adyen NYC1 User manual

Adyen NYC1 and NYC1-SCR
User Manual

NYC1/NYC1-SCR USER MANUAL
2
THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL
OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM Adyen NV.
Address: Simon Carmiggeltstraat 6-50, Amsterdam, 1011 DJ, Netherlands
Phone: [phone]

NYC1/NYC1-SCR USER MANUAL
3
REVISION HISTORY
Version
Data
Change description
1.0.0
13.06.2022
Release version
1.1.0
02.08.2022
Updated section “SERVICE AND SUPPORT”
1.2.0
23.09.2022
Updated section “REGULATORY”
1.3.0
14.10.2022
Added NYC1
1.4.0
16.11.2022
Updated section “TECHNICAL SPECIFICATIONS”
1.5.0
17.11.2022
Updated section “REGULATORY”

NYC1/NYC1-SCR USER MANUAL
4
CONTENTS
REGULATORY........................................................................................................................................................................... 5
TECHNICAL SPECIFICATIONS ................................................................................................................................................... 6
GENERAL VIEW........................................................................................................................................................................ 7
GETTING STARTED................................................................................................................................................................... 8
PERIODIC INSPECTION AND MAINTENANCE .......................................................................................................................... 9
OPERATION MODES .............................................................................................................................................................. 10
APPLICATION/FIRMWARE DOWNLOAD MODE,SYSTEM MODE AND CLEARING BLUETOOTH PARING INFO ................................................. 10
STATUS LEDS........................................................................................................................................................................ 10
BLUETOOTH PAIRING.............................................................................................................................................................. 12
UPDATE FIRMWARE AND APPLICATION WITH USING FIRMWARE API................................................................................................ 13
MAGNETIC CARDS READING ..................................................................................................................................................... 14
CONTACTLESS CARDS READING.................................................................................................................................................. 15
SMART CARDS READING........................................................................................................................................................... 16
CARE, MAINTENANCE AND WARRANTY............................................................................................................................... 17
SERVICE AND SUPPORT......................................................................................................................................................... 17

NYC1/NYC1-SCR USER MANUAL
5
REGULATORY
FCC Statement
FCC ID: 2A7UQ-NYC1
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.

NYC1/NYC1-SCR USER MANUAL
6
TECHNICAL SPECIFICATIONS
Processor
ARM Cortex® M4 Security Microcontroller
Memory
32KB I&D-Cache
1MB Internal RAM
8КB OTP
Application Memory
8MB Serial Flash
Keypad
• ON / OFF key
Magnetic Card Reader
(For MSR version)
• 3-track bi-directional reading
• ISO 7810, 7811 and 7813
Smart Card Reader
ISO7816, EMV L1 certified
Contactless Card Reader
for payment applications
(option)
• AMEX ExpressPay
• Discover D-PAS
• MasterCard Contactless
• VISA PayWave
• China Union Pay
• JCB
Contactless Card Reader
•NFC-A/ISO 14443 Type-A
•NFC-B/ISO 14443 Type-B
•NFC-F/Felica
•NFC-V/ISO 15693
Battery
Rechargeable lithium-ion polymer battery 3.8V, 500mAh
Connectivity
• USB (from USB type C port or rear pads)
- Device
• BLE 5.1
• UART pass through rear pads
Audio indication
Speaker (power 0.5W)
OS compatibility
iOS, Android, Windows
Reliability
• 500 000 chip card cycles
Certifications
CE Mark, UCKA Mark, FCC, EMV Level 1, EMV Level 2, EMV Level 1 Contactless, PCI PTS 6.1
Dimensions (LxWxH), mm
94 x 70 x 13
Weight, g
95
Environmental
Operating: -10oC to +45oC / 5 to 90% RH
Storage: -20oC to +70oC / 5 to 90% RH
Power Supply
• 5V through USB C
• 5V through rear pads
Accessories
• Docking station
* Specification can be change without any notice.
Use only original equipped cable USB-A to USB-C.
Use only approved USB adapters. The minimum requirements of USB adapter
are 5V/500mA.
Waste Electrical & Electronic Equipment
The symbol means that according to local laws and regulations your product
shall be disposed of separately from household waste at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material
resources.

NYC1/NYC1-SCR USER MANUAL
7
GENERAL VIEW
Figure 1
1. LEDs indication for Contactless transaction / LEDs indication for device status
2. On/Off button (Bluetooth pairing and cancel button)
3. Rear Pads (USB and charging)
4. Opening for inserting smart card
5. Speaker
6. Contactless reader
7. USB port
8. Opening for magnetic card

NYC1/NYC1-SCR USER MANUAL
8
GETTING STARTED
NYC1/NYC1-SCR has rechargeable Li-Po battery. Can be charge from USB port or Rear pads.
Before first use, battery must be fully charged.
If the device is fully discharged, charging time to fully charged would be approx.
1 hour and 30min.
Charging form USB adapter:
Figure 2
Main battery replacement:
To replace the main battery of NYC1/NYC1-SCR please contact with your local
Adyen representative or service provider.

NYC1/NYC1-SCR USER MANUAL
9
PERIODIC INSPECTION AND MAINTENANCE
The following inspections must be performed on a regular basis after initial receipt and installation of
NYC1/NYC1-SCR:
• There are no visual indications for trying unauthorized opening of the device
• There are no unusual wires connected to the ICC acceptor or any of the ports on the terminal.
• There is no shim device in the ICC acceptor slot.
• The terminal serial number (on the label) corresponds to the one in the inventory paperwork.

NYC1/NYC1-SCR USER MANUAL
10
OPERATION MODES
For start operating with NYC1/NYC1-SCR needs to be paired to another Bluetooth BLE device with
installed application. For downloading the latest SDKs for iOS, Android and Windows please contact
with your distributor.
Application/Firmware download mode, System mode and Clearing Bluetooth
paring info
Application download mode - to enter in “FW/AP download mode” on the NYC1/NYC1-SCR, the power
button must be maintained pressed and USB cable plugged. A characteristic sound is played and first
white LED will start to light. Power button must be hold until second white LED is light on, then is
releasing the power button. When device is in Boot Loader/Application download mode will be played
characteristic sound.
System mode - to enter in “SYSTEM MODE” on the NYC1/NYC1-SCR, the power button must be
maintained pressed and USB cable plugged. A characteristic sound is played and first white LED will
start to light. Power button must be hold until third white LED is light on, then is releasing the power
button.
Clear Bluetooth pairing information - to enter in “Clear Bluetooth Pairing Info” on the NYC1/NYC1-
SCR, the power button must be maintained pressed. A characteristic sound is played, and forth white
LED will start to light, then is releasing the power button. When pairing info is cleared will be played
characteristic sound.
Status LEDs
LED indication
Green LED continuously light on
Green LED flashing

NYC1/NYC1-SCR USER MANUAL
11
LED indication
Description
Device operating
No indication
Device is turned off
No indication (Depends
of Application)
Device is turned on
Second white LED lights
up constantly
Please refer to “Application download
mode”
Third white LED lights
up constantly
Please refer to “System mode”
Forth white LED lights
up constantly
Please refer to “Clear Bluetooth pairing
information”
System errors
After power on the
device, on front side
first LED light
continually and fourth
LED blinking
Device is TAMPERED
Second LED light
continually and fourth
LED blinking
Device error (General Exception)

NYC1/NYC1-SCR USER MANUAL
12
Bluetooth Pairing
Turn on NYC1/NYC1-SCR, attached it to PC via USB cable. When device is connected to PC, will create
virtual COM port. Check on device manager on which port is connected. After that run the special
application for PC (Fig. 3). Press “Search” button on the app, and in right side will be show all available
COM ports. Select on which is connected device, then press “Connect to device”. From Bluetooth
management on mobile device (equipped with BLE 4.2) select connect to NYC1/NYC1-SCR, then on
mobile device screen will be show PASSKEY (Fig. 6). White LEDs will start to light one by one continually,
on special app will be show Passkey (Fig. 4), if they are same press “On/Off” two times on NYC1/NYC1-
SCR to confirm (Fig. 5), then special app return message “THE DEVICES ARE CONNECTED” (Fig.7 when
on each device is confirming pairing). If Passkey is being different press “On/Off” button one time on
NYC1/NYC1-SCR to cancel pairing.
Figure 3
Figure 4
Figure 5
Figure 6

NYC1/NYC1-SCR USER MANUAL
13
Figure 7
Update Firmware and Application with using Firmware API
Loaded Firmware and Application on NYC1/NYC1-SCR can be updated via Application which is using
Firmware API. After pairing NYC1/NYC1-SCR to COTS device via Bluetooth, as described on “Bluetooth
Pairing”. Run the Application* on COTS (smart device) and press “Update device firmware”.
Figure 8
* In order to use the NYC1/NYC1-SCR functions with COTS (smart device), special software must be
used. Please contact your distributor in order to get the latest demo application and SDK.

NYC1/NYC1-SCR USER MANUAL
14
Magnetic cards reading
The NYC1/NYC1-SCR has a built-in magnetic card reader. The card reader incorporates a (3) track
magnetic read head, requiring a single swipe to read field data from all three tracks.
The magnetic reading head faces down. When swiping the card into the reader, the magnetic stripe
must be facing up as shown in the figure below. Keep the edge of the card flat on the inner base of
the reader to ensure that the magnetic stripe passes over the reading head evenly.
Figure 9

NYC1/NYC1-SCR USER MANUAL
15
Contactless cards reading
The contactless card transaction procedure can vary depending on the application loaded on the
NYC1/NYC1-SCR. Verify the proper procedure with your application provider before performing a
contactless card transaction.
In order to use the Contactless card reading function, special software must be used. Please contact
your distributor in order to get the latest demo application and SDK.
To Conduct a Contactless Credit/Debit Card Transaction
1 Place a contactless card to shown on the NYC1/NYC1-SCR contactless logo.
2Remove the card when indicates the transaction is completed.
Figure 10

NYC1/NYC1-SCR USER MANUAL
16
Smart cards reading
The smart card transaction procedure can vary depending on the application loaded on the
NYC1/NYC1-SCR. Verify the proper procedure with your application provider before performing a
smart card transaction.
To Conduct a Smart Card Transaction
1 Position a smart card with the gold contacts facing upward.
2 Insert it into the ICC card reader slot in a smooth, continuous motion until it seats firmly.
3 Remove the card when indicates the transaction is completed.
Figure 11

NYC1/NYC1-SCR USER MANUAL
17
CARE, MAINTENANCE AND WARRANTY
•Keep the NYC1/NYC1-SCR side of the reach of small children.
•Keep the NYC1/NYC1-SCR dry. Precipitation, humidity and liquid
contain minerals that will corrode electronic circuits.
•Do not use or store in dusty or dirty areas.
•Do not drop or knock NYC1/NYC1-SCR.
•Do not open the NYC1/NYC1-SCR. Only qualified personnel can open the
device and make repair. If the NYC1/NYC1-SCR is not working, please
contact with your dealer.
•Forbidden is allowing unqualified personnel to service your NYC1/NYC1-
SCR!
SERVICE AND SUPPORT
Service and Support:
For NYC1/NYC1-SCR problems, product service, and repair information, contact your local Adyen
representative or service provider.
• International – Contact your local Adyen distributor
Service Returns:
All customers, please contact your local Adyen NV representative or distributor for assistance with
your service, return, or replacement.