Adjustables E-95MR User manual

99300791-c EDR10782 11/06
OPERATION GUIDE
www.adjustablesbyleggett.com

CONTENTS
E-95MR Function ................................................................................................. 4
J Box Programming Procedure .......................................................................... 5
Power Down Box Operation ..............................................................................5
E-95MR Programming (1 hand control - 1 bed) ................................................ 6
E-95MR Programming (2 hand controls - 1 bed)...............................................7
E-95MR Programming (1 hand control - 2 beds) .............................................. 8
E-95MR Programming (2 hand controls - 2 beds) ............................................. 9
E-95MR Reprogramming (separating 2 beds) ................................................. 10
Copyright © 2006 Leggett & Platt, Inc.

4
E-95MR Hand Control Operation Guide 99300791-c
E-95MR FUNCTION
IMPORTANT INFORMATION
READ ADVISORY INFORMATION IN THE OWNERS MANUAL CAREFULLY BEFORE
USING THIS PRODUCT. THE POTENTIAL FOR ELECTRICAL SHOCK EXISTS IF
ELECTRICAL COMPONENTS ARE NOT INSTALLED OR OPERATED PROPERLY.
TRANSMISSION INDICATOR LIGHT
Verifies a button is being pressed
and data is being sent to the bed.
FLAT BUTTON
Press to return bed to the level
position. To stop the bed while in
motion, press and hold any button
until bed movement ceases. This
button also turns off the
massagers.
SET BUTTON
Press to capture any position or
function of the bed as a
programmed position. Press the
MR button to return the bed to the
custom programmed position.
To Program Set Position:
1. Set the head, foot, massage
and/or wave to the desired
setting.
2. Press and release the set
button.
3. Press and release the MR
button.
HEAD UP/DOWN BUTTON
Press and hold to raise or lower
head section.
HEAD MASSAGE ARROW
BUTTONS
Press and hold to increase or
decrease head massage intensity.
WAVE ARROW BUTTONS
Press and hold—after the head and/
or foot massage, and the wave
system have been activated—to
increase or decrease wave speed.
HEAD MASSAGE ON/OFF
BUTTON
Switches the head massage on or
off. When switched on, the
massage has an automatic shut off
timer of 30 minutes.
WAVE ON/OFF BUTTON
Press—after the head and/or foot
massage have been activated—to
activate or deactivate the wave
vibration system.
MR BUTTON
Press to recall a position or
massage function set by the set
button.
FOOT UP/DOWN BUTTON
Press and hold to raise or lower
foot section.
FOOT MASSAGE ARROW
BUTTONS
Press and hold to increase or
decrease foot massage intensity.
FOOT MASSAGE ON/OFF
BUTTON
Switches the foot massage on or
off. When switched on, the
massage has an automatic shut off
timer of 30 minutes.
HAND CONTROL REQUIRES FOUR (4) AAA SIZE BATTERIES. TO CONSERVE
BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY
BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.
NOTE

E-95MR Hand Control Operation Guide 99300791-c
5
J BOX PROGRAMMING PROCEDURE
When programming the hand control,
unplug the adjustable bed electrical
power cord. Wait 30 seconds, then plug
the cord back in to the power source.
This simple process automatically sets
the bed to the program mode for 90
seconds. For convenience, use this
procedure in lieu of pressing the learn
button (located on the J Box, mounted to
the underside of the bed base frame).
J BOX PROGRAMMING
For adjustable beds equipped with “J box” only—no power down box.
At any point where “press the learn
button” is designated, disconnecting and
reconnecting the electrical power cord
will achieve the same function. Note that
this alternate programming feature is
only applicable to beds without a power
down box. Power down equipped
adjustable beds require use of the learn
button when programming the hand
control.
POWER DOWN BOX OPERATION
In case of a power outage, press and
hold the learn button on the power down
box to lower the bed to the flat position
(FIGURE 1).
This function is only for lowering the bed
and will not operate the bed to any other
position. The (2) 9 volt batteries should
be replaced after this function is used.
In the event the power down feature
does not work, check to make sure the
(2) 9 volt batteries are good.
LEARN
BUTTON
FIGURE 1: Power down box learn button.
POWER
DOWN BOX

6
E-95MR Hand Control Operation Guide 99300791-c
E-95MR PROGRAMMING 1 hand control - 1 bed
The two step procedure below is required to program 1 hand control to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical
outlet. If programming fails, initiate the programming procedure a second time.
STEP 2
On the hand control, simultaneously
press and hold the flat and the head
massage on/off buttons (FIGURE 3). The
transmission indicator light will flash
slowly and then flash rapidly to indicate
programming mode. Continue to hold
for 5 seconds and then release the
buttons.
STEP 1
The bed will be equipped with either a
power down box or J box receiver unit
(FIGURE 2). Locate the receiver unit for
the bed and press the learn button for 1
second and release. Note: If you
experience difficulty locating or reaching
the learn button on a J box equipped
adjustable bed, refer to J Box
Programming on page 5.
J BOX
FIGURE 2: Power down box and J box receiver units.
LEARN
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.
J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.
FLAT BUTTON
TRANSMISSION
INDICATOR LIGHT
FIGURE 3
HEAD MASSAGE
ON/OFF BUTTON
One hand control is now programmed to
operate one bed.

E-95MR Hand Control Operation Guide 99300791-c
7
E-95MR PROGRAMMING 2 hand controls - 1 bed
The three step procedure below is required to program 2 hand controls to operate 1
bed. Before beginning, make certain the bed is plugged into a working grounded
electrical outlet. If programming fails, initiate the programming procedure a second
time.
STEP 2
On hand control 1, simultaneously press
and hold the flat and the head massage
on/off buttons (FIGURE 3). The
transmission indicator light will flash
slowly and then flash rapidly to indicate
programming mode. Continue to hold
for 5 seconds and then release the
buttons.
STEP 1
The bed will be equipped with either a
power down box or J box receiver unit
(FIGURE 2). Locate the receiver unit for
the bed and press the learn button for 1
second and release. Note: If you
experience difficulty locating or reaching
the learn button on a J box equipped
adjustable bed, refer to J Box
Programming on page 5.
J BOX
FIGURE 2: Power down box and J box receiver units.
LEARN
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.
J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.
STEP 3
Repeat Step 1 and Step 2 with hand
control 2.
Two hand controls are now programmed
to operate one bed.
HAND
CONTROL 1
HAND
CONTROL 2
FLAT BUTTON
TRANSMISSION
INDICATOR LIGHT
FIGURE 3
HEAD MASSAGE
ON/OFF BUTTON
NOTE
OPERATE ONLY ONE (1) HAND CONTROL AT
A TIME. OPERATING TWO (2) HAND
CONTROLS AT THE SAME TIME WILL
MOMENTARILY BLOCK BOTH RF SIGNALS
AND PREVENT BOTH CONTROLS FROM
FUNCTIONING.

8
E-95MR Hand Control Operation Guide 99300791-c
E-95MR PROGRAMMING 1 hand control - 2 beds
The three step procedure below is required to program 1 hand control to operate 2
beds. Before beginning, make certain the beds are plugged into a working grounded
electrical outlet. If programming fails, initiate the programming procedure a second
time.
STEP 2
On the hand control, simultaneously
press and hold the flat and the head
massage on/off buttons (FIGURE 3). The
transmission indicator light will flash
slowly and then flash rapidly to indicate
programming mode. Continue to hold
for 5 seconds and then release the
buttons.
STEP 1
The bed will be equipped with either a
power down box or J box receiver unit
(FIGURE 2). Locate the receiver unit for
the bed and press the learn button for 1
second and release. Note: If you
experience difficulty locating or reaching
the learn button on a J box equipped
adjustable bed, refer to J Box
Programming on page 5.
J BOX
FIGURE 2: Power down box and J box receiver units.
LEARN
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.
J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.
STEP 3
Repeat Step 1 and Step 2 for bed 2.
One hand control is now programmed to
operate two beds.
BED 1
BED 2
FLAT BUTTON
TRANSMISSION
INDICATOR LIGHT
FIGURE 3
HEAD MASSAGE
ON/OFF BUTTON

E-95MR Hand Control Operation Guide 99300791-c
9
E-95MR PROGRAMMING 2 hand controls - 2 beds
The six step procedure below is required to program 2 hand controls to operate 2 beds. Before
beginning, make certain the beds are plugged into a working grounded electrical outlet. If
programming fails, initiate the programming procedure a second time.
STEP 1
The bed will be equipped with either a power
down box or J box receiver unit (FIGURE 2).
Locate the receiver unit for bed 1 and press the
learn button for 1 second and release. Note: If
you experience difficulty locating or reaching
the learn button on a J box equipped
adjustable bed, refer to J Box Programming on
page 5.
J BOX
FIGURE 2: Power down box and J box receiver units.
LEARN
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.
J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.
STEP 2
On hand control 1, simultaneously press and
hold the flat and the head massage on/off
buttons (FIGURE 3). The transmission
indicator light will flash slowly and then flash
rapidly to indicate programming mode.
Continue to hold for 5 seconds and then
release the buttons.
STEP 3
Repeat Step 1 and Step 2 with hand control 2.
STEP 4
The bed will be equipped with either a power
down box or J box (FIGURE 2). Locate the
receiver unit for bed 2 and press the learn
button for 1 second and release.
STEP 5
On hand control 1, simultaneously press and
hold the flat and the head massage on/off
buttons (FIGURE 3). The transmission
indicator light will flash slowly and then flash
rapidly to indicate programming mode.
Continue to hold for 5 seconds and then
release the buttons.
STEP 6
Repeat Step 4 and Step 5 with hand control 2.
Two hand controls are now programmed to
operate two beds.
HAND
CONTROL 1
BED 1
HAND
CONTROL 2
BED 2
OPERATE ONLY ONE (1) HAND CONTROL AT
A TIME. OPERATING TWO (2) HAND
CONTROLS AT THE SAME TIME WILL
MOMENTARILY BLOCK BOTH RF SIGNALS
AND PREVENT BOTH CONTROLS FROM
FUNCTIONING.
NOTE
FLAT BUTTON
TRANSMISSION
INDICATOR LIGHT
FIGURE 3
HEAD MASSAGE
ON/OFF BUTTON

10
E-95MR Hand Control Operation Guide 99300791-c
E-95MR REPROGRAMMING separating 2 beds
The six step procedure below is required to separate 2 hand controls from operating 2 beds. One
hand control per bed operation will result. Before beginning, make certain the beds are plugged into
a working grounded electrical outlet. If programming fails, initiate the programming procedure a
second time. NOTE: OPERATE ONLY ONE (1) HAND CONTROL AT A TIME. OPERATING TWO (2) HAND
CONTROLS AT THE SAME TIME WILL MOMENTARILY BLOCK BOTH RF SIGNALS AND PREVENT BOTH
CONTROLS FROM FUNCTIONING.
STEP 4
The bed will be equipped with either a power
down box or J box (FIGURE 2). Locate the
receiver unit for bed 2 and press the learn
button for 1 second and release.
STEP 5
On hand control 2, simultaneously press and
hold the flat and the head massage on/off
buttons (FIGURE 3).The transmission
indicator light will flash slowly and then flash
rapidly to indicate programming mode.
Continue to hold for 5 seconds and then
release the buttons.
STEP 6
Repeat Step 4 and Step 5 with hand control 2.
Independent hand control operation is now
restored (hand control 1 operating bed 1; hand
control 2 operating bed 2).
STEP 2
On hand control 1, simultaneously press and
hold the flat and the head massage on/off
buttons (FIGURE 3). The transmission
indicator light will flash slowly and then flash
rapidly to indicate programming mode.
Continue to hold for 5 seconds and then
release the buttons.
STEP 3
Repeat Step 1 and Step 2 with hand control 1.
Note: wait 90 seconds before proceeding to
Step 4.
STEP 1
The bed will be equipped with either a power
down box or J box receiver unit (FIGURE 2).
Locate the receiver unit for bed 1 and press the
learn button for 1 second and release. Note: If
you experience difficulty locating or reaching
the learn button on a J box equipped
adjustable bed, refer to J Box Programming on
page 5.
BED 1
BED 2
J BOX
FIGURE 2: Power down box and J box receiver units.
LEARN
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.
J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.
HAND CONTROL 1
FLAT BUTTON
TRANSMISSION
INDICATOR LIGHT
FIGURE 3
HEAD MASSAGE
ON/OFF BUTTON
HAND CONTROL 2

www.adjustablesbyleggett.com
For customer care online, email:
[email protected]