Aegis EXP-HDBASET-101 User manual

EXP-HDBASET-101
HDMI Extender HDBaseT
All Rights Reserved Version: EXP-HDBASET-101_2022
User Manual

EXP-HDBASET-101
GENERAL SAFETY INSTRUCTIONS
When using electronic products, please review the following safety precautions before installing or using
the products.
i. Read these instructions.
ii. Keep these instructions.
iii. Follow all instructions.
iv. Heed all warnings.
v. Be sure all cables and equipment are connected to the unit as described in the manual.
vi. Do not use this product near water.
vii. Do not place the product on top of any easily combustible materials such as carpet or fabric.
viii. Do not stacking the product on top of a hot component such as a power amplifier.
ix. Do not use liquid or aerosol cleaners to clean the product. Clean only with a dry cloth and always unplug
the power to the device before cleaning.
x. Do not block any ventilation openings. Blocking the airflow could cause damage. Arrange components so
that air ca flow freely. Ensure that there is adequate ventilation if the product is placed in a stand or
cabinet. Install or place the product in a properly ventilated area, away from direct sunlight or any
source of heat such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
xi. Power cord must be accessible to allow for the removal of the power from the product.
xii. Only use attachments/accessories specified by the manufacturer.
xiii. To reduce the risk of electric shock and/or damage to this product, never handle or touch this unit or
power cord if your hands are wet or damp.
xiv. To avoid electric shock, never stick anything in the slots on the case or remove the cover.
Be careful with electricity:
 Power outlet: To prevent electric shock, be sure the electrical plug used on the product
power cord matches the electrical outlet used to supply power to the HPC product. Use
only the power adapter and power connection cables designed for this unit.
 Power Adaptor: Be sure the power adaptor is 48V/0.5A, please matching the rating
of the power voltage.
 Lightning: For protection from lightning or when the product is left unattended for
a long period, disconnect it from the power source.
 ESD: Handle the product with proper ESD care. Failure to do so can result in failure.
Trademarks All trademarks in this document are the properties of their respective owners.

EXP-HDBASET-101
Table of Content
GENERAL SAFETY INSTRUCTIONS ........................................................................................... 2
INTRODUCTION...................................................................................................................... 4
PACKAGE CONTENTS .......................................................................................................... 4
SYSTEM REQUIREMENTS .................................................................................................... 4
CONNECTION DIAGRAM ........................................................................................................ 5
DEVICE FUNCTION ................................................................................................................. 6
Transmitter Panel ............................................................................................................... 6
Receiver Panel .................................................................................................................... 7
IR Pin Assignment ............................................................................................................... 8
SPECIFICATION ....................................................................................................................... 8
Specification ....................................................................................................................... 8
Cable Specifications ............................................................................................................ 9
Support Resolution ............................................................................................................. 9
WARRANTY .......................................................................................................................... 10

EXP-HDBASET-101
INTRODUCTION
EXP-HDBASET-101 with us allows one HDMI, Bi-direction IR to be connected up to 100meters
via single CAT.6 cable for Computer, Laptop, BD Player, Game Console and others HDMI source
devices. Supporting 4Kx2K/30Hz UHD resolution with 8bit deep color and lossless
compressed audio that make EXP-HDBASET-101 a smart choice for home entertainment,
company conference, commercial advertising and other applications.
PACKAGE CONTENTS
 EXP-HDBASET-101 TX X 1 PCS
 EXP-HDBASET-101 RX X 1 PCS
 5VDC / 2.0 Amp Locking Power adapter X 2 PCS
 IR Blaster Cable X 1 PCS
 IR Receiver Cable X 1 PCS
 User Manual X 1 PCS
SYSTEM REQUIREMENTS
 HDMI Source device includes SetTop Box, BD Player, Computer, Laptop, Game
Console, Media Player and Camcorder.
 HDMI Sink device includes LED/LCD Monitor, LED/LCD TVs, Projector and AV
Receiver.
 HDMI 2.0 Premium Certified Cable-Highly recommended
 Standard 24AWG Cat.5e, Cat.6 or Cat.7 Cable-Highly recommended

EXP-HDBASET-101
CONNECTION DIAGRAM

EXP-HDBASET-101
DEVICE FUNCTION
Transmitter Panel
1. POWER LED : This LED will illuminate when power adapter plug in EXP-
HDBASET-101 TX.
2. HDMI LED : This LED will illuminate when TX connect compatible RX and
HDMI signal start to transmission.
3. LINK LED : This LED will illuminate when TX connect compatible RX and RJ45
signal start to transmission.
4. DC IN : 5VDC / 2.0 Amp Locking Power Jack
5. RJ45: Connect to EXP-HDBASET-101 Receiver with single Cat.6 cable for
HDMI, IR Blaster, IR Receiver signal transmission.
6. HDMI IN : Connect to HDMI source devices, such as SetTop Box, BD Player,
Computer, Laptop, Game Console, Media Player and Camcorder.
7. IR RX : Receiving IR signal to remote control HDMI sink devices via IR
Receiver Cable.
IR TX : Transmitting IR signal to remote control HDMI source devices via IR
Blaster Cable.

EXP-HDBASET-101
Receiver Panel
1. POWER LED: This LED will illuminate when power adapter plug in EXP-
HDBASET-101 TX.
2. HDMI LED : This LED will illuminate when TX connect compatible RX and
HDMI signal start to transmission.
3. LINK LED : This LED will illuminate when TX connect compatible RX and RJ45
signal start to transmission.
4. DC IN : 5VDC / 2.0 Amp Locking Power Jack
5. RJ45 : Connect to EXP-HDBASET-101 Transmitter with single Cat.6 cable for
HDMI, IR Blaster, IR Receiver signal transmission.
6. HDMI OUT : Connect to HDMI sink devices, such as LED/LCD Monitor,
LED/LCD TVs, Projector and AV Receiver.
7. IR RX : Receiving IR signal to remote control HDMI source devices via IR
Receiver Cable.
IR TX : Transmitting IR signal to remote control HDMI sink devices via IR
Blaster Cable.

EXP-HDBASET-101
IR Pin Assignment
SPECIFICATION
Specification
Model No EXP-HDBASET-101 TX EXP-HDBASET-101 RX
HDMI Bandwidth 340MHz
HDMI Resolution 720P/1080P(100m),4K30 4:4:4(70m),4k60 4:2:0(70m)
Audio Format LPCM、DTS Digital, Dolby Digital
HDCP 1.4/2.2
Input Port HDMI x 1 RJ45 x 1
Output Port
RJ45
x 1
H
DMI
x 1
Control Port IR Blaster x 1 - 3.5mm
IR Receiver x 1 - 3.5mm
IR Frequency 20-60Khz
Power Supply 5VDC / 2.0 Amp
Power Consumption 10W - Max.
Chassis Material Metal
Chassis Color Black
Operating Temperature 0℃ - 40℃ / 32℉ - 104℉
Storage Temperature -20℃ - 85℃ / -4℉ - 185℉
Humidity 0 - 95% RH (Non-Condensing)
Dimension 112 mm X 76 mm X 25 mm
Weight 600 g
I
R Receiver
I
R Blaster

EXP-HDBASET-101
Cable Specifications
Cable Length 1080p/60Hz 4K/30Hz 4K/60Hz
8 bit 8 bit 4:4:4 8 bit 4:2:0
HDMI Cable 2m 2m 2m
Cat.5e/6/6e/7 100m 70m 70m
Support Resolution
Supported Resolutions (Hz)
800x600@ 60 72 75
1024x768@60 70 75
1280x720p@50 59 60
1280x960@60 85
1280x1024@60 75 85
1360x768@60
1440x900@ 60 75
1600x900@60
1600x1200@60
1920x1080p@24 25 29 30
1920x1080p@60
2560x1440@60
2560x1600@60
2048x1080p@30
2048x1080p@60
3840x2160p@24 25 30(4:4:4 70m Cat.6)
3840x2160p@50 60 (4:2:0 70m Cat.6)
4096x2160p@24 25 30(4:2:0 70m Cat.6)
4096x2160p@50 60 (4:2:0 70m Cat.6)

EXP-HDBASET-101
WARRANTY
Limited 3 Year Warranty
aegis Multimedia INC. (“Manufacturer”) warrants that this product is free of defects in both materials and
workmanship for a period of 3 years as defined herein for parts and labor from date of purchase. This Limited
Warranty covers products purchased in the year 2019 and after. During the warranty period, and upon proof
of purchase, the product will be repaired or replaced (with same or similar model) at our option without
charge for parts or labor for the specified product lifetime warranty period.
This warranty shall not apply if any of the following:
A. The product has been damaged by negligence, accident, lightning, water, or mishandling.
B. The product has not been operated in accordance with procedures specified in operating instructions.
C. The product has been repaired and or altered by other than the manufacturer or authorized service
center.
D. The product's original serial number has been modified or removed.
E. External equipment other than supplied by the manufacturer, in the determination of a manufacturer,
shall have affected the performance, safety or reliability of the product.
F. Part(s) are no longer available for the product.
If the product needs repair or replacement during the specified warranty period, the product should be
shipped back to Manufacturer at Purchaser's expense. Repaired or replaced product shall be returned to
Purchaser by standard shipping methods at Manufacturer's discretion. Express shipping will be at the
expense of the Purchaser.
No other warranty, express or implied other than Manufacturers shall apply.
The manufacturer does not assume any responsibility for consequential damages, expenses or loss of
revenue or property, inconvenience or interruption in operation experienced by the customer due to a
malfunction of the purchased equipment. No warranty service performed on any product shall extend the
applicable warranty period. This warranty does not cover damage to the equipment during shipping and
Manufacturer assumes no responsibility for such damage. This product warranty extends to the original
purchaser only and will be null and avoid upon any assignment or transfer.