ADTRAN 1187711G1 User manual

jobAid
1
DESCRIPTION
The Total Access®3XX ONT Mounting Bracket is used to install
an Electronics Module indoors in an unrestricted access location.
It is critical that the Electronics Module remain closed. This Job
Aid provides instruction for installing screws to prevent the
Electronics Module from being opened. This Job Aid also
provides instructions for mounting the ONT Mounting Bracket.
The Total Access 3XX ONT Mounting Bracket, pictured above, is
used to mount any of the ONTs listed in the following table.
ONT Part Number
1st Generation
TA 351 1187701G1
TA 352 1187702G1
TA 361 1187711G1
TA 362 1187712G1
TA 362S 1187712G2
TA 362R 1187715G1
2nd Generation
TA 351 1287701G1
TA 352 1287702G1
TA 361 1287711G1
TA 362 1287712G1
TA 362R 1287715G1
Misc.
TA 354E 1287704G1
TA 352H 1287702G3
TA 362H 1287712G3
TA 3XX
ONT Mounting Bracket
Indoor Unrestricted Access
INSTALLATION
After unpacking the 1187777G1, inspect it for damage. If damage
is noted, file a claim with the carrier and then contact ADTRAN.
For more information, refer to the warranty.
Required Tools and Supplies
Standard technician tools and those listed below are required for
installing the 1187777G1:
•RJ45 Crimper
•Carpenter’s level
•3/32” (0.24 cm) screw driver
•Electric Drill and assorted bits
•5/32” (0.4 cm) hex tamper proof bit
Included with the 1187777G1 packaging is a plastic bag
(P/N 3356046) that contains #6 Pan Head screws (4 ea) used to
mount the ONT Mounting Bracket. The remaining contents of
P/N 3356046 will be used to secure the Electronics Module.
Wall Preparation
The ONT Mounting Bracket is used to mount the Electronics
Module. To prepare the wall to accept the Mounting Bracket, use
the illustration below and complete the following steps:
1. Attach a 3/4 inch (1.9 cm) Mounting Board (typically ply-
wood) to the wall studs using four, 2.5 inch (6.35 cm) (or
greater) wood screws.
2. Use the keyholes on the top of the ONT Mounting Bracket as
location markers and install two #6 Pan Head screws. Leave
approximately 1/16 inch (0.16 cm) protruding from the
mounting surface.
3. Slide the ONT Mounting Bracket over the Pan Head screws
and exert a small amount of downward pressure to ensure
the top of the slots rest on the shafts of the Pan Head screws.
Wood Screws (4 ea)
Pan Head Screws (2 ea)
Mounting Board
Wall
Product P/N: 1187777G1
Issue Date: March 2012
Document P/N: 61187777G1-22A

261187777G1-22A
This module has holes that are pre-drilled completely through the
module.
Before the 1st Generation Electronics Module can be secured, the
partially drilled hole must be completely drilled through the
housing. This is one of two holes that will be used to prevent the
Electronics Module from being opened.
Refer to the illustration below and complete the following
procedure:
1. On the reverse side of the Electronics Module there is a par-
tially drilled hole. Select an appropriate sized bit and com-
plete the hole by carefully drilling through the housing.
2. Remove any plastic shavings.
POTS 2
POTS 1
TELCO ACCESS
ETH 1 ETH 2
ETH 3
ETH 4
TOTAL ACCESS 354E
1287704G1
12V , 1.0A
POWER
NETWORK STATUS
TELEPHONE TROUBLESHOOTING
1. Identify the bad line.
2. Disconnect the plug from the appropriate POTSjack and plug
any working telephone into that jack.
If the telephone works, there is a problem inside the house.
If the telephone does not work, contact your service provider.
3. Remove the telephone and replace the plug into the POTS jack.
4. Close the unit.
CLEI
TEL. NUMBER
Pre-Drilled
Hole
Pre-Drilled
Hole
Partially Drilled Hole
4. Lock the ONT Mounting Bracket in place at the bottom with
the two remaining #6 Pan Head screws.
ELECTRONIC MODULES
There are two different type of Electronic Modules. The 1st
Generation Electronics Module is displayed below.
This module has one pre-drilled hole at the lower left hand side,
and one hole that is not completely drilled through at the top
right hand side.
The following is an illustration of the 2nd Generation electronics
Module.
Keyholes Keyholes
#6 Pan Head
Screw
#6 Pan Head
Screw
FXS 0/1
FXS 0/2
Partially Drilled Hole
on Reverse
RING
TIP
RING
TIP
FXS 0/1
FXS 0/2
ETH 0/1
ETH 0/2
POTS 1
POTS 2
ETH 1
CLEI
TIP RING
TEL. NUMBER
TIP RING
TIP RING
TIP RING
Pre-Drilled
Hole

61187777G1-22A 3
PREVENT THE ELECTRONICS MODULE FROM
BEING OPENED
It is critical that the Electronics Module not be opened. This
procedure prevents the Electronics Module housing from being
opened.
Included with the 1187777G1 packaging is a plastic bag
(P/N 3356046) that contains the following hardware required to
secure the Electronics Module:
•6-32, 1.25 inch (0.47, 3.17 cm) screw (1 ea)
•6-32, 1.5 inch (0.47, 3.81 cm) screw (1 ea)
•6-32 (0.47 cm) hex nuts (2 ea)
Refer to the following illustration and complete the following
steps:
1. Insert the 1.25 inch screw through the hole in the upper right
hand corner and secure with a hex nut. Do not over tighten.
2. Insert the 1.5 inch screw through the hole in the lower left
hand corner and secure with a hex nut. Do not over tighten.
INSTALL THE ELECTRONIC MODULE IN THE
ONT MOUNTING BRACKET
To attach the Electronics Module to the ONT Mounting Bracket,
use the illustrations in the next column and complete the
following steps:
1. Remove the two Mounting Posts from the plastic bag
(P/N 3356046) that accompanied the unit.
2. Install these posts in the post holes in the ONT Mounting
Bracket.
POTS 2
POTS 1
TELCO ACCESS
ETH 1 ETH 2
ETH 3
ETH 4
TOTAL ACCESS 354E
1287704G1
12V , 1.0A
POWER
NETWORK STATUS
TELEPHONE TROUBLESHOOTING
1. Identify the bad line.
2. Disconnect the plug from the appropriate POTSjack and plug
any working telephone into that jack.
If the telephone works,there is a problem inside the house.
If the telephone does not work,contact your service provider.
3. Removethe telephone and replace the plug into the POTS jack.
4. Close the unit.
CLEI
TEL. NUMBER
1.25 “ screw
1.5” screw
3. Match the mounting holes on the Electronics Module with
the connection points on the Mounting Posts and snap
together. The Electronics Module should swing freely.
4. Connect a Ground Wire to the Ground Terminal.
CAUTION
!
This equipment must be connected to a known, reliable earth
ground at all times during installation and service. Refer to the
National Electrical Code (NEC) and state/local codes for details
on grounding requirements. A 12 AWG copper ground conductor
shall be used to connect the equipment to earth ground.
NOTE
Use the Telco Security Screw on the front of the Electronics
Module to secure the Electronics Module to the ONT Mounting
Bracket until such time as wiring to the Electronics Module is
performed.
Mounting Bracket and Post
Mounting Bracket and Post
Ground Wire

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
©2012 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61187777G1-22A*
GENERAL INSTRUCTIONS
TNV connections to this unit should be made using wiring termi-
nating in RJ-type connections only. No bare wiring intended for
connection to TNV screw terminals shall be utilized when this
unit is wall mounted to the indoor wall ONT Mounting Bracket.
CAUTION
!
• Use only UL Listed fiber cables suitable for the application
having no metallic members or other electrically conductive
materials.
• Do Not install the Primary Protector on the ONT Mounting
Bracket.
NOTICE
This completes the Installation portion of the ONT Mounting
Bracket. For all other installation procedures, refer to the Job Aid
and Installation Guide provided with the ONT being used.
SPECIFICATIONS
Specifications for the 1187777G1 are as follows:
•Physical
oHeight: 12.0 inches (30.48 cm)
oWidth: 8.0 inches (20.32 cm)
oDepth: 2.75 inches (with Electronics Module installed) (6.98
cm)
oWeight: 14 ounces (0.444 kg)
•Environmental
oOperational Temperature Range: –40°C to +65°C
oStorage Temperature Range: –40°Cto+85°C
oRelative Humidity: up to 95%, noncondensing
SAFETY AND REGULATORY COMPLIANCE
Refer to the Safety and Regulatory Compliance Notice for this
product (P/N 61187777G1-17) for detailed safety and regulatory
information.
Consultez l'avis sur la sécurité et la conformité à la réglemen-
tation pour ce produit (61187777G1-17) pour obtenir des
renseignements détaillés sur la sécurité et la réglementation.
Ausführliche Sicherheits- und regulatorische Informationen sind
in der Konformitätserklärung zur Sicherheit und Einhaltung von
Normen zu diesem Produkt (61187777G1-17) aufgeführt.