Advantech ASMB-922I Installation and operation manual

ASMB-922I Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 ASMB-922I Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
ASMB-922I Intel® Xeon® E5-2600 series Dual 2011 Socket
EATX Server Board with 4 PCIe Expansion Slots
Startup Manual
Standard SBC Functions
• CPU: LGA2011 Intel ® Xeon® E5-2600 series
• BIOS: AMI 64 Mb SPI BIOS
• Chipset: Intel® C602J PCH
• System Memory: 8* DDR3 REG/ECC/Non-ECC
1066/1333/1600 unbuffered DIMM, Max. 128 GB
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 128 GB RAM
when 128 GB RAM is installed.
• SATA Interface: 4 x SATA2 3 Gb/s ports, 2 x SATA3
6Gb/s, supports Intel Matrix Storage (for Windows only)
software RAID 0, 1, 10 & 5.
• Serial ports: Two serial ports, only support RS-232
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse
• Watchdog timer: 255 level timer intervals
• USB port: Supports up to eleven USB 2.0 ports (1*Type-
A) and two USB 3.0 ports
VGA Interface
• Chipset: Aspeed AST2300
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:Intel 82579LM; LAN2: Intel I210; LAN3:
Realtek 8201EL(10/100Mbps for IPMI, ASMB- 922I sku
only)
Mechanical and Enviroment
• Dimensions (L x W): 330 x 304 mm (13” x 12”)
•Power supply voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
•Power consumption (mainboard only, excluding IO
device): Max. load: +3.3 V @ 19.69 A, +5 V@ 7.77 A, +12
V @ 14.66 A, +12 V(8P1) @ 22 A, +12 V(8P2) @ 22 A,
+5 Vsb@ 2 A
•Operating temperature: 0 ~ 40° C (depending on CPU)
•Weight: 1.7 kg (weight of board)
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the ASMB-922I series Rev. A1
Part No. 2006922I10
Print in China
1st Edition
May 2013

2 ASMB-922I Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application.
The table below lists the function of each of the jumpers and
connectors.
Connectors
Label Function
ATXPWR1 ATX 24 Pin main power connector
ATX12V1 Processor power connector
(for CPU0)
ATX12V2 Processor power connector(for
CPU1)
SATA0~SATA5 Serial ATA0~5
USB2_3, USB4_5,
USB6_7, USB8_9
USB 2.0 header 2, 3, 4, 5, 6,
7, 8, 9
USB0_1, USB30_1,
USB10
USB 2.0 port 0, 1; USB 3.0 port
0, 1; USB 2.0 port 10 (Type-A)
PCIE_PME1 PCIE x16 slot (For PME)
PCIEX8_SLOT4,
PCIEX16_SLOT5,
PCIEX16_SLOT6,
PCIEX16_SLOT7
PCIE x8 & x16 slot
DIMMA1 ~ DIMMH1 DDR3 slot
CPUFAN0,CPUFAN1 CPU FAN connector
SYSFAN0,SYSFAN1,
SYSFAN2 System FAN connector
LAN1,LAN2 LAN connector
BMC LAN1 LAN connector for IPMI
VGA_COM1 VGA+COM connector
KBMS1 Keyboard and mouse connector
KBMS2 External keyboard and mouse
connector (6 pin)
BIOS_SKT1 BIOS SPI ROM
LANLED1 LAN LED extension connector
SMBUS1 Front panel SMBus header
BMC1 IPMI module header
SATA_SGPIO_1 SATA SGPIO header
JCASE1 Chassis case open alarm
header
AUDIO1 Audio header
COM2 Serial port: RS-232
JFP1, JFP2, JFP3 Front panel header
GPIO GPIO connector
Jumper list
Label Function
JCMOS1 CMOS clear
JME1 ME update
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
JFP1, JFP2
Pin.3 #PWR_SW
Pin.6 GND
Pin.9 #RST_SW
Pin.12 GND
*Power button pin is located in Pin 3 & 6 of front panel
connector
Jumpers and Connectors
Jumpers and Connectors
1 2 3
Installation Note
3 6 9 12 PWRSW RESET
HDDLED
SNMP
JFP1
&
1(+) 4 7 10(-)
HDDLED
SM_BUS
SPEAKER
JPF2
&
PWRLED & KEYLOCK
12345JFP3
2(+) 5(-) 8 11
1 2 3

ASMB-922I Startup Manual 3
The device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
The CD disc contains a driver installer program that will lead
you through the installation of various device drivers needed
to take full advantage of your motherboard.
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used bat-
teries according to manufacturer’s instructions.
Software Installation Declaration of Conformity
Board Layout
Figure 1: Board Layout: Jumper and Connector Locations

4 ASMB-922I Startup Manual
1. Take off all the plastic caps behind the mounting holes
2. Insert the PME module into the PME slot of ASMB-922I
3. Take the plastic holder out from the bag.
Procedure for assembling the PME module to ASMB-922I motherboard
4. Find the two PME mounting holes.
5. Push the plastic holders down and make the latch pass
through and into those two holes.
6. Check and make sure that the plastic holder is firmly
connected to the two PCBs.
Notes
Hold ASMB-922I this way to prevent damage. Do NOT hold ASMB-922I this way, it may cause chip dam-
age.

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Advantech:
ASMB-922I-00A2E