Adj Green phantom User manual

User Instructions

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 2

Unpacking: Thank you for purchasing the Green Phantom™ by

American DJ®. Every Green Phantom™ has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your unit

for any damage and be sure all equipment necessary to operate the

unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return the unit to your dealer without

rst contacting customer support.

Introduction: The Green Phantom™ is a unique two channel, DMX

intellingent green laser effect that creates several different patterns.

This unit can be used as a stand alone, sound-active unit, in a manual

mode or a auto mode. These modes can also be used in a Master/

Slave conguration. The unit can also be controlled via DMX controller.

For best results use fog or special effects smoke to enhance the beams

projections.

Customer Support: American DJ®provides a toll free customer

support line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

ments or suggestions. For service related issue please contact Ameri-

can DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ customer support.

Please recycle the shipping carton when ever possible.

American DJ®

4295 Charter Street

Los Angeles, CA. 90058

www.americandj.com

7/07

Green Phantom™ General Introduction

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 4©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 3

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future

reference.

CAUTION IMPORTANT! When installing this projector, make sure

that it is mounted in a manner that prevents the audience from

looking directly into the beam, and the beam from striking the

audience.

• 4.9mW Green Laser Diode

• Sound Active with Internal Microphone

• DMX-512 Protocol Compatible (Uses Two DMX Channels)

• Master/Slave Operation/Stand Alone/Sound Active, Manual Mode

& Auto Mode

• Pattern & Elapse Time Knob

• Mode Selection Switch

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short. Do not attempt to oper-

ate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 11 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen on, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

Green Phantom™ Warranty Registration

Green Phantom™ Features

Green Phantom™ General Instructions Green Phantom™ Safety Precautions

The Green Phantom™ carries a 90 day limited warranty. Please fill

out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. num-

ber must be clearly written on the outside of the return package. A

brief description of the problem as well as the R.A. number must also

be written down on a piece of paper included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper.

Green Phantom™ Warning Labels

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 6©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 5

CAUTION IMPORTANT! When installing this projector, make sure

that it is mounted in a manner that prevents the audience from

looking directly into the beam, and the beam from striking the

audience.

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Green Phantom™. The American DJ®Green Phantom™ is 120v only.

Because line voltage may vary from venue to venue, you should be

sure your unit voltages matches the wall outlet voltage before attempt-

ing to operate you xture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a sin-

gle controller, as long as all xtures and the controller are DMX com-

pliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Dipswitches in DMX mode: This unit uses dipswitches to assign a

DMX address. Each dipswitch represents a binary value.

Dipswitch 1 address equals 1

Dipswitch 2 address equals 2

Dipswitch 3 address equals 4

Dipswitch 4 address equals 8

Dipswitch 5 address equals 16

Dipswitch 6 address equals 32

Dipswitch 7 address equals 64

Dipswitch 8 address equals 128

Dipswitch 9 address equals 256

Dipswitch 10 - Some units omit dipswitch 10. When a unit does

include dipswitch #10, it is usually used for special functions such as

Green Phantom™ Set Up

sound activation.

Assigning DMX Address: Each dipswitch has a preset value. A spe-

cific DMX address is set by combining the dipswitches that sum your

desired value. For example: To achieve a DMX address of 7, combine

dipswitches 1, 2, and 3. Since dipswitch 1 has a value of 1, dipswitch

2 has a value of 2, and dipswitch 3 has a value of 4, the combination

of the three create a DMX value of 7. (See example below).

Set DMX address 1: Set DMX address 7:

Dip-switches # 1 = 1 Dip-switches # 1 = 1

2 = 2

3 = 4

= 7

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Green Phantom™ can be controlled via DMX-512

protocol. The Green Phantom™ is a two channel DMX unit. The DMX

address is set on the rear panel of the Green Phantom.™ Your unit and

your DMX controller require a standard 3-pin XLR connector for data

input and data output (Figure 1). If you are making your own cables,

be sure to use standard two conductor shielded cable (This cable may

be purchased at almost all pro sound and lighting stores). Your cables

should be made with a male and female XLR connector on either end

of the cable. Also remember that DMX cable must be daisy chained

and can not be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Green Phantom™ Set Up

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 7 ©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 8

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR socket of the last unit

in your daisy chain to terminate the line. Using a cable terminator (ADJ

part number Z-DMX/T) will decrease the possibilities of erratic behav-

ior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Green Phantom™ Set Up

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 9 ©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 10

Power Supply: This unit is available only in 120v. Before plugging

your unit in be sure the source voltage in your area matches the

required voltage for your American DJ®Green Phantom™.

General Operation: This fixture is designed to operate as a stand

alone, sound-active unit, or in a Master/Slave configuration. It can

also operate via DMX controller. The Green Phantom™ is ready to

be plugged in out of the box. The unit comes with several built-in

patterns that automatically cycle through when the unit is operat-

ing, the patterns can also be selected manually. If the unit does not

turn on after the unit has been plugged in, be sure the unit is properly

plugged in to a matching wall outlet. If the problem continues to per-

sist, please contact customer support for further instructions.

Operating Modes:

Universal DMX Control: This mode allows you to use a universal

DMX-512 controller such as the American DJ®DMX Operator™ or

Show Designer.™

1. To control your fixture in DMX mode, follow the set-up procedures

on pages 6 - 8 as well as the set-up procedures included with

your DMX controller.

2. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

3. Assign a DMX address to the unit by following DMX setup and

using dipswitches 1-10.

4. The Green Phantom™ uses two DMX channels. See page 13

for detailed description of the DMX traits. Use your DMX control-

ler to activate the various built-in patterns.

5. For help operating in DMX mode consult the manual included

with your DMX controller.

Stand-Alone Operation (Auto Mode, Manual Mode & Sound

Active Mode): This mode allows a single unit to run in an auto

mode, manual mode, or sound active mode. Use these modes when

running a single unit, or when running several units as individuals.

Auto Mode:

1. Set the mode switch to the “Auto” position. Adjust the Elapse

Time knob to set the speed of pattern switches.

Green Phantom™ Operation Green Phantom™ Operation

Manual Mode:

1. Set the mode switch to the “Manual” position. Use the Pattern

knobs 1 & 2 to adjust the patterns. Stop adjusting when you find

your desired pattern.

Sound Active Mode:

1. Set the mode switch to the “Sound Active” position.

2. The unit will react to the low frequencies of music via the internal

microphone.

Master-Slave Operation (Auto Mode, Manual Mode & Sound

Active Mode): This mode will allow you to link up to 16 units together

and operate without a controller. In Master-Slave operation one unit

will act as the controlling unit and the others will react to the controlling

units programs. Any unit can act as a Master or as a Slave.

1. Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remem-

ber the Male XLR connector is the input and the Female XLR

connector is the output. For longer cable runs we suggest a

terminator at the last fixture.

2. Auto Mode: Choose a unit to function as the Master and set dip-

switch #1 to the “ON” position, and put the Mode switch in “Auto”

position. This unit must be the first unit in line.

3. Turn any other dipswitches to the “ON” position, except dip-

switch #1, this must remain “OFF” on the SLAVE units. Now they

will react the same as the MASTER.

4. Manual Mode: Choose a unit to function as the Master and set

dipswitch #1 to the “ON” position, and put the Mode switch in

“Manual” position. This unit must be the first unit in line.

5. Turn any other dipswitches to the “ON” position, except dip-

switch #1, this must remain “OFF” on the SLAVE units. Now they

will react the same as the MASTER.

6. Sound Active Mode: Choose a unit to function as the Master and

set dipswitch #1 to the “ON” position, and put the Mode switch in

“Sound Active” position. This unit must be the first unit in line.

7. Turn any other dipswitches to the “ON” position, except dip-

switch #1, this must remain “OFF” on the SLAVE units. Now they

will react the same as the MASTER.

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 11 ©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 12

Green Phantom™ Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning

the external lenses should be carried out periodically to optimize light

output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Clean the external optics with glass cleaner and a soft cloth every

20 days.

3. Always be sure to dry all parts completely before plugging the

unit back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-

mend cleaning on a monthly basis. Periodic cleaning will ensure lon-

gevity, and crisp beam output.

Green Phantom™ DMX Traits and Patterns Green Phantom™ Warranty

MANUFACTURER’S LIMITED WARRANTY

A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American

Audio products to be free of manufacturing defects in material and workmanship for a prescribed

period from the date of purchase (see specic warranty period on reverse). This warranty shall be

valid only if the product is purchased within the United States of America, including possessions

and territories. It is the owner’s responsibility to establish the date and place of purchase by ac-

ceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before

sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send

the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the

requested repairs or service (including parts replacement) are within the terms of this warranty,

American DJ, Inc. will pay return shipping charges only to a designated point within the United

States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories

should be shipped with the product. If any accessories are shipped with the product, American DJ,

Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the

safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ, Inc. concludes, after inspection, affects the reliability

of the product; if the product has been repaired or serviced by anyone other than the American DJ,

Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the

product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ, Inc. will replace defec-

tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty

service and repair labor by reason of defects in material or workmanship. The sole responsibility

of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replace-

ment thereof, including parts, at the sole discretion of American DJ. All products covered by this

warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ, Inc. reserves the right to make changes in design and/or improvements

upon its products without any obligation to include these changes in any products theretofore

manufactured. No warranty, whether expressed or implied, is given or made with respect to any

accessory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ, Inc. in connection with this product, including

warranties of merchantability or tness, are limited in duration to the warranty period set forth

above. And no warranties, whether expressed or implied, including warranties of merchantability

or tness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s

sole remedy shall be such repair or replacement as is expressly provided above; and under no

circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,

arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to American DJ and American Audio

Products and supersedes all prior warranties and written descriptions of warranty terms and

conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli-

ers)

• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty

• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty

(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble

Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,

and Star Tec Series)

• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty

• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which

have a 1-year (365 day Limited Warranty)

First unplug the power. The fuse holder is located next to the power

cord. Using a flat-head screw driver unscrew the fuse holder. Remove

the bad fuse and replace with a new one.

Green Phantom™ Fuse Replacement

©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 13 ©American DJ®- www.americandj.com - Green Phantom™ Instruction Manual Page 14