Aegis 4KEXTENDER-35 User manual

4KEXTENDER-35
4K UHD HDMI EXTENDER
All Rights Reserved Version :4KEXTENDER-35_2019V.1.6
User Manual

4KEXTENDER-35
GENERAL SAFETY INSTRUCTIONS
When using electronic products, please review the following safety precautions before installing or using
the products.
i. Read these instructions.
ii. Keep these instructions.
iii. Follow all instructions.
iv. Heed all warnings.
v. Be sure all cables and equipment are connected to the unit as described in the manual.
vi. Do not use this product near water.
vii. Do not place the product on top of any easily combustible materials such as carpet or fabric.
viii. Do not stacking the product on top of a hot component such as a power amplifier.
ix. Do not use liquid or aerosol cleaners to clean the product. Clean only with a dry cloth and always unplug
the power to the device before cleaning.
x. Do not block any ventilation openings. Blocking the airflow could cause damage. Arrange components so
that air ca flow freely. Ensure that there is adequate ventilation if the product is placed in a stand or
cabinet. Install or place the product in a properly ventilated area, away from direct sunlight or any
source of heat such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
xi. Power cord must be accessible to allow for the removal of the power from the product.
xii. Only use attachments/accessories specified by the manufacturer.
xiii. To reduce the risk of electric shock and/or damage to this product, never handle or touch this unit or
power cord if your hands are wet or damp.
xiv. To avoid electric shock, never stick anything in the slots on the case or remove the cover.
Be careful with electricity:
Power outlet: To prevent electric shock, be sure the electrical plug used on the product
power cord matches the electrical outlet used to supply power to the HPC product. Use
only the power adapter and power connection cables designed for this unit.
Power Adaptor: Be sure the power adaptor is 5V/2A, please matching the rating of
the power voltage.
Lightning: For protection from lightning or when the product is left unattended for
a long period, disconnect it from the power source.
ESD: Handle the product with proper ESD care. Failure to do so can result in failure.
Trademarks All trademarks in this document are the properties of their respective owners.

4KEXTENDER-35
Table of Content
GENERAL SAFETY INSTRUCTIONS...........................................................................................2
INTRODUCTION......................................................................................................................4
PACKAGE CONTENTS ..........................................................................................................4
SYSTEM REQUIREMENTS ....................................................................................................4
CONNECTION DIAGRAM ........................................................................................................5
DEVICE FUNCTION .................................................................................................................6
Transmitter Panel ...............................................................................................................6
Receiver Panel ....................................................................................................................7
IR Pin Assignment ...............................................................................................................8
TECHNICAL SPECIFICATION ....................................................................................................9
Transmitter Specification....................................................................................................9
Receiver Specification.......................................................................................................10
Resolution Specifications ..................................................................................................11
Cable Specifications ..........................................................................................................11
ACRONYMS ..........................................................................................................................12
WARRANTY ..........................................................................................................................13

4KEXTENDER-35
INTRODUCTION
4KEXTENDER-35 with us allows one HDMI, Bi-direction IR to be connected up to 35meters via
single CAT.6 cable for Computer, Laptop, BD Player, Game Console and others HDMI source
devices. Supporting 4Kx2K/60Hz UHD resolution with 8 bit deep color and lossless
compressed audio that make 4KEXTENDER-35 a smart choice for home entertainment,
company conference, commercial advertising and other applications.
PACKAGE CONTENTS
4KEXTENDER-35 Transmitter X 1 PCS
4KEXTENDER-35 Receiver X 1 PCS
5VDC / 2.0 Amp Locking Power adapter X 2 PCS (US, UK, EU Power plug.)
IR Blaster Cable X 1 PCS
IR Receiver Cable X 1 PCS
User Manual X 1 PCS
SYSTEM REQUIREMENTS
HDMI Source device includes SetTop Box, BD Player, Computer, Laptop, Game
Console, Media Player and Camcorder.
HDMI Sink device includes LED/LCD Monitor, LED/LCD TVs, Projector and AV
Receiver.
HDMI 2.0 Premium Certified Cable-Highly recommended
Standard 24AWG Cat.6, Cat.6e or Cat.7 Cable-Highly recommended

4KEXTENDER-35
CONNECTION DIAGRAM

4KEXTENDER-35
DEVICE FUNCTION
Transmitter Panel
1. HDMI IN: Connect to HDMI sources, such as SetTop Box, BD Player, Computer,
Laptop, Game Console, Media Player and Camcorder.
2. IR TX: Transmitting IR signal to remote control HDMI source devices vua IR
Blaster cable.
3. IR RX: Receiving IR signal to remote control HDMI sink devices via IR receiver
cable.
4. DC IN: 5VDC/2.0 Amp Locking Power Jack.
5. POWER LED: This LED will illuminate when power adapter plug in
4KEXTENDER-100 Transmitter.
6. LINK LED: This LED will illuminate when Transmitter connect compatible
Receiver and all signal start to transmission.
7. RJ45: Connect to 4KEXTENDER-35 Receiver with single Cat.6 cable for HDMI,
IR Blaster and IR Receiver signal transmission.

4KEXTENDER-35
Receiver Panel
1. HDMI OUT: Connect to HDMI sink devices, such as LED/LCD Monitor, LED/LCD
TVs, Projector and AV Receiver.
2. IR TX: Transmitting IR signal to remote control HDMI sink devices via IR
Blaster Cable.
3. IR RX: Receiving IR signal to remote control HDMI source devices via IR
Receiver Cable.
4. DC IN: 5VDC / 2.0 Amp Locking Power Jack.
5. POWER LED: This LED will illuminate when power adapter plug in
4KEXTENDER-35 Receiver.
6. LINK LED: This LED will illuminate when Receiver connect compatible
Transmitter and all signal start to transmission.
7. RJ45: Connect to 4KEXTENDER-100 Transmitter with single Cat.6 cable for
HDMI, IR Blaster and IR Receiver signal transmission.

4KEXTENDER-35
IR Pin Assignment
IR Receiver
IR Blaster

4KEXTENDER-35
TECHNICAL SPECIFICATION
Transmitter Specification
HDMI Bandwidth
225MHz / 6.75Gbps
HDMI Resolution
480P,720P,1080P/24,30,50,60Hz, 4Kx2K/50,60Hz.
Audio Format
PCM 2 Channel at 48KHz
HDCP
2.2
Input Port
HDMI X 1
Output Port
RJ45 X 1 - Cat.6/6e/7
Control Port
IR Blaster X 1 - 3.5mm
IR Receiver X 1 - 3.5mm
IR Frequency
20-60Khz
Power Supply
5VDC / 2.0 Amp (US,UK,EU Power Plug)
Power Consumption
10 W - Max.
Chassis Material
Metal
Chassis Color
Black
Operating Temperature
0℃-40℃/ 32℉-104℉
Storage Temperature
-15℃-55℃/ 5℉-131℉
Humidity
5 - 85% RH (Non-Condensing)
Dimension LXWXH
4.33 in (110 mm) X 2.17 in (55 mm) X 0.94 in (24 mm)
Weight
270 g

4KEXTENDER-35
Receiver Specification
HDMI Bandwidth
225MHz / 6.75Gbps
HDMI Resolution
480P,720P,1080P/24,30,50,60Hz, 4Kx2K/50,60Hz.
Audio Format
PCM 2 Channel at 48KHz
HDCP
2.2
Input Port
RJ45 X 1 - Cat.6/6e/7
Output Port
HDMI X 1
Control Port
IR Blaster X 1 - 3.5mm
IR Receiver X 1 - 3.5mm
IR Frequency
20-60Khz
Power Supply
5VDC / 2.0 Amp (US,UK,EU Power Plug)
Power Consumption
10 W - Max.
Chassis Material
Metal
Chassis Color
Black
Operating Temperature
0℃-40℃/ 32℉-104℉
Storage Temperature
-15℃-55℃/ 5℉-131℉
Humidity
5 - 85% RH (Non-Condensing)
Dimension LXWXH
4.33 in (110 mm) X 2.17 in (55 mm) X 0.94 in (24 mm)
Weight
270 g

4KEXTENDER-35
Resolution Specifications
Supported Resolutions (Hz)
HDMI Output
720x480i@60
v
720x480p@60
v
720x576i@50
v
720x576p@50
v
800x600p@56 60 72 75 85
v
1024x768@60 70 75 85
v
1280x720p@50 60
v
1280x768p@60RB/60 75 85
v
1280x800p@60RB/60 75 85
v
1280x960@60 85
v
1280x1024@60 75 85
v
1360x768@60
v
1366x768p@60RB 60
v
1440x900p@60RB 60 75
v
1600x1200p@60
v
1680x1050p@60RB 60
v
1920x1080i@50 60
v
1920x1080p@24 25 30
v
1920x1080p@50 60
v
1920x1200p@60RB
v
2560x1440p@60RB
v
2560x1600p@60RB
v
2048x1080p@50 60
v
3840x2160p@50 60 ( 4:2:0 )
v
3840x2160p@50 60 ( 4:2:0 )
v
3840x2160p@50 60
v
Cable Specifications
Cable Length
1080p/60Hz
4K/30Hz
4K/60Hz
8 bit
8 bit 4:4:4
8 bit 4:4:4
HDMI High Speed Cable
2m
2m
2m
Cat.6/6e/7
60m
50m
35m

4KEXTENDER-35
ACRONYMS
ACRONYM
DESCRIPTION
AV
Audio/Video
Cat.6
Category 6 Cable
Cat.6e
Category 6 Enhance Cable
Cat.7
Category 7 Cable
EDID
Extended Display Identification Data
HDMI
High Definition Multimedia Interface Cable
HDCP
High Bandwidth Digital Content Protection
IR
Infrared
LCD
Liquid-Crystal Display
LED
Light-Emitting Diode
RJ45
Local Area Network
UHD
Ultra High Definition

4KEXTENDER-35
WARRANTY
Limited 3 Year Warranty
aegis Multimedia INC. (“Manufacturer”) warrants that this product is free of defects in both materials and
workmanship for a period of 3 years as defined herein for parts and labor from date of purchase. This Limited
Warranty covers products purchased in the year 2019 and after. During the warranty period, and upon proof
of purchase, the product will be repaired or replaced (with same or similar model) at our option without
charge for parts or labor for the specified product lifetime warranty period.
This warranty shall not apply if any of the following:
A. The product has been damaged by negligence, accident, lightning, water, or mishandling.
B. The product has not been operated in accordance with procedures specified in operating instructions.,
C. The product has been repaired and or altered by other than the manufacturer or authorized service
center.
D. The product's original serial number has been modified or removed.
E. External equipment other than supplied by the manufacturer, in the determination of a manufacturer,
shall have affected the performance, safety or reliability of the product.
F. Part(s) are no longer available for the product.
If the product needs repair or replacement during the specified warranty period, the product should be
shipped back to Manufacturer at Purchaser's expense. Repaired or replaced product shall be returned to
Purchaser by standard shipping methods at Manufacturer's discretion. Express shipping will be at the
expense of the Purchaser.
No other warranty, express or implied other than Manufacturers shall apply.
The manufacturer does not assume any responsibility for consequential damages, expenses or loss of
revenue or property, inconvenience or interruption in operation experienced by the customer due to a
malfunction of the purchased equipment. No warranty service performed on any product shall extend the
applicable warranty period. This warranty does not cover damage to the equipment during shipping and
Manufacturer assumes no responsibility for such damage. This product warranty extends to the original
purchaser only and will be null and avoid upon any assignment or transfer.