PowerBridge NulPC cPCI-8602 User manual


NuIPC
£
cPCI-8602
6U CompactPCI Single Slot 64-bit/66MHz
Hot Swappable Dual PMC Slot Carrier Board
User’s Guide


Copyright 2004 ADLINK TECHNOLOGY INC.
All Rights Reserved.
Manual Rev. 1.1: May 29, 2004
Part No: 50-15023-101
The information in this document is subject to change without prior notice in
order to improve reliability, design, and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
NuIPC, cPCI-8602 are registered trademarks of ADLINK TECHNOLOGY INC.
Other product names mentioned herein are used for identification purposes
only and may be trademarks and/or registered trademarks of their respective
companies.


Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK TECHNOLOGY INC. If you
need any help or service, please contact us.
ADLINK TECHNOLOGY INC.
Web Site http://www.adlinktech.com
Sales & Service [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan
Please email or FAX your detailed information for prompt, satisfactory, and
consistent service.
Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
Environment
OS:
Computer Brand:
M/B: CPU:
Chipset: BIOS:
Video Card:
NIC:
Other:
Detail Description
Suggestions for ADLINK


Table of Contents
x
i
Table of Contents
Chapter 1 Introduction ....................................................... 1
1.1 Features .................................................................................... 2
1.2 Specifications ............................................................................ 3
Chapter 2 Getting Started .................................................. 5
2.1 What’s Included......................................................................... 5
2.2 Unpacking ................................................................................. 6
2.3 cPCI-8602 Layout...................................................................... 7
2.4 Voltage Selection ...................................................................... 8
2.5 Functional Block Diagram ......................................................... 9
2.6 Pinouts..................................................................................... 10
Chapter 3 Installation ....................................................... 19
3.1 PMC Board Installation............................................................ 19
Warranty Policy ................................................................ 21


How to Use This Guide
x
iii
How to Use This Guide
This manual is designed to assist users in understanding the cPCI-8602 and
describes how to modify settings to meet specific application requirements.
Chapter 1 Introduction
Overview of product features, applications, and specifications.
Chapter 2 Getting Started
Describes unpacking and illustrates connector pin assignments.
Chapter 3 Installation
Describes setup and installation.


Introduction
x
1
1
Introduction
The cPCI-8602 6U CompactPCI single slot 64-bit hot swappable dual PMC
carrier board offers the flexibility required by most I/O applications. The cPCI-
8602 is designed in accordance to PICMG 2.0 R3.0 and PICMG 2.1 R2.0
specifications. Its 6U cPCI design only occupies one system slot and accepts
two single-sized PMC modules or one double-sized PMC module. The 64-
bit/66MHz PCI R2.1-compliant bus ensures efficient cPCI communication
with either 3.3V or 5V PMC modules. Rear I/O PMC modules are also
supported through an optional cPCI rear I/O transition module.
The on-board transparent PCI-to-PCI bridge supplies the additional dual
PMC slots without the hassles of PCI bus mastering. This bridge also
supports a 32-bit/64-bit CompactPCI bus and 33/66MHz PMC cards.
An ELMA handle and hot-swappable functionality guarantee easy installation
and removal. The cPCI-8602 ground is isolated to prevent signal noise from
the chassis.


2
x
Introduction
1.1 Features
x PICMG 2.0 CompactPCI Specification R3.0 Compliant
x PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant (optional)
x 6U cPCI form factor, 1-slot (4TE/HP) width
x Design for one dual-size or two single-size PMC modules
x Optional cPCI rear I/O transition module support for rear I/O PMC
modules
x 64-bit/66MHz PCI bus for both cPCI and PMC slots
x Supports universal (3.3V and 5V) voltage CompactPCI boards and PMC
module (default is 5V)


Introduction
x
3
1.2 Specifications
General CompactPCI Features
x PCI Rev.2.1 compliant
x PICMG 2.0 CompactPCI R3.0 compliant
x PICMG 2.1 CompactPCI Hot-Swap specification R2.0 compliant (optional)
x PICMG 2.3 PMC I/O on CompactPCI specification R1.0 compliant
Form Factor
x Standard 6U CompactPCI (board size: 233.35mm x 160mm)
x Single slot (4TE/HP, 20.32mm)
PCI Bus Bridge
x Intel 21154 transparent PCI to PCI bridge (or equivalent)
x Supports on-board dual PMC slots with PCI bus mastering
x Supports 32-bit/64-bit PCI data/address lines for CompactPCI bus and
PMC slots with 33/66MHz PCI clocking
x Full hot-swap support
PMC Slots
x Supports IEEE P1386.1 standard PMC (PCI Mezzanine Card) module
x Designed for one dual-size or two single-size PMC modules
x All on-board PMC slots are PCI bus mastered
x Supports 32-bit/64-bit PCI data/address lines with 33/66MHz PCI clocking
x Supports 3.3V, 5V, and universal voltage PMC modules (default is 5V)
x Optional PMC1 J14/P14 connects to CompactPCI J3 for rear I/O
(Reserved)
x Optional PMC2 J24/P24 connects to CompactPCI J5 for rear I/O
(Reserved)
Front Panel LEDs
x Power status (green LED)
x Hot-swap status indicator (blue LED)
Other
x Chassis GND is isolated from digital ground on carrier board
x ELMA handle with hot-swap micro-switch
x New Rittal EMC spring prevents EMC spring damage


Getting Started
x
5
2
Getting Started
This chapter describes how to prepare the cPCI-8602 for installation. Please
carefully review the unpacking information before removing the product.
Optional settings are also specified below.
2.1 What’s Included
In addition to this User's Manual, the package includes the following item:
x cPCI-8602 Dual PMC Slot Carrier Board
If anything is missing or damaged, contact the dealer the product was
purchased. Save the shipping materials and carton to ship or store the
product in the future.


6
x
Getting Started
2.2 Unpacking
The cPCI-8602 contains sensitive electronic components that can be easily
damaged by static electricity.
Prepare a grounded anti-static mat. The operator should be wearing an anti-
static wristband, grounded at the same point as the anti-static mat.
Inspect the card module carton for obvious damage. Shipping and handling
may cause damage to the module. Be sure there is no obvious damage due
to shipping and handing by examining the shipping box.
After opening the card module carton, extract the system module and place it
only on a grounded anti-static surface, component side up.
Note: DO NOT APPLY POWER TO THE CARD IF IT HAS BEEN
DAMAGED.


Getting Started
x
7
2.3 cPCI-8602 Layout
Figure 2.1 cPCI-6802 Layout


8
x
Getting Started
2.4 Voltage Selection
The cPCI-8602 supports both 3.3V and 5.0V PMC modules. The factory
default setting is 5V. To change to 3.3V, change the mini-jumper position of
JPY1 from pin2-3 to pin1-2.
JPY1Jumper Setting : The mini-jumper of JPY1 is used to set the
PMC VIO to 3.3V or 5V (Default)
Status JPY1
PMC VIO set to
3.3V
PMC VIO set to
5V (Default)
123
123


Getting Started
x
9
2.5 Functional Block Diagram
Figure 2.2 cPCI-6802 Functional Layout
Note: J3 and J5 are reserved.


10
x
Getting Started
2.6 Pinouts
CompactPCI J3 Pin Assignments (Reserved)
Notes:
1. PMC1IO* signals are connected to the lower PMC Slot (i.e. Slot 1).
2. Pins in J3 columns 15 through 19 are not connected (NC).
3. V(I/O) default is 5V and is controlled by JPY1. However, 3.3 V is
available as a factory option (see Section 2.4).


Getting Started
x
11
CompactPCI J5 Pin Assignments (Reserved)
Notes:
1. PMC2IO* signals are connected to the upper PMC slot (i.e. Slot 2).
2. Pins in J5 columns 14 through 22 are not connected (NC).
3. Pin A1 is active low on some transition modules to indicate the module is
present (TMPRSNT_L).


12
x
Getting Started
PMC slot pin assignments
J11 & J21 32-bit PCI