ADLINK Technology miniBASE-10R User manual
Leading EDGE COMPUTING
miniBASE-10R
User’s Manual
COM Express Type 10 Reference Carrier Board in Mini-ITX Form Factor
Manual Rev.: 1.1
Revision Date: November 7, 2017
Part Number: 50-1V002-1010
ii Preface
Preface
Copyright
Copyright 2017 ADLINK Technology, Inc. This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in
any form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve reliability, design, and
function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer
be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with
the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic
Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to
ensure that our products, manufacturing processes, components, and raw materials have as little impact on the
environment as possible. When products are at their end of life, our customers are encouraged to dispose of them
in accordance with the product disposal and/or recovery programs prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or
registered trademarks of their respective companies.
Revision History
Revision Description Date By
1.00 Initial release 2015-05-15 JC
1.1 Update functional block diagram, mechanical drawing, board layout, pinouts and
LED info 2017-10-07 JC
miniBASE-10R
Preface iii
Table of Contents
Preface................................................................................................................................ii
List of Figures ....................................................................................................................v
List of Tables.....................................................................................................................vi
1. Introduction................................................................................................................1
2. Features......................................................................................................................3
2.1. Integrated Smart Battery Management System..........................................................3
2.2. Secondary BIOS.........................................................................................................3
2.3. Integrated Debug Port with Single Step Execution.....................................................3
2.4. Onboard Audio............................................................................................................3
2.5. Information LEDs........................................................................................................3
2.6. Power, Reset, Lid and Sleep Switches.......................................................................3
3. Component Locations...............................................................................................5
4. Functional Diagram...................................................................................................7
5. Mechanical Drawing..................................................................................................9
6. Connectors, Pinouts and Jumpers ........................................................................11
6.1. Carrier Board Signals – Type 10 ..............................................................................11
6.2. Connector and Pinout Compatibility .........................................................................12
6.3. Carrier Board Design................................................................................................12
6.4. COM Express Board-to-Board Connectors ..............................................................13
6.5. Display Connectors...................................................................................................15
6.6. LVDS Jumper Settings .............................................................................................17
6.7. Audio Connectors.....................................................................................................18
6.8. Mini PCIe and mSATA Connector............................................................................19
6.9. SATA ........................................................................................................................22
6.10. USB and LAN........................................................................................................23
6.11. Serial Ports............................................................................................................24
6.12. I2C, SMBus and CAN Bus .....................................................................................24
6.13. Fan Connector.......................................................................................................25
6.14. Other Connectors..................................................................................................26
6.15. Other Jumpers.......................................................................................................27
6.16. Power Connectors.................................................................................................28
6.17. Power Jumper Settings .........................................................................................29
7. Secondary BIOS ......................................................................................................31
7.1. SPI Secondary BIOS................................................................................................31
iv Preface
8. Switches, POST and LEDs......................................................................................33
8.1. Switches (S1-S4)......................................................................................................33
8.2. POST........................................................................................................................33
8.3. Indicator LEDs..........................................................................................................34
9. Smart Battery Management System ......................................................................35
9.1. Input Power...............................................................................................................35
9.2. Charger Output Capability........................................................................................35
9.3. Key Characteristics...................................................................................................35
9.4. Battery Settings ........................................................................................................35
9.5. Windows OS Interface..............................................................................................36
Safety Instructions...........................................................................................................37
Getting Service.................................................................................................................38
miniBASE-10R
Preface v
List of Figures
Figure 1: miniBASE-10R Component Locations......................................................................................5
Figure 2: miniBASE-10R Functional Block Diagram................................................................................7
Figure 3: miniBASE-10R Mechanical Drawing.........................................................................................9
Figure 4: Carrier Board Signals - Type 10............................................................................................. 11
miniBASE-10R
Introduction 1
1. Introduction
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution
when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration
projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many
advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project
quantity and last but not least brings your product to the market in no time. The average time to design a carrier
board is less than half the time of a full custom OEM board.
The miniBASE-10R is a Mni-ITX size carrier board. Together with the COM Express Type 10 module of your
choice and off-the-shelf add-on cards, you can quickly emulate the functionality of your desired end product for
software development and hardware verification.
To build a functional prototype of your target system you will need:
zCOM Express Type 10 module
zminiBASE-10R carrier board
zPCI Express based or USB based add on cards
zSATA drive storage or flash disk solution
The miniBASE-10R is compatible with Mini size Type 10 pinout COM Express modules and accommodates up to
one Mini PCIe card, one Mini PCIe/mSATA card slot and one SD card.
The miniBASE-10R integrates a Smart Battery Management System that supports two Smart Batteries and 19V
adapter input. The integrated Smart Battery Management System is compliant with the Smart Battery Manager
Specification and uses the System Management Bus (SMBus) for communications between the battery power
subsystem, Smart Batteries and host system (COM Express module). It is ACPI compliant and provides complete
Smart Battery management under a supported operating system. ADLINK’s COM Express Type 10 modules
feature a BIOS that fully supports all Smart Battery communications using existing interfaces defined in the COM
Express specification and are fully compatible with the integrated Smart Battery Management System. The
integrated Smart Battery Management System is a proof-of-concept battery power subsystem that allows for quick
development and integration of battery power into a COM Express system in the following ways:
zTo emulate the battery power subsystem functionality of your prototype system during the design phase
zAs a ready-made battery power subsystem for your customized system
zAs a reference design to integrate a battery power subsystem into your custom-designed carrier
The miniBASE-10R is based on the PICMG COM Express (COM.0 Rev. 2.1) specification and follows the PICMG
COM Express Carrier Design Guide (CDG) where possible (see 6.3 Carrier Board Designon page 12)
2 Introduction
This page intentionally left blank.
miniBASE-10R
Features 3
2. Features
2.1. Integrated Smart Battery Management System
The miniBASE-10R integrates a Smart Battery Management System that support Dual Smart Batteries and 19V
adapter. The Smart Battery Magagement System is a proof-of-concept battery power system that allows for quick
development and integration of battery power into a COM Express system.
The Smart Battery Management System use the SM Bus for communications between battery power system,
Smart Batteries and COM Express module. It is ACPI compliant and provides complete battery management under
a supporting operating system.
Note: The selected COM Express module for miniBASE-10R must support wide voltage range input. (5.7V - 14V),
even if Smart Battery power is not used.
2.2. Secondary BIOS
The miniBASE-10R supports the Serial Peripheral Interface (SPI) for COM Rev. 2.1 modules. Selection of active
BIOS can be made by jumper settings. The jumper of the secondary BIOS is JPX7.
2.3. Integrated Debug Port with Single Step Execution
In addition to a two-digit POST code display, the board also provides a four-digit address display. By jumper
selection the board can be switched into single step BIOS execution mode. Steps are executed using a manually
operated onboard mini switch.
2.4. Onboard Audio
The miniBASE-10R has a Realtek ALC262 audio codec onboard. Audio I/O is provided by a three-jack connector.
2.5. Indicator LEDs
General information is obtained through indicator LEDs for power status, drive activity, and Mini PCIe card type
(WWAN or WLAN). See 8.3 Indicator LEDs on page 34.
2.6. Power, Reset, Lid and Sleep Switches
The miniBASE-10R is equipped four mini switches (S1-4) for Reset, Power and COM.0 Rev.2.1 specified "Lid" and
"Sleep" functions.
4 Features
This page intentionally left blank.
6 Component Locations
This page intentionally left blank.
miniBASE-10R
Functional Diagram 7
4. Functional Diagram
12V or 14V
(with JPY2)
GPIO
NXP
PCA9535
Audio
Codec
ALC262
LAN
i210IT
AB
DB9
COM1
RJ-45
2-ports
USB 2.0
USB0
USB_SS0
USB1
USB_SS1
USB2
USB3
GbE
2-ports
USB 3.0
USB7 Mini USB
USB4
PCIE1 (x1)
DDI0
DP Port
SATA0 SATA
HD Audio
MIC
Line IN
Line OUT
S/PDIF OUT
SMbus
SDIO /
MMC
LVDS / eDP
30-pin
header
Mini
PCie
PCIE0 (x1)
USB5
Mini
PCIe
SATA
PCIE2 (x1)
RJ-45
SER0
POST 80H
SDIO
8-pin
header
DB9
COM2 SER1
SPI
Container SPI
SATA1 Auto
Switch
SATA1
CPLD
Main Input
19VDC
BAT1 (5.7-8.4V with 2 cell)
(9V-12.6V with 3 cell)
LVDS Backlight
3.3 or 5VDC
Smart Battery
(2/3 cell)
Fan Power
5VDC
LVDS VDD
5VDC
SATA Power
5VDC
Power Connectors
Mode detect
LPC
LTC3867
Charger
LTC1760
Smart Battery
(2/3 cell) BAT2 (5.7-8.4V with 2 cell)
(9V-12.6V with 3 cell)
Figure 2: miniBASE-10R Functional Block Diagram
8 Functional Diagram
This page intentionally left blank.
miniBASE-10R
Mechanical Drawing 9
5. Mechanical Drawing
0
0
5.08
145.09
5.08
54.1
130.1
136.99
64.3
88.5
97.95
122.1
5
136.9
9
24.29
71.29
146.3
9
5.08
145.0
9
5.08
150.17
142.07
All dimensions are shown in millimeters.
Tolerances should be ± 0.25mm, unless otherwise noted.The tolerances on the PCB corner locating peg
holes (dimensions [5.08, 5.08], [145.09, 5.08], [5.08, 136.99] and [145.09, 136.99]) should be ± 0.10mm.
Figure 3: miniBASE-10R Mechanical Drawing
10 Mechanical Drawing
This page intentionally left blank.
miniBASE-10R
Connectors, Pinouts and Jumpers 11
6. Connectors, Pinouts and Jumpers
6.1. Carrier Board Signals – Type 10
Figure 4: Carrier Board Signals - Type 10
12 Connectors, Pinouts and Jumpers
6.2. Connector and Pinout Compatibility
Connectors positions and pinouts comply with pinout and signal descriptions in the “PICMG® COM.0 - COM
Express Module Base specification, Revision 2”. This document includes: description of pinouts, signal descriptions
and mechanical characteristics of the COM Express specification. The miniBASE-10R is compatible with COM
Express modules in mini size form factor, Type 10 pinout, COM.0 Rev. 2.1.
6.3. Carrier Board Design
The miniBASE-10R follows the PICMG COM Express Carrier Design Guide (CDG) where possible. The miniBASE-
10R design and schematics are fully verified, and we recommend that you follow them as a reference for your
carrier board design. miniBASE-10R Schematics and Mechanical files as well as the CDG can be downloaded from
the miniBASE-10R product webpage: http://www.adlinktech.com/PD/web/PD_detail.php?cKind=&pid=1362
miniBASE-10R
Connectors, Pinouts and Jumpers 13
6.4. COM Express Board-to-Board Connectors
Signals and Pinout comply with
COM Express Type 10
COM.0 Type 10 rev. 2.1
Pin Row A Row B
1 GND(FIXED) GND(FIXED)
2 GBE0_MDI3- GBE0_ACT#
3 GBE0_MDI3+ LPC_FRAME#
4 GBE0_LINK100# LPC_AD0
5 GBE0_LINK1000# LPC_AD1
6 GBE0_MDI2- LPC_AD2
7 GBE0_MDI2+ LPC_AD3
8 GBE0_LINK# LPC_DRQ0#
9 GBE0_MDI1- LPC_DRQ1#
10 GBE0_MDI1+ LPC_CLK
11 GND(FIXED) GND(FIXED)
12 GBE0_MDI0- PWRBTN#
13 GBE0_MDI0+ SMB_CK
14 GBE0_CTREF SMB_DAT
15 SUS_S3# SMB_ALERT#
16 SATA0_TX+ SATA1_TX+
17 SATA0_TX- SATA1_TX-
18 SUS_S4# SUS_STAT#
19 SATA0_RX+ SATA1_RX+
20 SATA0_RX- SATA1_RX-
21 GND(FIXED) GND(FIXED)
22 USB_SSRX0- USB_SSTX0-
23 USB_SSRX0+ USB_SSTX0+
24 SUS_S5# PWR_OK
25 USB_SSRX1- USB_SSTX1-
26 USB_SSRX1+ USB_SSTX1+
27 BATLOW# WDT
28 (S)ATA_ACT# AC/HDA_SDIN2
29 AC/HDA_SYNC AC/HDA_SDIN1
30 AC/HDA_RST# AC/HDA_SDIN0
31 GND(FIXED) GND(FIXED)
32 AC/HDA_BITCLK SPKR
33 AC/HDA_SDOUT I2C_CK
34 BIOS_DIS0# I2C_DAT
35 THRMTRIP# THRM#
36 USB6- USB7-
37 USB6+ USB7+
38 USB_6_7_OC# USB_4_5_OC#
39 USB4- USB5-
40 USB4+ USB5+
41 GND(FIXED) GND(FIXED)
42 USB2- USB3-
43 USB2+ USB3+
44 USB_2_3_OC# USB_0_1_OC#
45 USB0- USB1-
46 USB0+ USB1+
47 VCC_RTC EXCD1_PERST#
48 EXCD0_PERST# EXCD1_CPPE#
49 EXCD0_CPPE# SYS_RESET#
50 LPC_SERIRQ CB_RESET#
51 GND(FIXED) GND(FIXED)
A B
A1
B1
A110
B110
14 Connectors, Pinouts and Jumpers
COM.0 Type 10 rev. 2.1
Pin Row A Row B
52 RSVD RSVD
53 RSVD RSVD
54 GPI0 GPO1
55 RSVD RSVD
56 RSVD RSVD
57 GND GPO2
58 PCIE_TX3+ PCIE_RX3+
59 PCIE_TX3- PCIE_RX3-
60 GND(FIXED) GND(FIXED)
61 PCIE_TX2+ PCIE_RX2+
62 PCIE_TX2- PCIE_RX2-
63 GPI1 GPO3
64 PCIE_TX1+ PCIE_RX1+
65 PCIE_TX1- PCIE_RX1-
66 GND WAKE0#
67 GPI2 WAKE1#
68 PCIE_TX0+ PCIE_RX0+
69 PCIE_TX0- PCIE_RX0-
70 GND(FIXED) GND(FIXED)
71 LVDS_A0+ / eDP_TX2+ DDI0_PAIR0+
72 LVDS_A0- / eDP_TX2- DDI0_PAIR0-
73 LVDS_A1+ / eDP_TX1+ DDI0_PAIR1+
74 LVDS_A1- / eDP_TX1- DDI0_PAIR1-
75 LVDS_A2+ / eDP_TX0+ DDI0_PAIR2+
76 LVDS_A2- / eDP_TX0- DDI0_PAIR2-
77 LVDS_/eDP_VDD_EN DDI0_PAIR4+
78 LVDS_A3+ DDI0_PAIR4-
79 LVDS_A3- LVDS_/eDP_BKLT_EN
80 GND(FIXED) GND(FIXED)
81 LVDS_A_CK+ / eDP_TX3+ DDI0_PAIR3+
82 LVDS_A_CK- / eDP_TX3- DDI0_PAIR3-
83 LVDS_I2C_CK / eDP_AUX+ LVDS_/eDP_BKLT_CTRL
84 LVDS_I2C_DAT / eDP_AUX- VCC_5V_SBY
85 GPI3 VCC_5V_SBY
86 RSVD VCC_5V_SBY
87 eDP_HPD VCC_5V_SBY
88 PCIE_CLK_REF+ BIOS_DIS1#
89 PCIE_CLK_REF- DD0_HPD
90 GND(FIXED) GND(FIXED)
91 SPI_POWER DDI0_PAIR5+
92 SPI_MISO DDI0_PAIR5-
93 GPO0 DDI0_PAIR6+
94 SPI_CLK DDI0_PAIR6-
95 SPI_MOSI DDI0_DDC_AUX_SEL
96 TPM_PP USB_HOST_PRSNT
97 TYPE10# SPI_CS#
98 SER0_TX DDI0_CTRLCLK_AUX+
99 SER0_RX DDI0_CTRLDATA_AUX-
100 GND(FIXED) GND(FIXED)
101 SER1_TX / CAN_TX FAN_PWMOUT
102 SER1_RX / CAN_RX FAN_TACHIN
103 LID# SLEEP#
104 VCC_12V VCC_12V
105 VCC_12V VCC_12V
106 VCC_12V VCC_12V
107 VCC_12V VCC_12V
108 VCC_12V VCC_12V
109 VCC_12V VCC_12V
110 GND(FIXED) GND(FIXED)
Table 1: miniBASE-10R AB Pin Definitions
Table of contents
Other ADLINK Technology Carrier Board manuals
