ADJ H2O DMX PRO User manual

Introduction:
Thank you for purchasing the H2O DMX PRO by American DJ®. The
H2O DMX PRO is an improvement of the very popular H2O LED. This
new unit has better optics and brighter LED output producing vibrant
colors. The unit has 2 operating modes; manual mode & DMX Con-
trolled. It can be used as a stand alone unit or in a master-slave con-
figuration. This unit is suitable for theaters, studios, retail stores, and
other similar locations.
Unpacking: Every H2O DMX PRO has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping. If
the carton appears to be damaged, carefully inspect your units for any
damage and be sure all accessories necessary to operate the system
have arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for fur-
ther instructions. Please do not return the system to your dealer with-
out rst contacting customer support.
Customer Support:
American DJ®provides a toll free customer support line, to provide set
up help and to answer any question should you encounter problems
during your set up or initial operation. You may also visit us on the web
at www.americandj.com for any comments or suggestions. Service
Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Stan-
dard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
American DJ.
Please recycle the shipping cartoon when ever possible.
H2O DMX PRO Introduction
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 2
Rev. 4/14
User Instructions

H2O DMX PRO Warranty Registration
The H2O DMX PRO carries a two year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) num-
ber. The R.A. number must be clearly written on the outside of the
return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included
in the shipping container. If the unit is under warranty, you must pro-
vide a copy of your proof of purchase invoice. You may obtain a R.A.
number by contacting customer support at [phone].
H2O DMX PRO Features
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
H2O DMX PRO General Instructions
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 3 ©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 4
• Includes Built-In Hanging Yoke
• 5 Colors Plus White
• Mixed Coloring
• Manually Control Color, Rotation Speed, & Dimmer. See page 9.
• 34 Degree Lens & 52 Degree Lens
• Power Cord Daisy Chain (See page 14)
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 14 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
ding amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel
when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
H2O DMX PRO Safety Precautions
H2O DMX PRO Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.

©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 5 ©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 6
Power Supply: The American DJ®H2O DMX PRO contains a auto-
matic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a sin-
gle controller, as long as all xtures and the controller are DMX com-
pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The H2O DMX PRO is a three channel DMX unit. The DMX address is set
on the top panel of the H2O DMX PRO. Your unit and your DMX con-
troller require a approved DMX-512 110 Ohm Data cable for data input
and data output. We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
be daisy chained and cannot be split.
Figure 1
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground 1 Ground
XLR Male Socket
XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
H2O DMX PRO DMX Set Up H2O DMX PRO DMX Set Up

©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 7
H2O DMX PRO System Menu
On-Board System Menu. The H2O DMX PRO comes with an easy
to navigate system menu. This next section will detail the functions of
each command in the system menu. Please read the next section
thoroughly!
To access the main menu press the MENU button. Press the UP or
DOWN buttons until you reach function you wish to change. When you
reach the function you wish to change press the ENTER button. When
a function is selected use the UP or DOWN buttons to change the func-
tion settings. Once your changes are made press the ENTER button,
and then press and hold the MENU button for at least three seconds
to conrm and lock the change into the system memory. If the MENU
button is not pressed and held within eight seconds the xture will
automatically conrm and lock the change into the system memory. To
exit without making any changes press the MENU button.
H2O DMX PRO System Menu
ADDR - DMX Address Setting via control board -
1. Press the MENU button until “ADDR” is displayed, press
ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to nd your desired address.
3. Press ENTER to conrm, then connect your DMX controller.
SLND - This will let you set unit as a master or a slave in a
master/slave conguration.
1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “MAST” or “SL 1” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to conm.
LED - With this function the LED display will turn off after 2
minutes.
1. Press the MENU button until “LED” is displayed, press
ENTER.
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 8

H2O DMX PRO System Menu
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to allow the LED display to turn o after 2 min-
utes. Press any button to turn on the LED display again.
3. Press ENTER, and then press and hold the MENU button for at
least three seconds to conrm.
DISP - This will “ip” the LED display
1. Press the MENU button until “DISP” is displayed, press
ENTER.
2. Either “dISP” or “dSIP” will now be displayed. Press the UP or
DOWN buttons to select one or the other.
3. Press ENTER, and then press and hold the MENU button for at
least three seconds to conrm.
MANU - This function will let you manually test the color
wheel, water wave, and dimmer. In this function you can
also manually adjust and set the color wheel, rotation
speed, and dimmer.
1. Press the MENU button until “MANU” is displayed, press
ENTER.
2. Use the UP or DOWN buttons to scroll between “COLO”
(Color), “WAVE” (Water Wave), or “DIMM” (Dimmer). Select the
function you would like to test and press ENTER.
3. Use the UP or DOWN buttons to adjust the values to test/
check the function. Press the MENU button after testing the
functions.
If you would set your desired color, rotation speed, and dimmer,
press the ENTER button after each submenu is adjusted.
Example: “COLO” is displayed, press ENTER. Make your
adjustments using the UP or DOWN buttons until your desired
color projected. After you have found your desired color, press
ENTER. Scroll to the next function, adjust, and press ENTER.
4. After you have made your desired settings press and hold the
MENU button for at least 3 seconds.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
2. The xture will now run a self test. Press the MENU button to
exit.
FHRS - With this function you can display the running time
of the unit.
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The running time of the xture will now be displayed. Press
the MENU button to exit.
VER - This will display the software version
1. Press the MENU button until “VER” is displayed. Press the
ENTER button and the software vesion will be displayed.
2. Press the MENU button to exit.
RSET - This will display the software version
1. Press the MENU button until “RSET” is displayed. Press the
ENTER button and the unit will reset itself.
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 9 ©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 10
H2O DMX PRO System Menu

H2O DMX PRO DMX Control
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the individual lasers, rotation
and macros. A DMX controller allows you to create unique programs
tailored to your individual needs.
1. The Hypnotic RGB is a 3 channel DMX fixture. See page 12 for
detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-6 as well as the set-up specifications that are includ-
ed with your DMX controller. Follow the instructions on page 8 to
set the DMX address.
3. Use the controller’s faders to control the various DMX fixture traits.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
5. For help operating in DMX mode consult the manual included
with your DMX controller.
Focusing Lens: The lens can be focused by turning it clockwise or
counter-clockwise to focus the lens to your desire.
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 11 ©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 12
Channel Value Function
1 MASTER DIMMER
1 - 255 0% - 100%
2 ROTATION
0 - 9 NO ROTATION
10 - 120 CLOCKWISE ROTATION FAST - SLOW
121 - 134 NO ROTATION
135 - 245 COUNTER-CLOCKWISE SLOW - FAST
246 - 255 NO ROTATION
3 COLOR
0 - 10 WHITE
11 - 21 WHITE & ORANGE
22 - 32 ORANGE
33 - 43 ORANGE & GREEN
44 - 54 GREEN
55 - 65 GREEN & BLUE
66 - 76 BLUE
77 - 87 BLUE & YELLOW
88 - 98 YELLOW
99 - 109 YELLOW & PURPLE
110 - 120 PURPLE
121 - 127 PURPLE & WHITE
128 - 186 CLOCKWISE COLOR ROTATION
FAST - SLOW
187 - 196 STOP
197 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
H2O DMX PRO DMX Values & Traits
H2O DMX PRO Master-Slave Configuration
Master-Slave Conguration This function will allow you to link up
to 16 units together and operate without a controller. In Master-Slave
operation one unit will act as the controlling unit and the others will
react to the controlling units programs. Any unit can act as a Master or
as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit press the MENU button until “SLND” is dis-
played, and press ENTER. Press the UP or DOWN buttons so that
“MAST” is displayed and press ENTER.
3. On the slave units press the MENU button until “SLND” is dis-
played, and press ENTER. Press the UP or DOWN buttons so that
“SL 1” is displayed and press ENTER.
4. The slave units will now follow the Master unit.
H2O DMX PRO UC3 Control

H2O DMX PRO 34 Degree Lens Install
The install of the 34 Degree lens
is a pretty easy process. Please
be very carefull when doing this
install.
Unscrew and remove the focus
lens. Using your thumb, gently
push the lens outward until it
“pops” out.
When the lens “pops” out, the pic-
ture to the left is what you should
see. Remove the lens and retainer
ring.
Flip the focus lens barrel over and
insert the 34 degree lens. Care-
fully insert the retainer ring. Please
do this very carefully. Make sure
retainer ring is in correctly, esh
against the lens. Now you can
screw the focus lens back into the
H2O DMX PRO.
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 6 xtures maximum. After 6 xtures you will need to
use a new power outlet. They must be the same xtures. DO NOT
mix xtures.
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 14©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 13
H2O DMX PRO Power Cord Daisy Chain
H2O DMX PRO Fuse Replacement
Fuse Replacement: Locate and remove the unit’s power cord. Once
the cord has been removed located the fuse holder located inside the
power socket. Insert a flat-head screw driver into the power socket and
gently pry out the fuse holder. Remove the bad fuse and replace with a
new one. The fuse holder has a built-in socket for a spare fuse be sure
not to confuse the spare fuse with active fuse.
Warning: If after replacing the fuse you continue to blow fuses, STOP
using the unit. Contact customer support for further instructions. Con-
tinuing to use the unit may cause serious damage.
Trouble Shooting: Listed below is a problem that you may encounter,
with a solution.
No light output from the unit;
1. Be sure the fuse has not blown. The fuse is located on the rear
panel inside the power socket. See Fuse Replacement.
H2O DMX PRO Trouble Shooting
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external lenses should be carried out periodically to opti-
mize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Clean the external optics with glass cleaner and a soft cloth every
20 days.
3. Always be sure to dry all parts completely before plugging the
unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-
mend cleaning on a monthly basis. Periodic cleaning will ensure lon-
gevity, and crisp beam output.
H2O DMX PRO Cleaning

H2O DMX PRO Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specic warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by ac-
ceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modied in any manner which American DJ, Inc. concludes, after inspection, aects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specied above, American DJ, Inc. will replace defec-
tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility of
American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of American DJ. All products covered by this war-
ranty were manufactured after January 1, 1990, and bear identifying marks to that eect.
E. American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or tness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or tness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to American DJ and American Audio
Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli-
ers)
• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Eect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 2-year (730 day) Limited Warranty (excluding motors which have a
1-year (365 day Limited Warranty)
©American DJ Supply®- www.americandj.com - H2O DMX PRO Instruction Manual Page 15
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
American DJ®
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: [phone] / Fax: [phone]
Web: www.americandj.com / E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: [phone] / Fax: [phone]
MODEL: H2O DMX PRO
VOLTAGE:100V~240V 50/60Hz
LED: 1 X 45W LED
POWER CONSUMPTION: 69W
DIMENSIONS: 11.5"(L) x 8.75"(W) x 4.75"(H)
292 x 236 x 121mm
WEIGHT: 9 Lbs/ 4 Kgs
POWER CORD DAISY CHAIN: 6 Fixtures Max.
FUSE: 7 Amp
WORKING POSITION: Any Safe Position
BEAM ANGLE: 34 Degrees or 52 Degrees
COLORS: 6
WARRANTY: 2 YEARS (730 DAYS)
H2O DMX PRO Specifications
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.