TO ENSURE
THE FIXTURE WILL NOT FALL
IF THE CLAMP FAILS.
Clamp
Omega Bracket
Safety Cable

1 6
INSTALLATION GUIDELINES
RIGGING
Overhead rigging requires extensive experience, including among others, calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the xture. If you lack these qualications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
This xture is designed to be mounted vertically (hanging or upright), or horizontally
(perpendicular to vertical axis) only.

1 7
INSTALLATION GUIDELINES
POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT
BEAMS
External sources of light beams from direct sunlight, lighting moving head xtures, and lasers,
which are focused directly towards the exterior housing and/or penetrate the front lens opening
of ADJ lighting xtures, can cause severe internal damage including burning to optics, dichroic
color lters, glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters,
motors, belts, wiring, discharge lamps, and LEDs.
This issue is not specic to ADJ lighting xtures, it is a common issue with lighting xtures from
all manufacturers. Although there is no true way to fully prevent this issue from happening, the
following guidelines can prevent any potential damage from occurring if followed. Contact ADJ
Service for more details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS
FROM DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS
WHILE UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO
NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS
ANOTHER.

1 8
SYSTEM MENU
The xture includes an easy to navigate system menu. The control panel located on the front of
the xture provides access to the main system menu, and is where all necessary system
adjustments are made to the xture. During normal operation, pressing MENU button once will
access the xture’s main menu. Once in the main menu you can navigate through the dierent
functions and access the sub-menus with the UP and DOWN buttons. Once you reach a eld
that requires adjusting, press ENTER button to activate that eld and Use UP and DOWN
buttons to adjust eld. Pressing the ENTER button once more will conrm your setting. You may
exit the main menu at any time without making any adjustments by pressing the MENU button.
To access the LCD Menu Control Display via the internal battery, press and hold the MENU
button for 1 second. The LCD Menu Control Display will automatically shut OFF and exit the
system menu after 15 minutes (to toggle hibernation mode on or o, or change hibernation
timer, select Personality / Status Settings / Hibernation).

1 9
ADJ VIZI BEAM 12RX - SYSTEM MENU
Default setting shown in bold
Supports Software Versions: 1.2
MAIN MENU OPTIONS / VALUES (Default Settings in BOLD)DESCRIPTION
DMX Settings
DMX Address 001 - 512
Shall be used to set the units starting DMX address
channel. Depending on set DMX mode, unit shall
not allow to be addressed any higher that will not
allow for all channels to be accessed from the
console.
DMX Channel Mode 13ch, 17ch Shall be used to set the units desired DMX mode.
No DMX Status
Hold Last
Shall be used to set the units behavior when DMX
signal is not present. Hold shall be the default
setting and unit shall hold all last channel values
received from the console when signal is lost.
Blackout Blackout option shall take all channels to zero (0)
when signal is lost.
Manual
Manual Settings option shall take all channels to
the last set Manual channel settings when signal is
lost.
Personality
Status Settings
Pan Invert ON / OFF
Tilt Invert ON / OFF
P./T. Feedback ON / OFF
P./T. Feedback Speed 1, Speed 2
Hibernation OFF, 01M~99M, 15M
When DMX signal is not present for the set time,
the unit shall go into standby mode after the set
time. When set to OFF, unit shall never go into
hibernation mode. The unit should have 01M to
99M options… so 01M, 02M, 03M… 99M
(M=Minutes). 15M should be default.
Reset Motors
Reset All Motors YES / NO
Pan/Tilt Reset YES / NO
Color Reset YES / NO
Gobo Reset YES / NO
Frost Reset YES / NO
Prism Reset YES / NO
Display
Intensity 1-10
Display Invert YES / NO
Screen Saver
Delay OFF - 10 minutes
Service
Eect Adjust
(Calibration)
Pan 128-127
Eects adjustments (Passcode = 050). Do not
adjust eect settings when performing a factory
reset at the same time.
Tilt 128-127
Color 000-255
…
Shutter 000-255
USB Port Power ON / OFF
Update Software YES / NO
Factory Restore YES / NO Reset to factory default
SYSTEM MENU

2 0
MAIN MENU OPTIONS / VALUES (Default Settings in BOLD)DESCRIPTION
Manual Pan, Tilt, Color, Gobo, Prism1, Prism2, RPrism,
Shutter, Dimmer, Focus, Frost 000-255 Set Manual Control values remain set when no DMX signal is present, including through a power cycle.
Information
Fixture Life Time
Power On Time xxxxxx Hours Total hrs. xture powered ON. Cannot be reset.
P- On Time- R xxxxxx Hours Hours xture powered ON. Can be reset
P- On Time Reset Passcode Reset Power On Time (Passcode = 050)
Total Lamp Time
Lamp On Time xxxxxx Hours Resets to 0 when lamp replaced and reset
(Passcode = 050)
Lamp ON Time-R xxxxxx Hours
Lamp On Time Reset Passcode
Fixture Temps
Head
Current xxx F°/xxx C° Current xture temperature in
Max
Resettable xxx F°/xxx C° Maximum temperature reached since last reset. Can be reset
Max Not
Resettable xxx F°/xxx C° Maximum temperature xture reached. Cannot be reset
Reset Head Temp Passcode
Shall allow for Head Temperature data to be reset.
Should be Passcode protected. Passcode should
be 050.
Fan Info.(RPM)
B_Fan 1: xxxx
Displays fan RPM
B_Fan 2: xxxx
H_Fan 1: xxxx
H_Fan 2: xxxx
H_Fan 3: xxxx
DMX Values
Pan, Pan Fine, Tilt, Tilt Fine, Color,
Gobo, Prism1, Prism2, RPrism,
Shutter, Dimmer, Focus, Focus
Fine, Frost, P/T Speed, Spe. Func
000-255 Displays current DMX Channel value of respective
xture trait.
Error Logs Fixture Errors Displays Fixture Errors
Reset Error Log Reset Error Log (Passcode = 050.
Software Version V1.2 Displays current software version
Lamp Control
Lamp On/O ON / OFF Manual ON/OFF lamp control
Lamp On with
Power ON / OFF Controls lamp ON/OFF during power up
Lamp On via DMX ON / OFF Allows lamp ON via DMX
Lamp O via DMX ON / OFF Allows lamp OFF via DMX
DMX Settings
Select DMX Settings, and press ENTER button to conrm. Use UP/DOWN buttons to select
DMX Address,DMX CH Mode, or No DMX Status.
DMX Address — DMX512 address setting
Select DMX Address, and press ENTER button to conrm. Use UP/DOWN buttons to
adjust address from 001 to 512, and press ENTER button to store.
DMX CH Mode — channel mode
Select DMX CH Mode, and press ENTER button to conrm. Use UP/DOWN buttons to
select 13ch or 17ch, and press ENTER button to store.
No DMX Status — xture state while DMX single stops
Select No DMX Status, and press ENTER button to conrm. Use UP/DOWN buttons to
select Hold Last (If DMX signal stops, xture continues to obey the last command it
received Via DMX), Blackout (xture blacks-out if DMX signal stops) or Manual (If DMX
signal stops, xture returns all channels to the last setting entered manually), and press
ENTER button to store.
In the Blackout /Hold Last state, and with no DMX signal, the unit will remain in the nal
state for 15M before reverting to static mode. At this time, the lamp and motors will turn-
o. When the DMX signal is reconnected, the unit will automatically activate and reset.