Advantek Networks AWN-AP-54MR User manual

802.11b+g Access Point
User Manual
Model: AWN-AP-54M

FCC Certifications
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC ules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
 eorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC F adiation Exposure Statement
This equipment complies with FCC F radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your
body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures.
All trademarks and brand names are the property of their respective
proprietors.
Specifications are subject to change without prior notification.

Table of Content
Introduction 1
FEATU ES ....................................................................................................1
APPLICATION ................................................................................................2
PA TS NAMES AND FUNCTIONS .....................................................................3
FACTO Y DEFAULT SETTINGS .......................................................................5
Wireless AP ............................................................................................5
Hardware Connection 6
Check the LEDs: .......................................................................................6
About the Operation Modes 7
ACCESS POINT MODE....................................................................................7
WDS EPEATE MODE ................................................................................7
CLIENT MODE (INF AST UCTU E) .................................................................7
CLIENT MODE (AD-HOC) ................................................................................8
WDS BIDGE MODE .....................................................................................8
Configuration 9
LOGIN ..........................................................................................................9
STATUS ......................................................................................................10
System ..................................................................................................10
Statistics................................................................................................11
WI ELESS ..................................................................................................13
Basic Settings .......................................................................................13
Advanced Settings ................................................................................15
Security .................................................................................................19
Access Control......................................................................................21
TCP/IP ......................................................................................................24
Basic .....................................................................................................24
OTHE .......................................................................................................27
Upgrade Firmware ................................................................................27
Save/ eload Settings ...........................................................................28
Password ..............................................................................................30
System Log ...........................................................................................30

1
INT ODUCTION
This is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless
Access Point. The Wireless Access Point is equipped with two 10/100 M Auto-
sensing Ethernet ports for connecting to LAN and also for cascading to next
Wireless Access Point.
This Access Point provides 64/128bit WEP encryption, WPA and IEEE802.1x
which ensures a high level of security to protects users’ data and privacy. The
MAC Address filter prevents the unauthorized MAC Addresses from accessing
your Wireless LAN. Your network security is therefore double assured.
The web-based management utility is provided for easy configuration that your
wireless network connection is ensured to be always solid and hassle free.
Features
• Two LAN ports for Wireless AP cascade.
• Support WPA.
• Support AP client mode.
• Support WDS for bridge mode.
• Support data rate automatic fallback.
• Automatic channel selection.
• Client access control.
• Support 802.1x/ adius client with EAP-TLS, TKIP, AES encryption.
• Support IAPP.
• Adjustable Tx power, Tx rate, and SSID broadcast.
• Allow WEP 64/128 bit.
• Web interface management.
• Support System event log and statistics.
• MAC filtering (For wireless only).

2
Application
Example 1
Example 2

3
Parts Names and Functions
1. Front Panel: (LED Indicators)
LED Status
Indicator Color Solid Flashing
1 Power Green Turns solid green when
power is applied to this
device.
N/A.
2 Status ed Turns solid red when
the device is booting,
after boot scuessfully,
the light turn off.
Link/Act. Green Turns solid green when
connected and
associated to at least a
client station.
eceiving/
Sending data
WEP/WP
A
Orange
Turns solid orange
when wireless security
is enabled.
N/A
3~6
Wireless
MAC Ctrl
Orange
Turns solid orange
when MAC Control is
enabled.
N/A

4
WDS
Orange
Turn solid orange
when WDS is enabled.
N/A
7 LAN 1
8 LAN 2
Green Turns solid green when
linked to a local
network.
eceiving/
Sending data
Table 1: LED Indicators
2. ear Panel: Connection Ports
Port/button Functions
A 12V DC Connects the power adapter plug
B LAN1 Connects to Ethernet
C LAN2 Connects to Ethernet
D (Factory)
ESET
Press over 3 seconds to reboot this device.
Press for over 10 seconds to restore factory
settings.
Performing
the Factory eset will erase all
previously entered device settings.
Table 2: Connection Ports

5
Factory Default Settings
Setting Wireless Access Point
Device Name Wireless AP
SSID Default value: 802.11g-AP
Channel 11
WEP Default value: Disabled
IP Address 192.168.1. 254


6
HA DWA E CONNECTION
Note: Before you starting hardware connection, you are advised to find an
appropriate location to place the Access Point. Usually, the best place for the
Access Point is at the center of your wireless network, with line of straight to all
your wireless stations. Also, remember to adjust the antenna; usually the
higher the antenna is placed, the better will be the performance.
1. Connect to your local area network: connect a Ethernet cable to one of
the Ethernet port (LAN1 or LAN2) of this Wireless Access Point, and the
other end to a hub, switch, router, or another wireless access point.
2. Power on the device: connect the included AC power adapter to the
Wireless Access Point’s power port and the other end to a wall outlet.
Check the LEDs:
The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is
traffic.
The Link/Act LED will be on in static when associated with a station and blink
whenever this AP receives data packets in the air.
If the Status LED glows after self-test , it means this Wireless Access Point
fails on self test. Please ask your dealer for technical support.
3. Configure your PC: Make sure your local PC(s) has wireless network
adapter installed.

7
About the Operation Modes
This device provides four operational applications with Access Point, Bridge,
Client (Ad-hoc) and Client (Infrastructure) modes, which are mutually
exclusive.
This device is shipped with configuration that is functional right out of the box. If
you want to change the settings in order to perform more advanced
configuration or even change the mode of operation, you can use the web-
based utility provided by the manufacturer as described in the following
sections.
Access Point Mode
When acting as an access point, this device connects all the stations
(PC/notebook with wireless network adapter) to a wired network. All stations
can have the Internet access if only the Access Point has the Internet
connection.
See the sample application below.
To set the operation mode to Access Point, please go to “Wireless 

Basic
Settings”, in the “Mode” field click the down arrow  to select AP mode.
WDS epeater Mode
efer to the illustration below. While acting as Bridges, AP1 (with Station 1
being associated to) and AP2 (with Station 2 being associated) can
communicate with each other through wireless interface (with WDS). Thus
Station 1 can communicate with Station 2 and both Station 1 and Station 2 are
able to access the Internet if only AP1 or AP2 has the Internet connection.
To set the operation mode to Bridge, please go to “Wireless 

Basic
Settings”, in the “Mode” field click the down arrow  to select AP mode. And
go to “Wireless 

WDS Settings” to enable WDS.
Client Mode (Infrastructure)
If set to Client (Infrastructure) mode, this device can work like a wireless station
when it’s connected to a computer so that the computer can send packets from
wired end to wireless interface.